• 대한기계학회논문집A
• /
• 제28권5호
• /
• pp.654-661
• /
• 2004

In deep drawing of sheet metal, there are many cases in which the uniform and thin wall thickness of the drawn products is more important than the bottom thickness. In this case, we can not easily get the deep drawn products with the uniform and precise wall thickness by only drawing process. Therefore in general the manufacturing processes which both the drawing and the ironing process are proceeded sequentially are used. But this method has the disadvantages of a cost-up, decrease of productivity and degradation of quality, because the ironing process is added after the drawing process. In this study, in order to improve those problems and to enhance the effect of deep drawing, the combined process of redrawing and ironing fur multistep drawing of cylindrical cups is used. In this experiment, we considered the characteristics of the combined process such as the relation between the drawing and ironing rates, the drawing limits and the forces needed for operations. The suggested force prediction shows that it can successfully represent experimental results.

• 소성∙가공
• /
• 제7권4호
• /
• pp.393-399
• /
• 1998

For minimizing wall thickness thinning of circular shells, a new stamping technology, the deep draw-ing process combined with ironing is approached and investigated. The design requirements for the deep drawing shells are to keep the optimum wall thickness with max. 10 percent thickness thinning of the initial blank thickness, to make uniform thickness strain distribution for the wall of circular shell and to improve the shape accuracy for the roundness and concentricity. In order to check the validity and effectiveness of proposed work, a sample process design is applied to a circular shell needed for a 4multi-stepped deep drawing. Through experiments, the variations of the thickness strain distribution in each drawing process are observed. Also a series of experiments are performed to investigate optimum process variables such as the geometry of tooling, radius and drawing rate. In particular, the advantage of current approach with ironing is shown in contrast to the conventional deep drawing process. From the results of proposed method, the optimum value of process variables are obtained, which contribute more uniform thickness strain distribution and better quality in the drawn product.

• 한국정밀공학회지
• /
• 제19권2호
• /
• pp.177-186
• /
• 2002

This paper describes a research work on the development of computer-aided design system far the deep drawing & ironing of high pressure gas cylinder. An approach to the design system is based on the knowledge-based rules. Knowledge for the system is formulated from plasticity theories, handbook, experimental results and the empirical knowledge of field experts. This system has been written in AutoLISP on the AutoCAD Rl4.0 using personal computer. This system is composed of three modules which are input. process design and drawing.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.943-948
• /
• 1996

In this paper. we will discuss in making large size cylindrical shells with multithickness wall sections such as straight, stepped, tapered sides. These shells are constructed of type 6061 O temper aluminum starting with a blanking size of 877 mm plate. Its diameter to length ratio of 1 to 2.78 and a 36.7％ wall reduction is achieved by our continuous deep drawing process. This process required no in-process annealing. But after cold working, these shells is performed heat treatment to T6 condition. These shells are used for the making of seamless LPG pressure vessels after the spinning process. This process is composed of deep drawing, reverse redrawing, drawing-ironing and several ironing processes. In the verification of forming process design, we used DEFORM code.

• International Journal of Precision Engineering and Manufacturing
• /
• 제6권4호
• /
• pp.31-36
• /
• 2005

This paper describes a research work on the die design for the deep drawing & ironing(D. D. I) of high pressure gas cylinder. D. D. I die set is large-sized die used in horizontal press, which is usually composed of a drawing, and an ironing die. Design method of D. D. I die set is very different from that of conventional cold forging die set. Outer diameter of the die set is fixed because of press specification and that of the insert should be as small as possible for saving material cost. In this study, D. D. I die set has been designed to consider those characteristics, and the feasibility of the designed die has been verified by FE-analysis. In addition, the automated system of die design has been developed in AutoCAD R14 by formulating the applied methods to the regular rules.

• 소성∙가공
• /
• 제24권2호
• /
• pp.115-120
• /
• 2015

Deep drawing of cylindrical cups is one of the most fundamental and important processes in sheet metal forming. Circular cups are widely used in industrial fields such as automobile and electronic appliances. Some of these cups are formed by a one-stage process, others such as battery cases and beverage cans are made by a multi-stage process. In the current study the multi-stage deep drawing of aluminum sheet metal is examined. The process consists of two deep drawing operations followed by two ironing operations. The press die, which can be used for the four-stage forming process, was manufactured allowing punch and die components to be easily changed for various experiments. The rolling direction of both the sheet and the drawn cups was always positioned toward the horizontal x-direction on the die face to minimize experimental errors during the progressive forming. The dimensional accuracy of the cylindrical cups formed at each stage and the earing defect due to the anisotropy of sheet were investigated. The influence of anisotropy on the thickness distribution was also examined. Both the thickness and the outer diameter of the cups were measured and compared for each set of experimental conditions. It was found that the dimensional accuracy of cups rapidly improves by employing the ironing process and also by increasing the amount of ironing.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.97-100
• /
• 2000

Today deep drawing and ironing are the major process in manufacturing of battery case used in cellular phone from aluminum. The same technology is utilized in manufacturing of steel or aluminum cans for components of medical instrument, portable PC, walkman and so on. Most of these processes require multi-stage ironing following the deep drawing and redrawing processes. The practical aspects of this technology are well known and gained through extensive experiment and production know-how. However, the fundamental aspects of theses processes are relatively less known. Thus, it is expected that process simulations using FEM techniques would provide additional detailed information that could be utilized to improve the process condition. This paper illustrates the application of process modeling to deep drawing and redrawing operations for High Precision Rectangular Battery Case. A commercially avaliable finite element code LS-DYNA3D was used to simulate deep drawing and redrawing operations.

• 소성∙가공
• /
• 제10권6호
• /
• pp.456-464
• /
• 2001

Deep drawing and ironing are tile major process today in manufacturing of aluminum alloy battery case used in cellular phone. Most of these process require multi-stage ironing following the deep drawing and redrawing processes. The practical aspects of this technology are well known and gained through extensive experiment and production know-how. However, the fundamental aspects of these processes are relatively less known. Thus, it is expected that process analysis using FEM techniques would provide additional detailed information that could be utilized to improve the process condition. This paper illustrates the application of process modeling to deep drawing and redrawing operations. To verify the simulation results, the experimental investigations were also carried out on a real industrial product. The numerical analysis by FEM shows good agreement with the experimental results in view of the deformation shape of the product. A commercially available finite element code LS-DYNA3D was used to simulate deep drawing and redrawing operations.

• 대한기계학회논문집A
• /
• 제26권6호
• /
• pp.1077-1084
• /
• 2002

Optimum tool design is carried out fur a multi-stage rectangular cup deep-drawing and ironing process with the large aspect ratio. Finite element simulation is carried out to investigate deformation mechanisms with the initial design made by an expert. The analysis considers the deep drawing process with ironing for the thickness control in the cup wall. The analysis reveals that the difference of the drawing ratio within the cross section and the irregular contact condition produce non-uniform metal flow to cause wrinkling and severe extension. For remedy, the modification guideline is proposed in the design of the tool and the process. Analysis results confirm that the modified tool design not only improves the quality of a deep-drawn product but also reduces the possibility of failure. The numerical result shows fair coincidence with the experimental one. After tryouts of the tool shape, the rectangular cup has been produced in the transfer press.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.630-634
• /
• 1997

In this paper,we will discuss in the forming process design of the making engine pulleys for automobiles. These pulleys are required to be made by precision deep drawing process because these are to be combined with bearings and engine timing belts. These pulleys are used of cold rolled steel plates starting with the initial blanking size of 115.2mm and the initial thickness of 1.2mm. Our deep drawing process is designed the continuous 5-steps process, that is, 1'st deep drawing, 2'nd reverse redrawing, 3'rd trimming, 4'th drawing-ironing and 5'yh piercing. This process need no in-process annealing.