• Proceedings of the Korean Geotechical Society Conference
• /
• 1999.10a
• /
• pp.209-216
• /
• 1999

In tunneling and road cuts by blasting, it is of the utmost importance that the remaining rock is of high quality in order to avoid rockfall, rockslides and excessive maintenance work. Therefore, numerous blasting techniques which make use of decoupled charge or shock wave superposition effect have been used to control overbrake. In this paper. some approximate method for the determination of blast load according to the charge condition was introduced at first and, instrumented tests were conducted in small scale transparent material to investigate the shape and amplitude of blast load around the bore hole. Compare to the fully coupled charge, low amplitude of blast load around the bore hole was observed in the decoupled charge and explosion gas pressure was important in the shape of blast load. Therefore, quasi-static behaviour of the crack pattern was shown due to low loading rate.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.75-85
• /
• 2003

Laboratory model blast and in-situ rock blast tests were conducted to determine blast-induced stress wave propagation characteristics under different explosive types, different loading conditions and different mediums. Dynamic numerical approaches were conducted under the same conditions as experimental tests. Stress magnitudes at mid-point between two blast holes which were detonated simultaneously increased up to two times those of single hole detonation. The rise time of maximum stress in a decoupled charge condition was delayed two times that of a fully charged condition. Dynamic numerical analysis showed almost similar results to blast test results, which verifies the effectiveness of numerical approaches fur optimizing the tunnel blast design. Dynamic numerical analysis was executed to evaluate rock behavior and damage of the contour hole, the sloping hole adjacent to the contour hole in the road tunnel blasting pattern. The rock damage zone of the sloping hole from the numerical analysis was larger than that of the contour hole. Damage in the sloping hole can be reduced by using lower density explosive, by applying decoupled charge, or by increasing distance between the sloping hole and the contour hole.

• Explosives and Blasting
• /
• v.41 no.1
• /
• pp.32-45
• /
• 2023

Environmental regulations in Korea for blasting at industrial sites have conservative standards, which often result in reduced efficiency and cost-effectiveness due to the consideration of environmental regulations and public complaints. Therefore, there is a need for blasting methods that can reduce environmental damage while improving construction efficiency and cost-effectiveness. In this study, we analyzed the effects of the PA-Deck (Paraffin Air-Deck) blasting method, which is a kind of Air Decoupled Charge method in principle utilizing a paraffin-infused paper tube as an air gap, on reducing blasting hazards and improving blasting efficiency. The analysis also evaluated the effectiveness of newly applied equipment for collecting blasting vibration data, and derived the relationship between the explosion velocity and vibration velocity of explosives, and performed frequency analysis of the vertical component. The results of the blasting vibration velocity analysis showed that the Paraffin Waxed Paper Tube-based blasting method exhibited significantly lower vibration velocities compared to conventional blasting methods, and it was judged that more uniformly small-sized fragmented rocks were generated.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.6 no.4
• /
• pp.291-302
• /
• 2004

Blast-induced anisotropic rock damage around a blast-hole was analyzed by a using numerical method with user-defined subroutine based on continuum damage mechanics. Anisotropic blasting pressure was evaluated by applying anisotropic ruck characteristics to analytical solution which is a function of explosive and rock properties. Anisotropic rock damage was evaluated by applying the proposed anisotropic blasting pressure. Blast-induced isotropic rock damage was also analyzed. User-defined subroutines to solve anisotropic and isotropic damage model were coded. Initial rock damages in natural ruck were considered in anisotropic and isotropic damage models. Blasting pressure and elastic modulus of rock were major influential parameters from parametric analysis results of isotropic rock damage. From the results of anisotropic rock damage analysis, blasting pressure was the most influential parameter. Anisotropic rock damage area in horizontal direction was approximately 34% larger and about 12% smaller in vertical direction comparing with isotropic rock damage area. Isotropic rock damage area under fully coupled charge condition was around 30 times larger than that under decoupled charge condition. Blasting pressure under fully coupled charge condition was estimated to be more than 10 times larger than that of decoupled charge condition.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.5
• /
• pp.63-74
• /
• 2000

지하구조물 걸설시 발파에 의한 암반의 굴착공법이 일반적으로 사용된다. 그러나 발파에 의한 암반의 굴착은 잔존암반의 손상과 진동을 유발하는 문제점을 가지고 있다. 현재까지는 이러한 암반의 손상과 진동문제를 해결하기 위해 현장계측을 기초로한 경험적인 방법이 이용되어 왔으나 여러 가지 한계점을 지니고 있는 것이 현실이다. 따라서 수치해석에 의한 터널 발파의 모델링을 이용하면 이러한 한계점을 보완할수 있을 것이다. 본 논문에서는 발파에 의한 발파공 주위 암반의 거동을 유한요소해석을 이용하여 규명하고, 토로터널의 표준발파패턴을 기초로 하여 외과공 발파와 외곽공에 인접한 주변공 발파에 의한 암방의 손상의 손상을 비교하여 발파패턴의 적절성을 평가하고자 하였으며, 이를 근거응 발파에 의한 암반의 손상을 최소하기 위한 발파패턴의 최적화를 도모하였다.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.4
• /
• pp.89-102
• /
• 2004

The generated blasting pressure wave initiated under decoupled-charge condition is a function of peak blasting pressure, rise time, and wave-shape function. The peak blasting pressure and the rise time are also the function of explosive and rock properties. The probabilistic distributions of explosive and rock properties are derived from the results of their property tests. Since the probabilistic distributions of explosive and rock properties displayed a normal distribution, the peak blasting pressure and the rise time can also be regarded as a normal distribution. Parameter analysis and uncertainty analysis were performed to identify the most influential parameter that affects the peak blasting pressure and the rise time. Even though the explosive properties were found to be the most influential parameters on the peak blasting pressure and the rise time from the parameter analyses, the result of uncertainty analysis showed that rock properties constituted major uncertainties in estimating the peak blasting pressure and the rise time rather than explosive properties. Damage and overbreak of the remaining rock around the excavation line induced by blasting were evaluated by dynamic numerical analysis. A user-subroutine to estimate the rock damage was coded based on the continuum damage mechanics. This subroutine was linked to a commercial program called 'ABAQUS/Explicit'. The results of dynamic numerical analysis showed that the rock damages generated by the initiation of stopping hole were larger than those from the initiation of contour hole. Several methods to minimize those damages were proposed such as relocation of stopping hole, detailed subdivision of rock classification, and so on. It was found that fracture probability criteria and fractured zones could be distinctively identified by applying fuzzy-random probability.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.128-128
• /
• 2012

We investigated the atomic and electronic properties of graphene grown by Pd silicidation and intercalation using LEED, STM, and ARPES. Pd was deposited on the 6H-SiC(0001) surface at RT. The formation of Pd silicide gives rise to breaking of Si-C bonds of the SiC crystal, which enables to release C atoms at low temperature. The C atoms are transformed into graphene from $860^{\circ}C$ according to the LEED patterns as a function of annealing temperature. Even though the graphene spots were observed in the LEED pattern and the Fourier transformed STM images after annealing at $870^{\circ}C$, the topography images showed various superstructures so that graphene is covered with Pd silicide residue. After annealing at $950^{\circ}C$, monolayer graphene was revealed at the surface. The growth of graphene is not limited by surface obstacles such as steps and defects. In addition, we observed that six protrusions consisting of the honeycomb network of graphene has same intensity meaning non-broken AB-symmetry of graphene. The ARPES results in the vicinity of K point showed the non-doped linear ${\pi}$ band structure indicating monolayer graphene decoupled from the SiC substrate electronically. Note that the charge neutrality of graphene grown by Pd silicidation and intercalation was sustained regardless of annealing temperature in contrast with quasi-free- standing graphene induced by H and Au intercalation. Further annealing above $1,000^{\circ}C$ accelerates sublimation of the Pd silicide layer underneath graphene. This results in appearance of the $(6r3x6r3)R30^{\circ}$ structure and dissolution of the ${\pi}$ bands for quasi-free-standing graphene.