• 소성∙가공
• /
• 제8권4호
• /
• pp.364-373
• /
• 1999

For material characterization of semi-solid materials, backward extrusion process, which has been used in forming of hollow-sectioned products, was analyzed by the upper bound analysis in the current study. The existing kinematically admissible velocity field was applied to steady state at which there was no change in the assumed regions of velocity field. For unsteady state, new velocity field, as a function of dead zone angle, was proposed. Through the whole analysis, fiction between die and workpiece was also considered. It has been studied how the process variables, such as friction factor and punch velocity, and material parameters, such as strength coefficient, strain rate sensitivity could affect on analysis results. Finally, by the comparison with the finite element analysis, the reliability and efficiency of the proposed velocity field were discussed.

• 반도체디스플레이기술학회지
• /
• 제22권4호
• /
• pp.32-37
• /
• 2023

For the potential applications in large-area OLED lightings, hydrogen fuel cells, and secondary batteries, we have performed an intermittent coating of high-viscosity polydimethylsiloxane using roll-to-roll slot die coater. During intermittent coating, dead zones inevitably appear where the thickness of PDMS patch films becomes non-uniform, especially at the leading/trailing edge. To reduce it, we have coated the PDMS patches by varying the process parameters such as the installation angle of the slot die head, coating speed, and patch interval. It is observed that the PDMS solution flows down and thus the thickness profile is non-uniform for horizonal intermittent coating, whereas the PDMS solution remaining on the head lip causes an increase in the PDMS thickness at the leading/trailing edges for vertical intermittent coating when the coating velocity is low. As the coating speed increases, however, the dead zone is shown to be reduced. It is addressed that the overall dead zone (the dead zone at the leading edge + the dead zone at the trailing edge) is smaller with horizontal intermittent coating than with vertical intermittent coating.

• 산업기술연구
• /
• 제29권A호
• /
• pp.111-122
• /
• 2009

In this study, flood stage was computed by HEC-RAS, 1-D numerical analysis model and FESWMS-2DH, 2-D numerical model. Flood stages computed by two different models were compared for straight line, dot axle watercourse, dead-zone watercourse, section sudden-changing watercourse, and curved watercourse. From the results, flow velocity and water level were similar in straight watercourse and dot-reduction watercourse. However, there was difference of flow velocity and water level in dead-zone watercourse, sudden expansion, dot-reduction, and curve-watercourse. This result might be influenced by rapid change of watercourse due to dead-zone, the angle of inflow and outflow, and the curvature. Especially in this study, numerical model was applied to Wol-Song-Cheon at Chuncheon in order to analyze the effect of flood stage by two different models. By flowing properties around the bridge and confluence of rivers, it was found that flow velocity and water level was changed. Therefore, it was concluded that a lot of uncertainties are contained in the present bank.

• 한국재료학회지
• /
• 제4권7호
• /
• pp.837-844
• /
• 1994

현재까지 잘 알려진 압출이론식이 생산현장에 응용될 수 있는가를 조사하기 위하여, Al-Si합금을 대상소재로 하여 각 압출이론식에 나타난 유도응력 $K_f$, 변형저항 $K_w$ , Dead Metal Zone(DMZ)의 경각($\alpha$)등을 측정하였으며, 이들 값을 이용하여 최대압출력을 계산하였다. 550ton의 압출기를 이용하여 측정한 최대 압출력과의 비교분석을 행하였으며, 그 결과 이론식에 의해 최대압출력을 계산하기 위해 측정된 유동응력 및 변형저항 값은 신뢰할 수 있을 것으로 사료되었는데, 이것은 0.5이하에서 결정된 변형효율 $\eta _f$로서 판단 할 수 있었다. 최대 압출력은 Si함량이 증가할 수록 증가하게 되나, 압출온도가 증가할 수록 감소하고 있음을 알 수 있었다. Siebel식으로부터 계산된 최대압출력은 본 실험을 통하여 얻어진 최대압출력에 비교적 근접하고 있으나. Geleji식으로부터 계산된 최대압출력은 DMZ의경각 $\alpha$가 $50^{\circ}$일 경우 , 본 실험에 의해 얻어진 실제의 최대압출력에 급접하고 있었다. Geleji의 식은 DMZ의 경각에 매우 민감하고, 대상재료마다. DMZ를 일일이 측정해야 하는 번거로움 때문에 생산현장에서는 Siebel의 식을 이용하는 것이 보다 편리할 것으로 사료된다.

• 수산해양기술연구
• /
• 제36권3호
• /
• pp.202-209
• /
• 2000

저서어의 음향자원조사에 있어서 해저 데드존에 의한 어군량의 추정오차에 관하여 고찰하기 위하여, 북해도 분화만과 동중국해 에 서 행 한 음향자원조사의 에코적분데이터를 이용하여 그 정도를 알아보았다. 그리고 해저상의 에코파형의 형상으로부터, 어군분포 패턴을 고려하여 데드존 내에 어군이 존재할 경우 그 에코파형을 발산형, 평행형, 수렴형으로 정의한 데드존 보정법을 제안하고 이를 이용한 보정을 행하였다. 북해도 분화만 내에 회유하는 명태어군을 대상으로 데이터를 재평가한 결과 해저 직상의 1∼2m내의 SV가 2∼3dB, 자원량으로 약 2배 증가하였으며, 동중국해의 경우에 있어서는 해저 직상 1∼2m에 어군이 집중되어 분포하고 있는 경우 SV가 최대 17dB까지 증가하였으며, 이는 자원량으로 약 50배 증가한 것 과 같았다. 끝으로, 계량어군탐지기를 이용하여 저서어의 자원량을 추정할 경우에는 해저기준의 최적화와 정확한 해저기준을 이용한 적분구간 오프셋 설정의 최소화를 달성한 후에 해저의 에코에 마스크되어 있는 어군의 에코를 어떠한 방법을 통하여 보정하여, 지금까지 기술적 곤란으로 제약을 점차 줄여 나감으로서 저서어를 대상으로 한 음향자원 조사 방법이 좀 더 고도화하여, 실용화할 수 있도록 노력해야 할 것으로 생각된다.

• 한국유체기계학회 논문집
• /
• 제8권3호
• /
• pp.33-41
• /
• 2005

The optimum condition is defined as one that best suits the purpose of flocculation; the number of small particles should decrease, while that of large particles should increase. The object of this research was to develop a new impeller and substitute for conventional flocculators. The flow characteristics of turbines and hydrofoil type flocculators in turbulent fluids were observed using a standard $k-{\epsilon}$ Model and a computational fluid dynamics (CFD) simulation program-FLUENT. The experiments were performed to compare PBT(Pitched Blade Turbine) flocculator with twisted hydrofoil type flocculators for velocity distribution, and floe formation at conventional water treatment plants in Korea. As a result of the CED solution, twisted hydrofoil types are similar to hydrofoil flocculators for flow characteristics without regard to the twisted angle, On the other hand, it was established that turbine flocculators are greater than hydrofoil flocculators with flow unevenness and dead zone formation. Twisted hydrofoil type-II (Angle $15{\sim}20^{\circ}$) is the most proper impeller for water flocculation from this point of view with a decreasing the dead zone, maintaining of the equivalent energy distribution and a drawing up of the sedimentation substance from the bottom of the flocculation basin.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.267-274
• /
• 2004

The optimum condition is defined as one that best suits the purpose of flocculation; the number of small particles should decrease, while that of large particles should increase. The object of this research was to develop a new impeller and substitute for conventional flocculators. The flow characteristics of turbines and hydrofoil type flocculators in turbulent fluids were observed using a standard k-$\epsilon$ Model and a computational fluid dynamics (CFD) simulation program- FLUENT The experiments were performed to compare PBT(Pitched Blade Turbine) flocculator with twisted hydrofoil type flocculators for velocity distribution, and floc formation at conventional water treatment plants in Korea. As a result of the CFD solution, twisted hydrofoil types are similar to hydrofoil flocculators for flow characteristics without regard to the twisted angle, On the other hand, it was established that turbine flocculators are greater than hydrofoil flocculators with flow unevenness and dead zone formation. Twisted hydrofoil type- II (Angle $15{\~}20^{\circ}$) is the most proper impeller for water flocculation from this point of view with a decreasing the dead zone, maintaining of the equivalent energy distribution and a drawing up of the sedimentation substance from the bottom of the flocculation basin.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1489-1494
• /
• 2003

A neuromuscular control system of a myoelectric prosthetic hand (PH) constitutes a nonlinear system with a dead zone whose magnitude is equal to its joint angle when the PH just grasps an object. This is because the neuromuscular control system remains an open-loop system until the PH grasps the object but it constitutes a feedback control system after the PH griped the object in which a torque induced in the fingers of the PH is fed back. To improve the transient performance of the control system, it is desirable to make the feed-forward gain as large as possible, so long as the stability of the system is not impaired. It is also desired that the control system remains stable even when the PH lifts a heavy or rigid object, because this makes the closed loop gain large and leads to the closed system unstable. According to the theory of stability analysis of nonlinear systems, we can only know the sufficient conditions that the system should be stable. Thus the nonlinear theory on stability is insufficient to be used to design the neuromuscular control system for improving its transient responses. This paper shows that the nonlinear system with a dead zone can be approximated to a linear feedback system and that well-known methods of analysis and design on linear control systems can be applicable. It is also shown through various simulation results that errors induced by approximation are practically negligible and thus the design methods are quite accurate.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.1105-1109
• /
• 1995

A CCD-camera, which is structured with vision system, was used to realize automatic seam-tracking system and 3-D information which is needed to generate torch path, was obtained by using laser-slip beam. To extract laser strip and obtain welding-specific point, Adaptive Hough-transformation was used. Although the basic Hough transformation takes too much time to process image on line, it has a tendency to be robust to the noises as like spatter. For that reson, it was complemented with Adaptive Hough transformation to have an on-line processing ability for scanning a welding-specific point. the dead zone,where the sensing of weld line is impossible, is eliminated by rotating the camera with its rotating axis centered at welding torch. The camera angle is controlled so as to get the minimum image data for the sensing of weld line, hence the image processing time is reduced. The fuzzy controller is adapted to control the camera angle.

• Journal of Welding and Joining
• /
• 제16권6호
• /
• pp.68-76
• /
• 1998

A CCD camera with a laser stripe was applied to realized the automatic weld seam tracking. The 3-dimensional information obtained from the vision system made it possible to generate the weld torch path. The adaptive Hough transformation was used to extract laser stripes an to obtain specific weld points. It takes relatively long time to process image on-line control using the basic control using the basic Hough transformation, but it has a tendency of robustness over the noises such as spatter. For this reason, it was complemented with adaptive Hough transformation to have an on-line processing ability for scanning specific weld points. The dead zone, where the sensing of weld line is impossible, was eliminated by rotating the camera with its rotating axis centered at the weld torch. When weld lines were detected, the camera angle was controlled in order to get the minimum image data for sensing of weld lines. Consequently, the image processing time was reduced.