• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제54권12호
• /
• pp.616-621
• /
• 2005

We considered of the buck and half bridge series DC-DC converter. It has good applications in areas with low voltage/high current, wide input voltage. The buck converter ratings and the half bridge converter ratings are $36\~72V$ input and 22V/5A output, $19\~24V$ input and 3.3V/30A output, respectively. Developed the buck and half Bridge series DC-DC converter ratings are of $36\~72V$ input and 3.3V/30A output. The buck converter is operated with zero voltage switching process to reduce the switching losses. The $80.1\%\~97.6\%$ of the efficiency is measured at $18.4{\mu}H$ output filter inductance of buck converter. In the half bridge converter, the $86\%\~96.4\%$ efficiency is measured at 150kHz switching frequency with PQI core. In the case of synchronized the buck and half bridge DC-DC converter, the measured efficiency is higher than that of the unsynchronized converter. In the synchronized converter, the maximum efficiency is measured up to $92.3\%$ with PQI core at 150kHz. 7A output.

• 산업기술연구
• /
• 제30권A호
• /
• pp.69-73
• /
• 2010

In this paper, we designed the RF-DC converter used in wireless power transmission system and studied how to design the RF-DC converter of high conversion efficiency. The RF-DC converter operate at 2.45GHz and the diode is connected with series. The RF-DC converter uses shorted stub for DC loop and matching. We can divide the RF-DC converter circuit into four blocks. The reflection coefficients between the blocks were optimized for the maximum conversion efficiency at 0 dBm input power and $1300{\Omega}$ load impedance. The final design of the RF-DC converter has a 52 percent conversion efficiency.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.83-86
• /
• 2002

This paper presents an implementation of Pill controller for DC-DC converter using the microcontroller. The features of the microcontroller such as the on chip ADC and Pulse width Modulator (PWM) eliminate the external components needed to perform these functions. The duty rate cycle for the DC-DC converter can be updated every time when the (ADC) conversation and the calculation time are finished. The stable response can be obtained for any kind of DC-DC converters. The SMPS controller looks at the converter output, compares the output to a set point, performs a control algorithm (Pill algorithm) and finally applies the algorithm output to the PWM. PWM output is then used to drive the DC-DC converter. Figure (1) shows a simplified block diagram of a complete DC-DC converter system.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1825-1831
• /
• 2011

One of the major trends in traction power electronics is increasing the switching frequencies. The advances in the frequency elevation have made it possible to reduce the total size and weight of the passive components such as capacitors, inductors and transformers in the DC/DC converter and hence to increase the power density. The traction dynamic performance is also improved. This document describes several aspects relating to the design of resonant DC/DC converter operating at high frequency(10KHz) and the converter topologies and the control method of MAGLEV, which result in soft switching, are discussed.

• 전기학회논문지
• /
• 제65권1호
• /
• pp.81-87
• /
• 2016

An LCL-type Isolated dc-dc converter operating for constant output voltage is analyzed, including the effect of a high frequency transformer using ac complex circuit approximation. Its solution is derived and is used to obtain the characteristics of the proposed converter. The analyses show through converter modeling, phasor diagram and gain comparison that inclusion of a high frequency transformer results in introduction of magnetizing inductance and leakage inductances at conventional LCL dc-dc converter with ideal transformer. The theoretical and simulation results are presented in case of the wide variations in input voltage and load current in detail. Analysis and simulation results observed that introduction of a transformer in the dc-dc converter had considerable effect on the performance, especially in the case of low output voltage and large load.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제1권1호
• /
• pp.67-76
• /
• 2012

Due to the increasing amount of applications of power electronic ac-dc converters, it is necessary to design a single-stage converter that can reliably perform both buck and boost operations. Traditionally, this can be achieved by double-stage conversion (ac/dc-dc/dc) which ultimately leads to less efficiency and a more complex control system. This paper discusses two types of modern ac-dc converters. First, the novel impedance-source ac-dc converter, abbreviated as custom Z-source rectifier, is analyzed; and then, switched inductor (SL) Z-source ac-dc converter is proposed. This paper describes the Z-source rectifiers' operating principles, the concepts behind them, and their superiorities. Analysis and simulation results show that the proposed custom Z-source rectifier can step up and step down voltage; and the main advantage of the SL Z-source ac-dc converter is its high step-up capability. Low ripple of the output dc voltage is the other advantage of the proposed converters. Finally, the SL Z-source ac-dc converter is compared with the custom Z-source ac-dc converter.

• 전력전자학회논문지
• /
• 제12권1호
• /
• pp.56-64
• /
• 2007

최근 소형, 경량화 및 저가격화를 위해 절연형 고주파링크 승압 DC/DC 컨버터가 PCS (Power Conditioning System)에 많이 적용되고 있다. 하지만, 기존 전압형 컨버터 또는 전류형 컨버터가 적용된 고주파 링크 승압컨버터는 순환전류에 따른 도통손실과 변압기 누설인덕턴스에 따른 서지전압에 의해 여러 문제점을 내포하고 있다. 이들 문제들을 개선하기위해 새로운 2차측 LLC 직렬공진컨버터를 제안했고, 이에 대한 이론적 해석과 동작파형 및 시뮬레이션을 통해 800W급 시제품을 제작하여 실험결과에 대해 서술하였다.

• 전력전자학회논문지
• /
• 제20권3호
• /
• pp.280-289
• /
• 2015

A high-efficiency full-bridge DC-DC converter with a current-doubler rectifier and an asymmetric pulse-width modulation is proposed. Through the asymmetric pulse-width modulation, the proposed converter achieves zero-voltage switching of power switches without the circulating currents. The proposed converter reduces the output current ripple through the current-doubler rectifier. A control strategy is suggested for the proposed converter to charge battery banks. A constant current and constant voltage charging is performed. The proposed converter achieved a higher efficiency compared with the conventional full-bridge DC-DC converter with a phase-shift modulation. The performance of the proposed converter is evaluated by the experimental results for a 1.0 kW prototype circuit.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제55권8호
• /
• pp.423-429
• /
• 2006

Recently, the high frequency isolated boost DC/DC converter has been widely used for the PCS (Power Conditioning System) system because of its small size and low cost. However, the high frequency isolated boost DC/DC converters applied the conventional voltage-fed converter and current-fed converter have the problems such as the high conduction losses and the surge voltage due to the high circulating current and the leakage inductance, respectively. To overcome this problems, in this paper the secondary LLC resonant converter is proposed, and the experimental results of the secondary LLC series resonant converter for boost DC/DC converter are verified on the simulation based on the theoretical analysis and the 700W experimental prototype.

• Journal of Power Electronics
• /
• 제15권6호
• /
• pp.1438-1445
• /
• 2015

A new DC-DC power converter is researched for renewable energy and battery hybrid power supplies systems in this paper. At the charging mode, a renewable energy source provides energy to charge a battery via the proposed converter. The operating principle of the proposed converter is the same as the conventional DC-DC buck converter. At the discharging mode, the battery releases its energy to the DC bus via the proposed converter. The proposed converter is a non-isolated high step-up DC-DC converter. The coupled-inductor technique is used to achieve a high step-up voltage gain by adjusting the turns ratio. Moreover, the leakage-inductor energies of the primary and secondary windings can be recycled. Thus, the conversion efficiency can be improved. Therefore, only one power converter is utilized at the charging or discharging modes. Finally, a prototype circuit is implemented to verify the performance of the proposed converter.