• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.12
• /
• pp.1184-1191
• /
• 2009

Energy harvesting from environment can make the energy constrained systems such as sensor networks to sustain their lifetimes. However, environmental energy is highly variable with time, location, and other factors. Unlike the existing solutions, we solved this problem by allowing the sensor nodes with mobilizer to move in search of energy and recharge from remote energy station. In this paper we present and analyze a new harvesting aware framework for mobile sensor networks with remote energy station. The framework consists of energy model, motion control system and data transfer protocol. Among them, the objective of our data transfer protocol is to route a data packet geographically towards the target region and at the same time balance the residual energy and the link connectivity on nodes with energy harvesting. Our results along with simulation can be used for further studies and provide certain guideline for realistic development of such systems.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.534-538
• /
• 1995

In this paper, a realization of a real-time train information system(TIS) is discussed. The requirements of TIS which satisfy real-time constraints are analyzed in view of data transfer. For efficient data communication in TIS, a new network system is suggested and its real-time characteristics are analyzed and compared with the standard network system. A local unit is designed based on VMEbus system.

• Proceedings of the KIEE Conference
• /
• 2008.11a
• /
• pp.379-381
• /
• 2008

TETRA(Terrestrial Trunked Radio) is a digital trunked radio standard developed by the ETSI(European Telecommunications Standards Institute). Currently, TETRA was set Digital TRS in electric power If wireless backbone network. In this time, we use many company's TETRA modem. So, TETRA modem performance evaluation is very important. TETRA modem use two type of Data transfer mode. One is Packet Data using UDP/IP. and the other is SDS(Short Data Service). In this paper, We generate Packet Data using Traffic Generator module. Packet Data transfer 1000 times each 10 bytes to 400 bytes. We analyze transmission delay time, success rate and standard deviation.

• ETRI Journal
• /
• v.34 no.4
• /
• pp.553-563
• /
• 2012

Serial peripheral interface (SPI) has been identified as a bottleneck in many wireless sensing systems today. SPI is used almost universally as the physical connection between the microcontroller unit (MCU) and radios, storage devices, and many types of sensors. Virtually all wireless sensor nodes today perform up to twice as many bus transactions as necessary to transfer a given piece of data, as an MCU must serve as the bus master in all transactions. To eliminate this bottleneck, we propose the master-handoff protocol. After the MCU initiates reading from the source slave device and writing to the sink slave device, the MCU as a master becomes a slave, and either the source or the sink slave becomes the temporary master. Experiment results show that this master-handoff technique not only cuts the data transfer time in half, but, more importantly, also enables a superlinear energy reduction.

• 한국HCI학회:학술대회논문집
• /
• 2007.02a
• /
• pp.1025-1030
• /
• 2007

여러 학계와 산업계로부터 인체영상과 같은 정적인 볼륨 데이터뿐만 아니라, 유체 흐름과 같은 동적으로 움직이는 Time-Variant 볼륨 데이터에 대한 실시간 렌더링의 요구가 계속되고 있다. 일반적으로 Time-Variant 데이터는 그 크기가 정적 볼륨 데이터의 수배에서 수백 배에 이르러, 이를 실시간으로 가시화하는 데에 많은 어려움이 있어왔다. 한편, PC 그래픽스 하드웨어의 급격한 발전에 따라 슈퍼컴퓨터나 다수의 컴퓨터들을 이용한 병렬/분산 렌더링으로나 가능했던 Time-Variant 볼륨 데이터의 실시간 볼륨 렌더링을 한대의 일반 PC에서 수행하려는 시도가 계속되고 있다. GPU의 꼭지점 및 프래그먼트 쉐이더(vertex & fragment shader)는 수치 계산에 최적화된 벡터 연산과 사용자 프로그래밍 기능으로 빠른 볼륨 렌더링을 일반 PC에서도 가능하게 했다. 본 논문에서는 GPU를 이용해서 Time-Variant 볼륨 데이터를 빠르게 가시화하고, 이렇게 개발한 GPU 볼륨 렌더링 프로그램을 사용자가 사용하기 편리하도록 사용자 친화적인 유저 인터페이스를 설계하고 구현하였다. 특히, 시간에 따라 동적으로 변화해야 하는 전이함수를 최대한 편리하게 생성할 수 있도록 전이함수 에디터에 중점을 두었다.

• Journal of Multimedia Information System
• /
• v.6 no.4
• /
• pp.239-244
• /
• 2019

With the development of Cyber-Physical Systems(CPS), several technologies such as automation control, automotive and intelligent house systems have been developed. To enable communication among various components of such systems, several wired and wireless communication protocols are used. The Controller Area Network(CAN) is one of such wired communication protocols that is popularly used for communication in automobiles and other machinery in the industry. In this paper, we designed and implemented a response time analysis system for CAN communication. The reliable data transfer among various electronic components in a significant time is crucial for the smooth operation of an electric vehicle. Therefore, this system is designed to conveniently analyze the response time of various electronic components of a CAN enabled system. The priority for transmission of the messages in the CAN bus is determined by the message identifier. As the number of nodes increases the transmission of low priority messages is delayed due to the existence of higher priority messages on the bus. We used Raspberry Pi3 and PiCAN2 board to simulate the data transfer for studying the comparative delay in low priority nodes.

• Journal of Korea Multimedia Society
• /
• v.16 no.4
• /
• pp.464-471
• /
• 2013

With the advance of wireless sensor networks, WMSN(Wireless Multimedia Sensor Networks) researches to transfers multimedia data have been studied actively. First of all, three basic protocols, End-to-end, Hop-by-hop, and Unreliable transmission method, are compared to transfer multimedia data using simulations. This paper presents an efficient protocol to transfer multimedia data by overhearing messages of nodes and by transmitting next packets during the unused time interval. The proposed method is verified its performance by simulations and experiments. The results shows that the transmission rate of the proposed method 22% higher than that of End-to-end protocol with half of transmission time. Also the performance of the proposed method is compared with that of PIGAB(Packet Interval Gap based on Adaptive Backoff).

• IEMEK Journal of Embedded Systems and Applications
• /
• v.14 no.5
• /
• pp.249-258
• /
• 2019

In the cyber-physical system, big data collected from numerous sensors and IoT devices is transferred to the Cloud for processing and analysis. When transferring data to the Cloud, merging data into one single file is more efficient than using the data in the form of split files. However, current merging and splitting operations are performed at the user-level and require many I / O requests to memory and storage devices, which is very inefficient and time-consuming. To solve this problem, this paper proposes kernel-level partitioning and combining operations. At the kernel level, splitting and merging files can be done with very little overhead by modifying the file system metadata. We have designed the proposed algorithm in detail and implemented it in the Linux Ext4 file system. In our experiments with the real Cloud storage system, our technique has achieved a transfer time of up to only 17% compared to the case of transferring split files. It also confirmed that the time required can be reduced by up to 0.5% compared to the existing user-level method.

• International conference on construction engineering and project management
• /
• 2022.06a
• /
• pp.375-381
• /
• 2022

Safety accidents are of concern during construction projects, even given the recent innovations in digital technologies. These projects remain focused on overcoming specific and limited applications on construction sites. For this reason, the development of an inclusive safety management system has become crucial. This study aims to build a Big Data platform to inform decisions on how to proactively eliminate worker hazards on construction sites. The platform consists of about 100,000 real records and a real-time monitored database featuring various safety indices, such as workers' altitudes, heart rates, and fatigability during construction, which are determined through various wearable devices. The data types are customized and integrated by a research team in accordance with the characteristics of a specific project using hypertext transfer protocol (HTTP). The results can be helpful as efficient tools to ensure successful safety management in complex construction situations. This study is expected to provide three significant contributions to the field, including real-time fatigability analysis and tracking of workers on-site; providing early GPS-based warnings to workers who might be accessing dangerous spaces or places; and monitoring the workers' health indices, based on details from 100,000 cases.

• Transactions of the Society of Information Storage Systems
• /
• v.3 no.1
• /
• pp.13-16
• /
• 2007

The purpose of this paper is real time tilt servo control of the holographic data storage system. Holographic data storage device is a next generation data storage device with high storage density, high transfer rate and short access time. This device is very sensitive to a disturbance due to the enormous storage density. As to the recording material changed disc type, the media continuously vibrates as the disc rotates. When disc rotates, deviation, eccentricity and unbalance disturbance are occurred. This disturbances cause disc tilt, finally reference beam does not illuminates to correct incidence angle. Therefore real time tilt servo control is essential. In this paper, the algorithm is proposed to make real time tilt detection in angle multiplexing of the holographic data storage system with an additional servo beam and the experiments are performed.