• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.6
• /
• pp.1149-1158
• /
• 2000

A radioisotope tracer experiment was carried out in the submerged fixed bioreactor of a dye wastewater treatment facility to evaluate the flow behaviors in the 6 compartments of the reactor and to find any possible factors which may affect to the efficiency of the process. Approximately 20mCi of $^{131}I$ was injected into the system as a tracer and 8 radiation detectors were placed in the 6 compartments and at the inlet and the outlet of the system to measure the change of the tracer concentration with time. Using the Perfect Mixers in Series Model the measured data were analyzed to calculate the mean residence time and the characteristic parameters of the flow in the system. The mean residence time of the system was calculated as 17 hours which is 76% of the designed MRT(22.3hr). Among the 6 compartments, the first compartment doesn't show the characteristic of perfect mixer, whereas, the other 5 compartments are working as perfect mixers. The output response of the first compartment is fit well with the simulated output of a model which consists of a perfect mixer with an exchange volume. It indicates that a quarter of the tank volume is working as a dead volume or an exchange volume. From the measured residence time distributions in each compartment, the appropriate sampling times after the change of operational condition of the electron beam accelerator were evaluated.

• Asian-Australasian Journal of Animal Sciences
• /
• v.22 no.5
• /
• pp.686-693
• /
• 2009

A 21- to 42-day feeding study was conducted in Ross male broilers to evaluate the use of dried bakery product (DBP) and the influence of adding fat at different points in the manufacturing process. Six dietary treatments were formulated using a factorial arrangement (3${\times}$2 design) with three levels of fat in the mixer (high: 4.8%, medium: 3.8% and low: 2.8%) with or without DBP (0 and 7%). Additional fat was sprayed on pellets in a post-pelleting liquid application to bring the fat content to a similar level in all diets. Data on pellet quality (before and after post-pelleting fat addition), broiler performance, nutrient digestibility and organ weights were studied. Pellets made with DBP showed higher hardness values when measured before post-pelleting fat addition (p<0.001), although DBP did not affect final pellet hardness or durability. Higher post-pelleting hardness and durability were shown by diets to which a lower level of fat had been added in the mixer (p<0.001). In general, post-pelleting fat application improved durability (p<0.05). However, broiler performance and ileal digestibility were not affected by any of the factors tested. Dietary treatments had a significant but variable effect on carcass yield (p<0.01), although there were no differences among treatments regarding breast and leg yield, abdominal fat or organ weights. The results indicate that up to 7% DBP could be used in the broiler diet without impairing performance, ileal digestibility or organ weights. The place or point of fat addition in the manufacturing process has a strong influence on pellet quality.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.3
• /
• pp.1-6
• /
• 2008

A dual band I/Q modulator which converts baseband input signals to 2.4GHz or 5GHz RF output has been proposed. The dual band I/Q modulator for 2.4GHz and 5GHz wireless LAN applications consists of $90^{\circ}$ phase shifter and wideband mixer. The I/Q modulator showed 15dB conversion loss at 2.4GHz and 16dB conversion loss at 5GHz. The sideband suppression is about 15dBc at 2.4GHz and 16dBc at 5GHz. Measured data shows 8.5% EVM at 2.4GHz, and 10% EVM at 5GHz for QPSK with symbol rate of 11Mbps. A carrier rejection is about 40dBc at 2.4GHz/5GHz band, and the I/Q modulator satisfied the output wireless LAN spectrum mask with baseband input signal.

• Applied Chemistry for Engineering
• /
• v.25 no.1
• /
• pp.58-65
• /
• 2014

In this work, we constructed the sulfur-solidified materials using coal bottom ash from four thermal power stations in Korea and investigated their practical data for the production of industrial construction compounds. To manufacture the sulfur-solidified materials, we used a continuous mixer with the uniaxial screw-type. Also, coal bottom ash was used as a fine aggregate below 1.2 mm because of the operation characteristics for the continuous mixer. When the sulfur-solidified materials were produced with diverse sulfur concentrations (15, 20, 25, 30 wt%), compressive strength properties were analyzed. In addition, when the coal bottom ash was used with a high calcium oxide content, crack was found in the test product and pH of submerged liquid was above 12. These experimental results could be effectively applied to the recycling technology of coal bottom ash.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.9 no.6
• /
• pp.1277-1281
• /
• 2005

FPGA has been widely used in communication system. In this paper, we made 10 layers PCB on protection of signal noise and data lose with FPGA. We analyzed about change of the data transmission speed and length according to input frequency. The length of transmission line from FPGA's output-pin to output-port on PCB board is 13cm and extended lengths for test are 30cm, 60cm and 10cm. We knew that data can be stably transmitted to 100Mbps at transmission line length of 30cm.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.55 no.6
• /
• pp.286-295
• /
• 2006

This paper presents a design of a real-time software GPS receiver which runs on a PC. The software GPS receiver has advantages over conventional hardware based receivers in terms of flexibility and efficiency in application oriented system design and modification. In odor to reduce the processing time of the software operations in the receiver, a shared memory structure is used with a dynamic data control, and the byte-type IF data is processed through an Open Multi-Processing technique in the mixer and integrator which requires the most computational load. A high speed data acquisition device is used to capture the incoming high-rate IF signals. The FFT-IFFT correlation technique is used for initial acquisition and FLL assisted PLL is used for carrier tracking. All software modules are operated in sequence and are synchronized with pre-defined time scheduling. The performance of the designed software GPS receiver is evaluated by running it in real-time using the real GPS signals.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.7
• /
• pp.4930-4935
• /
• 2015

In the actual research fields, the studies for applications of 180 MPa ultra high performance concrete (UHFRCC) to compressive members are limited due to its very high compressive strength. In this study, in order to find its practical use, UHPC was producted by using twin-shaft mixer batch plant. Also, to get basic research data for the design specification of UHPC compressive members, a series of draft experiments, including short columns with square and circular sections, were performed and its failure modes and behaviors were assessed.

• Journal of Environmental Science International
• /
• v.6 no.2
• /
• pp.133-139
• /
• 1997

The solvent extraction method was applied on the wastewater produced during malonate(malonic acid esters) process to recover cobalt. DEHPA and PC88A were used as organic solvent From separation funnel experiment(batch experiment), the effects of vari- ous parameters (pH, cobalt concentration, reaction rate, and stripping temperature) on solvent extraction were examined and these data were used to derive equilibrium curve. A mixer-settler experiment (continuous experiment) of bench scale was also carried out for the plant construction and a Mccabe-Thiele diagram was obtained. The results of these experiments indicate that cobalt is recoverable above 99 oyo and that its purity as cobalt sulfate Is higher than 99.9 wt%.

• Journal of Korea Foundry Society
• /
• v.7 no.3
• /
• pp.199-206
• /
• 1987

This paper presents experimental data for the computerization of green sand control. The results can be summarized as follows: 1. To obtain the proper compactability at the mixer, the addtion of moisture is far more efficient than the control of mixing time or addtion of clay. 2. The log R(% clay/% moisture) vs. log compactability curve moves upward as the amount of clay increases and moves downward as the amount of seacoal, dead bentonite or coked seacoal increases. 3. The ratio of dead to initial clay amount or coked to initial seacoal amount is changed according to sand to metal ratio, mainly, and according to pouring temperature, partly, at a shake out time of 12hrs.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2003.05a
• /
• pp.595-600
• /
• 2003

This paper presents the applicability of low caloric synthetic gas from coal gasification to a gas engine system. A commercial LPG engine is modified to use the low caloric synthetic gas from coal gasification as the gas engine fuel. The modification is focused on the fuel supplying system, which includes air flowrate adjusting orifice, gas mixer, vaporizer, preheater, regulators, and fuel tank. The electrical system and others for the alternative fuel are also redesigned and replaced. From the results of engine performance data, we have demonstrated that the engine modified by using coal gasification gas is well operated from idle to wide open throttle conditions although the engine power is somewhat reduced relative to LPG fueled engine. This paper addresses the need to determine the practical potential for such a concept and to identify further research and development efforts that may be necessary.