• 한국생산제조학회지
• /
• 제9권2호
• /
• pp.125-137
• /
• 2000

In this paper we propose a new approach to the development of the automatic vision system to examine and repair the steam generator tubes at remote distance. In nuclear power plants workers are reluctant of works in steam generator because of the high radiation environment and limited working space. It is strongly recommended that the examination and maintenance works be done by an automatic system for the protection of the operator from the radiation exposure. Digital signal processors are used in implementing real time recognition and examination of steam generator tubes in the proposed vision system. Performance of proposed digital vision system is illustrated by simulation and experiment for similar steam generator moldel.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.606-609
• /
• 1995

To stabilize a satellite, a spin stabilization method is used for attitude control. The spin stabilization uses the centrifugal force of a pendulum damper which is tilted long boom, to stabilize the unstable satellite. In this paper, an inverted pendulum system is implemented which is similar to the spin stabilization method. Study on the velocity of the rotation axis and the inverted pendulum's angle stability is shown. We designed a controller using a 32bit TMS320C31 DSP for the CPU and also performances by PLD control and Sliding Mode Control is compared.

• 전기학회논문지
• /
• 제56권5호
• /
• pp.892-897
• /
• 2007

This paper presents the output filter design and the output characteristic analysis by cut-off frequency set up of the LCR filter on NPC multi-level inverter with trap-filter. The single-phase NPC three-level inverter operates at low switching frequency. The proposed LC trap filter is comprised of a conventional LCR output filter, by using LC trap filter the need for high damping resistor and low LC cut-off frequency is eliminated. Also. low damping resistor is increased the output filter system. The multilevel inverter system used NPC type inverter in proper system for high power application and controller is used DSP(TMS320C31). The effectiveness of proposed system confirmed the validity through SPICE simulation and experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.1172-1175
• /
• 2001

Recently, vector control without a speed sensor for an inverter induction motor system has been developed. In this paper describes the vector control system estimates rotor speed based on FMRAS(Flux Model Reference Adaptive System). Because of improving the initial condition and drift problem by pure integrator is eliminated, we can be expected to rapid responsibility of the speed estimation. The stability of speed estimator is proved on the basis of hyperstability theory. Proposed control system used TMS320C31 DSP for high speed processing. The effectiveness of the proposed system is verified by simulation and experimental results. This result shows that the highly characteristic speed estimation and robust character of load regulation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 A
• /
• pp.191-193
• /
• 2000

In this paper, being different from traditional methods, we design digital protective relay which can be applied to power management and control systems of not only small and medium but also a large scale plants. The digital protective relay was designed with DSP CPU(TMS320C31) to protect and measure more quickly and precisely. We will present test result which it performed according to the standards of Korea Electrical Manufactures Cooperative to prove the faculties of digital protective relay. The test result on the basis of KEMC1120 and IEC60255, show that the operation time error of the digital motor protection relay is improved within ${\pm}5%$.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.848-851
• /
• 2005

This paper proposes a design of IIR notch filter with modified pole placements. The pole angle is derived from quadratic programming to find the appropriate pole position on the unit circle in z-plane in order to achieve the symmetry of the amplitude response. The simulation results are shown when compared with the conventional design technique. Moreover, it uses the TMS320C31 DSP chip for hardware implementation. Finally, the hardware implementation can be applied to removal of ECG baseline wander and elimination of AC power line interference in ECG signal.

• 산업기술연구
• /
• 제22권B호
• /
• pp.185-190
• /
• 2002

This paper describes a design of an induction motor control system using a 2 degree-of-freedom PI controller to compensate the effects of disturbance without degrading tracking performance. On the basis of vector control principle, the control system is simulated by using the ACSL and implemented on a DSP system(TMS320C31). In designing the 2 DOF controller, we can tune the performance of either the tracking or disturbance rejection independently without affecting the other. With the experimental results, the 2 DOF controller has shown a better performance in command tracking and disturbance rejection than a conventional PI controller.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 B
• /
• pp.976-978
• /
• 1999

Recently PWM invertor is broadly used for control of induction motor. The invertor is able to generate sin wave current from high speed switching power device such as IGBT. However the invertor is disturbed by dead time inevitably needed to prevent a short of the DC link voltage, and the dead time mainly causes distortions of the output current. In this Paper the dead time compensation method which corrects the voltage error from dead time, and Min Max algorithm enlarging the operating voltage of PWM were Proposed. This method can be implemented by software programming without any additional hardware circuit. The proposed algorithms were implemented by DSP(TMS320C31, 40MHz) and FPGA(QL2007, Quick Logic) described in VHDL. and applied to 3 phase induction motor(2.2 KW) to show the superior performance

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.91.3-91
• /
• 2002

This paper describes a design of an induction motor control system for industrial sewing machines. On the basis of vector control principle, the control system is simulated by using the ACSL, implemented on a DSP(TMS320C31).A space vector modulation is used as the inverter switching strategy. For the application of industrial sewing machines, A fast acceleration (deceleration) and removal of velocity ripples are required, because a sewing quality and sewing machines life time depends on these characteristics. The designed control system has fast dynamic characteristics and small speed vibration. The result is applied to the industrial sewing machine and result are shown.

• 제어로봇시스템학회논문지
• /
• 제4권5호
• /
• pp.658-665
• /
• 1998

In this paper, we propose a new approach to the development of the automatic vision system to examine and repair the steam generator tubes at remote distance. In nuclear power plants, workers are reluctant of works in steam generator because of the high radiation environment and limited working space. It is strongly recommended that the examination and maintenance works be done by an automatic system for the protection of the operator from the radiation exposure. Digital signal processors are used in implementing real time recognition and examination of steam generator tubes in the proposed vision system. Performance of the proposed digital vision system is illustrated by simulation and experiment for similar steam generator model.