• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.10
• /
• pp.1061-1070
• /
• 2002

In this paper, we present a performance analysis of the smart antenna test-bed operating in a IS2000 1x through a test-bed that has been implemented on a DSP(TMS320C6711) board. The test-bed consists of a PC (for generating the RX data), beam-former(i.e., a stand-alone PCB for weight computation), and an interfacing module. The performance improvements compared to a normal base station system consisting of a single antenna are shown in terms the BER(bit error rate) in the wide-band CDMA channel.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.10 no.1
• /
• pp.73-79
• /
• 2014

In this study, the unmanned vehicle to develop a preliminary step, we were facilities for Automated Guided Vehicle (AGV) simulator is designed and implemented. Industry is increasingly the more advanced automation and management systems need to be efficient. These studies are at least 24-hour continuous unmanned vehicles and personnel can result in reduction of labor costs. In addition, safety accidents can be minimized in the industry as an effect of intelligent AGV is essential. This study is the initial step for the development of AGV. manufactured simulator to Simulation and drives the performance of the system is evaluated. The configuration of the simulator, ultrasonic sensors, infrared sensors, and using the obstacle were to follow a given path. In addition, two-way communication between the host computer and the main processor that was. communication method that IEE802.11 meets the standard is applied to high-speed wireless LAN systems, each of the sensor information is calculated. AGV having a drive shaft 4 of the four wheels are respectively independent structure. AGV's main processor is driven using a high-performance DSP, and the controller controls the steering device of the load could be significantly reduced.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2162-2172
• /
• 2016

This paper presents a Direct Torque Control (DTC) strategy for the five-phase induction motor driven by a three-level five-phase inverter in order to improve the performance of the five-phase induction motor. In the proposed DTC technique, only 22 voltage vectors out of 243 available voltage vectors in a three-level five-phase inverter are selected and are divided in 10 sectors each with a width of $36^{\circ}$. The four different DTC combinations (DTC-I, II, III and IV) for a three-level five-phase induction motor drive are investigated for improving the performance of five-phase induction motor. All four of the DTC strategies utilize a combination of the same large and zero voltage vectors, but with different medium voltage vectors. Out of these four techniques, DTC-II gives the best performance when compared to the others. This DTC-II technique is analyzed in detail for improvements in the performance of five-phase induction motor in terms of torque ripple, x-y stator flux and Total Harmonics Distortion (THD) of the stator phase current when compared to its two-level counterparts. To verify the effectiveness of the proposed three-level five-phase DTC control strategy, a DSP based experimental system is build. Simulation and experimental results are provided in order to validate the proposed DTC technique.

• ETRI Journal
• /
• v.39 no.5
• /
• pp.707-717
• /
• 2017

This paper presents a novel generalized quadrature spatial modulation (GQSM) transmission scheme using antenna grouping. The proposed GQSM scheme combines QSM and conventional spatial multiplexing (SMux) techniques in order to improve the spectral efficiency (SE) of the system. Analytical and simulation results show that the proposed transmission scheme has minimal losses in terms of the average bit error probability along with the advantage of an increased SE compared with previous SM and QSM schemes. For the case studies, this advantage represents a reduction of up to 81% in terms of the number of required transmit antennas compared with QSM. In addition, a detection architecture based on the ordered successive interference cancellation scheme and the QR decomposition is presented. The proposed QRD-M adaptive algorithm showed a near-maximum-likelihood performance with a complexity reduction of approximately 90%.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.4
• /
• pp.388-396
• /
• 2005

SRM has not been put into practical applications widely because of its large torque ripple, acoustic noise and low power factor. In addition, a traditional position sensor is needed for the drive control. So we propose an improved sensorless drive method of Switched Reluctance Motors using impressed voltage pulses. Conventional impressed voltage pulse method has a problem of phase delay because of low-pass filter. So in this paper we propose an unproved sensorless driving method based on the impressed voltage pulse using new pulse-shift circuit technique that overcomes the phase delay and start-up problem. Proposed method is implemented in a simple analog circuit instead of using an expensive DSP.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.11 no.4
• /
• pp.349-360
• /
• 2006

Controller for doubly-fed induction-type wind generation system should be designed with mechanical power on blade. The controller in this paper consists of upper level controller and lower level controller. The upper level controller determines operating modes according to mechanical input power and calculates proper reference values. There are 4 operating modes - minimum speed control, variable torque control, torque limit control and idle mode. The lower level controller performs current regulated PWM control of rotor-side converter and grid-side inverter. A wind turbine simulator is implemented using doubly-fed induction-type generator and DSP based back-to-back converter to verify the performance of designed controller experimentally.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.6
• /
• pp.128-135
• /
• 2004

The author present a modified multi-loop algorithm including feedforward for controlling a 55kW step down chopper in the power supply of Maglev. The control law for the duty cycle consists of three terms. The first is the feedforward term. which compensates for variations in the input voltaga. The second term consists of the difference between the slowly moving inductor current and output current. The third term consists of proportional and integral terms involving the perturbation in the output voltage. This perturvation is derived by subtracting the desired output voltage from the actual output voltage. The proportional and integral action stabilizes the system and minimizes output voltage error. In order to verify the validity of the proposed multi-loop controller, simulation study was tried using Matlab simulink

• Proceedings of the KIPE Conference
• /
• 2015.07a
• /
• pp.401-402
• /
• 2015

In this paper a direct cell-to-cell charge balancing circuit which can transfer the charge from any cell to any cell in the battery string is introduced. In the proposed topology the energy in the high voltage cell is transferred to the low voltage cell through the simple operation of a dc-dc converter to get fast equalization. Furthermore, the charge equalization can be performed regardless of the battery module operation whether it is being charged, discharged or relaxed. The monitoring circuit composed of a DSP and a battery monitoring IC is designed to monitor the cell voltage and protect the battery. In order to demonstrate the advantages of the proposed topology, a prototype circuit was designed and applied to 12 Lithium-Ion battery module. It has been verified with the experiments that the charge equalization time of the proposed method was shortest compared with those of other methods.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1241-1242
• /
• 2007

전세계가 고유가 시대로 들어서면서 각국은 에너지 확보에 전력을 기울이고 있다. 이에 대체 에너지 개발이 미래의 중요한 과제로 여겨지고 있다. 본 연구에서는 결정질 실리콘 태양전지의 대안으로 주목받고 있는 염료감응형 태양전지를 다루어 보았다. 유효면적 $8cm^2$의 염료감응형 태양전지의 직병렬 조합을 이용하여 DSSC 모듈을 만들어 얻은 출력을 전력변환 시킴으로써 상용전원을 얻고자 하였다. 염료감응형 태양전지모듈을 만들기 위해 먼저 DSSC의 단위 셀을 최적화 시키고 이를 실제 광원에서 다양한 직병렬 연결 시도 끝에 모듈로부터 약 5.7V, 3A의 출력을 얻을 수 있었다. 이를 Boost converter를 이용하여 전압을 12V까지 승압하고 이 출력을 고속 스위칭 소자인 MOSFET을 이용하여 스위칭한 Push-pull converter에서 DC 310V까지 승압시켰다. 그리고 그 출력을 DSP를 이용한 20[kHz]의 PWM신호를 만들어 제어한 결과, AC 220V의 상용전원을 얻었다. 그리고 이 전원을 부하에 연결하여 그 동작 특성을 연구하였다.

• Proceedings of the KIEE Conference
• /
• 2003.11c
• /
• pp.987-990
• /
• 2003

산업현장에서의 인터넷환경 및 원격 제어를 위한 시스템 개발에서 신뢰성이 있고 경제적이며 지능적인 Power Supply가 요구되고 있다. 최근 통신시스템의 Power Supply는 수 kA이상의 출력전류를 가지고 있으며 최소 10개 이상의 모듈로 이루어져 있다. High-End 서버 시스템과 같이 수백 개의 마이크로프로세서를 내장한 시스템은 수십 kW의 전력을 소모한다. 이들이 사용하는 Power Supply는 별도의 시스템 제어기와의 통신으로 시스템에서 발생하는 발열, 소모전력, Total Harmonic Distortion (THD)에 대한 정보를 바탕으로 시스템이 갖는 각각의 Module에 대해 효과적이고 신뢰성 있는 전력공급을 하여야 만다. Distributed Power System (DPS)에서 가장 중요만 역할을 담당하는 Power Factor Correction (PFC) AC-DC Converter의 디지털 제어는 시스템 제어기와의 통신능력을 충분히 고려하면서 DPS를 위한 적합한 솔루션을 제공할 것이다. 본 논문에서는 Digital Signal Processor (DSP)를 사용하여 PFC 제어에 필요한 전파정류전압, 입력전류, 출력전압을 계측하여 역률개선과 THD의 저감을 위한 전류의 추종을 제어하면서 이들 제어기에서의 파라미터를 PC를 통해 모니터하여 최근의 추세를 만족시킬 수 있는 시스템을 구현할 수 있을 것으로 사료된다.