• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.6C
• /
• pp.498-504
• /
• 2008

In this paper, an efficient hardware platform for the digital signal processing for OFDM Communication systems is presented. The hardware platform consists of a single FPGA, two DSPs with 8000 MIPS of maximum at 1 GHz clock, 2-channel ADC and DAC supporting maximum 125 MHz sampling rate, and flexible data bus architecture, so that a wide variety of baseband signal processing algorithms for practical OFDM communication systems may be implemented and tested. The IEEE 802.16 software modem is also presented in order to verify the effectiveness and usefulness of the designed platform.

• Journal of Broadcast Engineering
• /
• v.13 no.4
• /
• pp.452-462
• /
• 2008

In this paper, we address issues associated with the real-time implementation of the MPEG-1/2 Layer-II (or MUSICAM) and MPEG-4 ER-BSAC decoders for Digital Multimedia Broadcasting (DMB) on TMS320C64x+ that is a fixed-point DSP processor with a clock speed of 330 MHz. To achieve the real-time requirement, they should be optimized in different steps as follows. First of all, a C-code level optimization is performed by sharing the memory, adjusting data types, and unrolling loops. Next, an algorithm level optimization is carried out such as the reconfiguration of bitstream reading, the modification of synthesis filtering, and the rearrangement of the window coefficients for synthesis filtering. In addition, the C-code of a synthesis filtering module of the MPEG-1/2 Layer-II decoder is rewritten by using the linear assembly programming technique. This is because the synthesis filtering module requires the most processing time among all processing modules of the decoder. In order to show how the real-time implementation works, we obtain the percentage of the processing time for decoding and calculate a RMS value between the decoded audio signals by the reference MPEG decoder and its DSP version implemented in this paper. As a result, it is shown that the percentages of the processing time for the MPEG-1/2 Layer-II and MPEG-4 ER-BSAC decoders occupy less than 3% and 11% of the DSP clock cycles, respectively, and the RMS values of the MPEG-1/2 Layer-II and MPEG-4 ER-BSAC decoders implemented in this paper all satisfy the criterion of -77.01 dB which is defined by the MPEG standards.

• International Journal of Internet, Broadcasting and Communication
• /
• v.11 no.2
• /
• pp.27-30
• /
• 2019

Factory monitoring systems are gaining importance in wide areas of industry. Especially, there have been many efforts in implementation of vibration measurement and analysis for monitoring the status of rotating machines. In this paper, a digital signal processor (DSP) based monitoring system dedicated to the vibration monitoring and analysis on rotating machines is discussed. Vibration signals are acquired and processed for the continuous monitoring of the machine status. Time domain signals and fast Fourier transform (FFT) are used for vibration analysis. All of the signal processing procedures are done in the DSP to reduce the production and maintenance cost. The developed system could also provide remote and mobile monitoring capabilities to operator via internet connection. This paper describes the overview of the functional blocks of the implemented system. Test results based on signals from small-size single phase motors are discussed for monitoring and defect diagnosis of the machine status.

• Journal of Satellite, Information and Communications
• /
• v.12 no.2
• /
• pp.1-10
• /
• 2017

In this paper we propose three existing reflection removal algorithms and one proposed algorithm to estimate accurate targets in near field using IR-UWB (Impulse-Radio Ultra Wideband) radar. The received signal includes unnecessary reflected wave signals to the target signal. A reflective cancellation algorithm was used to remove unnecessary signals and estimate only the correct target signal. The location of the targets is estimated in real time with one transmitting antenna and one receiving antenna. In order to overcome the disadvantages of the existing three reflection removal algorithms, we propose a new reflection removal algorithm and estimate the most accurate target. Also we used DSP(Digital Signal Processor) to install the external mounting of vehicles. This paper will contribute to the study of the future reflections.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.8 no.10
• /
• pp.3475-3489
• /
• 2014

Here we present a simple flame detection method for an infrared (IR) thermal camera based real-time fire surveillance digital signal processor (DSP) system. Infrared thermal cameras are especially advantageous for unattended fire surveillance. All-weather monitoring is possible, regardless of illumination and climate conditions, and the data quantity to be processed is one-third that of color videos. Conventional IR camera-based fire detection methods used mainly pixel-based temporal correlation functions. In the temporal correlation function-based methods, temporal changes in pixel intensity generated by the irregular motion and spreading of the flame pixels are measured using correlation functions. The correlation values of non-flame regions are uniform, but the flame regions have irregular temporal correlation values. To satisfy the requirement of early detection, all fire detection techniques should be practically applied within a very short period of time. The conventional pixel-based correlation function is computationally intensive. In this paper, we propose an IR camera-based simple flame detection algorithm optimized with a compact embedded DSP system to achieve early detection. To reduce the computational load, block-based calculations are used to select the candidate flame region and measure the temporal motion of flames. These functions are used together to obtain the early flame detection algorithm. The proposed simple algorithm was tested to verify the required function and performance in real-time using IR test videos and a real-time DSP system. The findings indicated that the system detected the flames within 5 to 20 seconds, and had a correct flame detection ratio of 100% with an acceptable false detection ratio in video sequence level.

• Journal of the Korean Institute of Telematics and Electronics S
• /
• v.35S no.10
• /
• pp.19-26
• /
• 1998

In this paper, we studied the design and implementation of fading compensation systems at aspects of narrowband mobile communication using TTIB SSB. The mobile radio channel with multipath fading places fundamental limitations on the performance of wireless communication systems. The multipath fading is compensated using pilot tone in TTIB SSB. The TTIB transceiver was implemented using the prevailing digital signal processing (DSP) techniques and compensation for the multipath fading was incorporated in the receiver in the form of DSP algorithm. In order to evaluate fading compensation performance in TTIB transceiver, we first used computer simulation. In the simulation results, we found that the TTIB transceiver could compensate for the multipath fading as expected. Second, we carried out some experiments on TTIB transceiver implementation with DSP boards and later with hardwares including RF circuits with center frequency of 145MHz. Through these experiments, we found that fading compensation performance in TTIB transceiver was almost as good as that obtained from simulation.

• 한국정보통신설비학회:학술대회논문집
• /
• 2009.08a
• /
• pp.117-120
• /
• 2009

In this paper, a CR(Cognitive Radio) based on SDR(Software Defined Radio) is the technology combined a method selecting available frequency by recognizing surroundings with a learning algorithm continuously updating basic functions for communication and various environment parameters. Recently, as increasing demands with development of wireless communication service, CR is in the spotlight as technology using frequency resource efficiently. In order to apply CR system to the terminal and implement it, the research field to be preceded can be divided large as a hardware part and a software part. It can be also divided into RF processing and digital signal processing in the hardware part. In this paper, we look over preceding techniques required for applying CR system to the terminal, and research the forms of the terminal when they practically apply to the terminal.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.6
• /
• pp.944-953
• /
• 1990

This paper describes design and implementation of a real-time high-precision vision system for an automation of SMT(surface mounting technology ). Also, a part inspection algorithm which calculates the position and direction of SMD(surface mounted device) accurately and performs the ruling using those information are presented, and a parallel processing technique for implementing those algorithms is also described. For a real-time implementation of iage acquisition and processing, several hardware modules, namely, multi-functional A/D-D/A board, frame memory board are developed. Particularly, a PE (processing element) board which employs the DSP56001 DSP (digital signal processor) is developed for the purpose of concurrent processing of part inspection algorithms. A stand-alone vision system is built by integration of the developed hardware modules and related softwares.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.21 no.6
• /
• pp.27-33
• /
• 1984

This paper is an experimental gaudy on the digital hardware implementation of the R2-MF Receiver for 32 channel configurations used in signalling systems between ESS. There are many methods to detect MF signal by DSP techniques, but the requirement for MF detection needs not sharp frequency response, needs only decision about some specific frequencies exist or not at discrete frequency sampling points. The hardware used to implement this algorithm is Am 2900 series "bit-slice microprocessor" chips based on the microprogramming techniques for real time signal processing. And we used the additional Z-80A processor chips for the system control and the decision about which is the right MF signal from the detected MF spectrums. Hence we could enhance the flexibilities of the hardware and the software, this leads that this system is well suits for signalling systems used in TDM ESS.n TDM ESS.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.9
• /
• pp.1125-1130
• /
• 2014

In this paper, we propose a sound reception system against surrounding noise for ships based on digital signal processing technologies. In order to suppress unwanted surrounding noises, a digital band-pass filter is designed, which the pass-band of the filter is between 70Hz to 820Hz. Also, we develope a sound direction indicating algorithm with 4 microphones. After filtering the audio signals from 4 microphones, the developed sound direction indicating algorithm can indicate 8 directions. In addition, we implement prototype board for the sound reception using a digital signal processor chip and audio codecs, and verify the proposed algorithm.