• 한국응용과학기술학회지
• /
• 제34권1호
• /
• pp.12-24
• /
• 2017

현재 국내 엔진오일-윤활유가 배출가스에 미치는 영향에 대한 연구가 미비한 실정이며 그 실험 방법 또한 확립되어 있지 않다. 이에 엔진을 이용한 윤활유 성상 변화가 PM(Particulate Matters) 배출에 미치는 영향 평가방법을 수립하여 윤활유의 성상 및 열화가 자동차 성능과 환경성에 미치는 영향을 연구하고자 한다. 윤활유 소모 및 연소로 인한 DPF(Diesel Particulate Filter) 및 후처리 장치에 미치는 영향을 평가하는 것이 중요하며, 특히 DPF의 재생과정에서 생성되는 PM(Particulate Matters)과 Ash가 DPF에 미치는 장기적인 영향과 내부 변형 및 내구성에 대한 평가와 연구가 필요하다. 본 연구에서는 정형화 되지 않은 시험모드를 개발하였으며, 내구시험결과 High SAPs의 경우 Low SAPs(Sulfated Ash, Phosphorus and Sulfuate)보다 DPF내 Ash의 축적량이 많은 것을 확인하였으며, EGR(Exhaust Gas Recycling)의 Fouling 현상 가속화에 영향을 미칠 것으로 확인하였다. 본 연구결과물을 토대로 윤활유의 기유, 첨가제, 열화 등에 따른 엔진 및 차량의 성능과 배출가스 특성을 기술정책 자료로서 활용하도록 방향을 도모하고 시험 방법을 확립하고자 한다.

• 한국결정성장학회지
• /
• 제31권3호
• /
• pp.116-126
• /
• 2021

코디어라이트(Mg₂Al₄Si₅O₁₈) 하니컴 세라믹스의 대표적 응용분야는 자동차 배기가스 정화용 필터(diesel particulate filter(DPF))이다. 천연광물, 조공제, 유기바인더를 혼합한 슬러리를 압출하여 DPF용 하니컴 코디어라이트를 성형한 후 980~1450℃ 범위에서 소결하였다. 소결온도에 따른 결정상(indialite, cordierite, cristobalite, alumina, spinel, mullite, pro-enstatite)의 형성과정을 XRD Rietveld 정밀화법을 이용하여 정량분석 하였다. 동시에, 세라믹 에칭(etching) 방법으로 소결 시료 표면의 비정질상을 제거한 후 SEM/EDS법을 사용하여 결정상들의 형상과 조성을 확인하였다. 이들 결과로부터 DPF 하니컴에서 결정상 형성 과정을 명확히 밝힐 수 있었다. 또한, DPF 하니컴의 소결온도에 따른 열팽창계수(linear coefficient of thermal expansion, CTE) 변화를 분석하였고, 결정상의 정량분석결과를 바탕으로 계산된 CTE와 비교하였다. 소결된 DPF 하니컴 내의 결정상들이 CTE 특성에 미치는 영향을 고찰하였다.

• 자동차안전학회지
• /
• 제10권3호
• /
• pp.27-31
• /
• 2018

The People have a bad perception about diesel vehicle because of serious air pollution, increase fine dust and global vehicle company's diesel gate. Starting the project in 2005, Ministry of Environment has been supporting that is exhaust gas reduction devices (DPF) on diesel vehicles in the metropolitan area. During the period of 2017.01.01 to 2017.12.31, 10,030 diesel vehicles installed exhaust gas reduction devices (DPF). Among them, 9,921 diesel vehicles that they have sufficient data for analysis were analyzed amount of particulate matter reduction before and after exhaust gas reduction devices (DPF) was installed. Opacity smoke meter measures the concentration of particulate matter. So concentration of particulate matter was converted into a mass unit, and then calculated the total amount of reduced particulate matter. It was estimated that social benefits is costs required to remove it from the total amount of particulate matter.

• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.68-76
• /
• 2006

The minimization of maximum DPF wall temperature and the fast Light-off during regeneration are the targets for the high durability of the DPF system and the high efficiency of regeneration. In order to predict transient thermal response of DPF, one-channel numerical modeling has been adopted. The effect of the ratio of length to diameter(L/D), cell density, the amount of soot loading on temporal thermal response and regeneration characteristics has been numerically investigated under two different running conditions: city driving mode and high speed mode. The results indicate that the maximum wall temperature of DPF increase with increasing 'L/D' in 'High speed mode'. For 'City driving mode', the maximum wall temperature decreases with increasing 'L/D' in the range of $'L/D{\geq}0.6'$. The maximum temperature decreases with increasing cell density because heat conduction and heat capacity are increased. It is also found that the effect of amount of soot loading on light-off time is negligible.

• 한국자동차공학회논문집
• /
• 제14권6호
• /
• pp.127-136
• /
• 2006

Prediction of diesel particulate filtration is typically made by virtue of modeling of particulate matter(PM) collection. The model is closed with filtration parameters reflecting all small scale phenomena associated with PM trapping, and these parameters are to be traced back by inversely analyzing large-scale empirical data-the pressure drop histories. Included are soot cake permeability, soot cake density, soot density in the porous filter wall, and percolation constant. In the present study, a series of single channel DPF experiment is conducted, pressure histories are inversely analyzed, and the essential filtration parameters are deducted by DPF filtration model formulated with non-linear description of soot cake regression. Sensitivity analyses of model parameters are also made. Results showed that filtration transients are significantly altered by the extent of percolation constant, and the soot density in the porous filter wall is controlling the filtration qualities in deep-bed filtration regime. In addition, effect of soot particle size on filtration quality is distinct in a period of soot cake regime.

• 한국자동차공학회논문집
• /
• 제18권1호
• /
• pp.131-138
• /
• 2010

Because real flow of engine exhaust is very hot and highly transient, it may cause thermal and inertial loads on catalyzed filters in DPF. Transient and detailed flow and thermal simulations are necessary in this field. To assess the importance of time dependent phenomena, typical cone-type configuration such as an underbody DPF is selected for steady and transient analysis. User defined functions of FLUENT by sinusoidal inlet velocities are written and integrated with main solver for realistic simulation. Also, 4-cylinder and 6-cylinder engines for 3,000 L class are considered for the dynamic exhaust effect of engine type. Key parameters to understanding of catalyst performance and durability issues such as flow uniformity index and peak velocity are investigated. Also, pressure drop for engine power are considered. From the simulation results for three different cases, proper approach is recommended.

• 한국자동차공학회논문집
• /
• 제16권6호
• /
• pp.168-175
• /
• 2008

In-use light duty diesel vehicles are considered as one of major sources of particulate emissions in many cities, and the start of the retrofit program for the light duty diesel vehicles is expected in near future in Korea. One of the problems of the retrofit of the light duty diesel vehicles is that the exhaust gas temperature is too low to apply passive regeneration DPF systems. This study introduces a catalytic combustor as a new active DPF regeneration technology. This study shows the principle and characteristics of DPF regeneration by the catalytic combustor and suggests it's proper control method for better regeneration.

• 한국분무공학회지
• /
• 제23권2호
• /
• pp.74-80
• /
• 2018

Emission characteristics of regulated pollutants (CO, NOx, HC and PM) and hazardous air pollutants (HAPs) from diesel heavy duty trucks equipped with EGR+pDPF and SCR for Euro 5 emission standards were investigated using a chassis dynamometer. In the case of regulated pollutants, diesel heavy duty trucks with EGR+pDPF emitted 79% less CO than those with SCR. Also, those with the SCR emitted 36% less NOx than those with the EGR+pDPF. The results of VOCs have show that alkanes emissions for heavy duty trucks with the EGR+pDPF and the SCR have been higher than alkenes, cycloalkanes and aromatics. In the case of individual VOCs, the highest of propene emissions for 11.3~16.1% occupied. For aromatics group, benzene emissions are the highest percentage for 4.4~15.5%. In the future, the results of present study will provide basic data to set up HAPs emissions inventory for mobile source.

• 한국안전학회지
• /
• 제23권5호
• /
• pp.7-14
• /
• 2008

The temperature distribution in a surface of diesel particulate filter(DPF) was measured using an infrared temperature camera. In order to regenerate the DPF, five partitioned electric heaters were used for heating the ceramic filter. The five partitioned heaters were switched on/off with some time interval one the other. The surface temperature distribution in the ceramic filter and electric heaters were measured with varying both the electrical power supply to the heaters and the mass flow rate of the air supply from a blower. The higher mass flow rate in the DPF system enhanced the uniformity in the surface temperature distribution of the ceramic filter due to effective convection heat transfer. The flow in the monolith ceramic structure of the DPF move mainly in the axial direction, which could be identified from the surface temperature of the ceramic filter.

• 한국대기환경학회지
• /
• 제28권2호
• /
• pp.203-210
• /
• 2012

The purpose of this study is to evaluate the diesel retrofit program which have been proceeded for the last 7 years in Gyeonggi-do. Diesel retrofit programs in Gyeonggi-do consist of the attachment of DPF (Diesel Particulate Filter), p-DPF (partial-DPF) and DOC (Diesel Oxidation Catalyst), switching to LPG engine, scraping an old cars. Emission reduction by diesel retrofit program was estimated $N_2O$ 8,313.4 ton/year, PM10 3,626.4 ton/year, VOC 8,078.5 ton/year in 2010. The benefit-cost analysis shows that the 964 billion wons of benefits are greater than the 853 billion wons of total costs. Diesel retrofit programs could be one of the most effective measures to improve PM10 concentration in metropolitan area. But retrofit programs also need to be properly maintained by each vehicle.