• Journal of Korea Multimedia Society
• /
• v.8 no.4
• /
• pp.439-449
• /
• 2005

Distributed main memory database management systems (DMM-DBMSs) store the database in main memories of the participating sites. They provide high performance through fast access to the local databases and high speed communication among the sites. Recently, a lot of research results on DMM- DBMSs has been reported. However, to the best of our knowledge, there is no known research result on the performance of the catalog management schemes for DMM-DBMSs. In this work, we evaluated the performance of the partitioned catalog management schemes through experimental analysis. First, we classified the partitioned catalog management schemes into three categories : Partitioned Catalogs Without Caching (PCWC), Partitioned Catalogs With Incremental Caching (PCWIC), and Partitioned Catalogs With Full Caching (PCWFC). Experiments were conducted by varying the number of sites, the number of terminals per site, buffer size, write query ratio, and local query ratio. Experiments show that PCWFC outperforms the other two schemes in all cases. It also means that the performance of PCWIC gradually increases as time goes by. It should be noted that PCWFC does not guarantee high performance for disk-based distributed DBMSs in cases when the workload of individual site is high, catalog write ratio is high, or remote data objects are accessed very frequently. Main reason that PCWFC outperforms for DMM-DBMSs is that query compilation and remote catalog access can be done in a very high speed, even when the catalogs of the remote data objects are frequently updated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.118-118
• /
• 2013

DMM은 방사광가속기의 백색광으로부터 단색광을 추출하기 위해 두 개의 다층 박막 (multilayer) 거울을 사용하는데, 첫 번째 거울은 Bragg 반사를 통해 분광을 하여 단색광을 생산하는 용도이고, 두 번째 거울은 이 단색광을 반사시켜 지면과 평행하게 출사되게 하기 위함이다. 일반적으로 사용되는 DCM (Double Crystal Monochromator)과의 차이점은, Bragg 반사를 위해 DCM에서는 결정을 사용하는 반면 DMM은 밀도차이가 많이나는 두 종류의 물질을 교대로 쌓아 올린 다층 박막을 사용한다는 것이다. 다층 박막의 주기가 곧 Bragg 반사에서의 d-spacing이 되며, X-선 분광의 목적으로 사용되는 d-spacing은 10-50 $\AA$ 사이이다. DCM이 0.01% 대의 우수한 에너지 분해능을 보이는데 비해, DMM은 1% 정도이다. 이 때문에 출사광의 밝기가 DCM에 비해 100배 밝은 특징이 있어서 에너지 분해능보다 광량이 더 중요한 응용에서 DMM이 사용된다. X-선 영상이나 방사선치료가 바로 이러한 응용에 해당한다. DMM은 포항가속기연구소와 (주) 벡트론에서 공동 설계하였으며, (주)벡트론에서 제작하였다. 그림 1에 DMM의 외형과 내부 구조를 나타내었다. Bragg 각의 조절 범위는 0.24-0.9도 이다. 입사광과 출사광의 수직 방향 offset을 10 mm로 유지하기 위해 두 번째 다층 박막이 수평방향으로 1,000 mm 가량 이동할 수 있어야 한다. 이를 위해 두 대의 고니오미터 stage를 사용하여 각각 첫 번째 및 두 번째 다층 박막의 위치와 방향을 제어한다. 첫 번째 다층 박막을 제어하는 고니오미터 stage는 하부가 전체 프레임에 고정되어 있고, 이 고니오미터의 회전축에서 Bragg 각을 조절한다. 두 번째 다층 박막을 제어하는 고니오미터 stage는 높이방향과 수평방향으로 이동이 가능하다. 다층 박막의 pitch는 고니오미터의 회전축에서 조절한다. 그리고 tilt stage를 사용하여 다층 박막의 roll을 조절한다.

• The Journal of the Petrological Society of Korea
• /
• v.5 no.1
• /
• pp.89-107
• /
• 1996

Sr, Nd and Pb isotopic characteristics of alkaline lavas and tholeiites in Cheju Island show that the isotopic compositions of the former slightly overlap, but have relatively more depleted than the latter. However, in viewpoint of the two eruptional stratigraphies of tholeiites, the isotopic compositon of the older one is similar to those of alkaline rocks in Lava Plateau Stage after Lee (1982). These suggest that the parental magmas of alkaline lavas and tholeiites might have originated from the homogenous mantle sourve and that the characteristics of the mantle source to be partially melted might be different between the eruption stages. The isotopic signatures of the bolcanic rocks in Cheju Island overlap with those in Samoa Islands and South China Basin, indicating the DMM-EM IImixing trend. This is distingushed from the DMM-EM I trend of the Cenozoic volcanic rocks in Korea except for cheju Island and Northeastern China. The modelled binary mixing calculation between MM and EM IImaterials indicates that the mantle source of the volcanic rocks in Cheju Island has been mixed about less than 10% of enriched mantle material (EM II) with depleted mantle material (DMM). Concerned with the indentation model between North China Block (NCB) and South China Block (SCB) after Yin an Nie (1993), we suggest that the distinct isotopic features of DMM-EM I and DMM-EM IIof the Cenozoic volcanic rock in Korea as well as China can be explained by the difference of the nature of subcontinental lithospheric mantle as enriched mantle materials, i.e. EM I of NCB, while EM II of SCB.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.6
• /
• pp.628-637
• /
• 2004

The present study investigates the performance of dynamic mixed model (DMM; Zang et ai.) in a channel with strong wall injection through a Large eddy simulation (LES) technique. The DMM results are compared with those of DNS and the results obtained with popular dynamic Smagorinsky model (DSM). Better agreement is achieved when using the DMM with box filter than DSM and coarse DNS in predicting the first and second order statistics as well as large-scale structures of velocity and temperature fields. Such favorable features of DMM are attributed to the fact that it explicitly calculates the modified Leonard stress term and only models the remaining cross and the SGS Reynolds stress terms and, thus, it reduces the excessive burden put on the model coefficient of DSM. Also it is demonstrated that the DMM can be successfully extended to the prediction of temperature (passive scalar) field where strong streamwise inhomogeneity exists.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.2
• /
• pp.43-48
• /
• 2008

The exhaust emissions of diesel engine are recognized as a major cause influencing environment strongly. In this study, the possibility of biodiesel fuel and oxygenated fuel(dimethoxy methane; DMM) was investigated as an alternative fuel for a naturally aspirated direct injection diesel engine. The smoke emission of blending fuel(biodiesel fuel 90vol-%+DMM 10vol-%) was reduced approximately 70% at 2500rpm, full load, in comparison with the diesel fuel. But, power, torque and brake specific energy consumption showed no significant differences. But, NOx emission of biodiesel fuel and DMM blended fuel increased compared with commercial diesel fuel due to the oxygen component in the fuel. It was needed a NOx reduction counterplan that EGR method was used as a countermeasure for NOx reduction. It was found that simultaneous reduction of smoke and NOx emission was achieved with BDF(95 vol-%) and DMM(5 vol-%) blended fuel and cooled EGR method(15%).

• International Journal of Internet, Broadcasting and Communication
• /
• v.12 no.4
• /
• pp.33-41
• /
• 2020

Nowadays, distributed mobility management (DMM) approaches have been widely adopted to address the limitations of centralized architectural methods to support seamless data transmission schemes in wireless sensor networks. This paper deals with the end-to-end (E2E) integration of Network Mobility (NEMO) basic support protocol in distributed wireless sensor network systems in structural health and environmental monitoring of social overhead capital (SOC) public infrastructures such as bridges, national highways, tunnels, and railroads. The proposed scheme takes advantage of the features of both the NEMO basic support protocol and partially distributed network-based DMM framework in providing seamless data transmission and robust mobility support. The E2E seamless data transmission scheme allows mobile users to roam from fixed-point network access locations and mobile platforms (i.e., vehicles such as cars, buses, and trains) without disconnecting its current sessions (i.e., seamless handover).

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.104-107
• /
• 2002

Direct Metal Manufacturing (DMM) is a new additive process that aims to take die making and metalworking in an entirely new direction. It is the blending of five common technologies : lasers, computer-aided design (CAD), computer-aided manufacturing (CAM), sensors and powder metallurgy. The resulting process creates parts by focusing an industrial laser beam onto a tool-steel work piece or platform to create a molten pool of metal. A small stream of powdered tool-steel metal is then injected into the melt pool to increase the size of the molten pool. By moving the laser beam back and forth, under CNC control, and tracing out a pattern determined by a computerized CAD design, the solid metal part is built line-by-line, one layer at a time. DMM produces improved material properties in less time and at a lower cast than is possible with traditional fabrication.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.5
• /
• pp.66-72
• /
• 2004

In this study, the effects of oxygen component in fuel and exhaust gas recirculation(EGR) method on the exhaust emissions has been investigated for a D.I. diesel engine. It was tested to estimate change of exhaust emission characteristics for the commercial diesel fuel and oxygenate blended fuel which has five kinds of blending ratio. Dimethoxy methane(DMM) contains oxygen component 42.5% in itself, and it is a kind of effective oxygenated fuel for reduction of smoke emission. It was affirmed that smoke emission was decreased with increasing of DMM blending ratio. But, NOx emission was increased compared with commercial diesel fuel. It was needed a NOx reduction counterplan that EGR method was used as a countermeasure for NOx reduction. It was found that simultaneous reduction of smoke and NOx emission was achieved with DMM blended fuel and cooled EGR method(1015%).

• Korean Journal of Food Science and Technology
• /
• v.53 no.5
• /
• pp.634-639
• /
• 2021

This study investigated the effects of cold plasma (CP) treatment on the properties of biopolymer films prepared with defatted mustard meal (DMM films). CP treatments using N₂, O₂, He, Ar, and dry air did not affect the tensile properties, water vapor permeability, color, and morphology of DMM films, whereas the treatments using He and Ar improved their printability. The tensile strength (TS) of O₂- or air-CP-treated DMM films and the elastic modulus (EM) of O₂-, He-, Ar-, or air-CP-treated films were lower than those of the untreated films. An increase in the power of Ar-CP treatment resulted in an increase in EM. The optimum treatment power and time for minimizing yellowness changes by Ar-CP treatment were 420 W and 40 min, respectively. The results demonstrated the potential application of CP treatment to improve the film properties of DMM films and possibly other agricultural by-product-based biopolymer films, making the films more applicable to food packaging.

• Smart Media Journal
• /
• v.2 no.2
• /
• pp.28-32
• /
• 2013

In this paper, we present a method to reduce complexity of depth modeling modes (DMM) that are used in the current 3D-HEVC standardization. DMM adds four modes to the existing HEVC intra prediction modes for accurate object edge representation in the depth map. Especially, Mode 3 requires distortion calculation of numerous pre-defined wedgelets, inducing high complexity. The proposed method employs absolute differences of neighboring pixels in the sides of the reference block to find high intensity changing positions. Based on such positions, the number of wedgelet candidates is reduced to six and distortion calculation is skipped for irrelevant wedgelets. Experimental results show complexity reduction by 3.1% on average, while maintaining similar coding performance.