• Steel and Composite Structures
• /
• 제31권2호
• /
• pp.113-123
• /
• 2019

In this study, carbon fiber/epoxy (CF/EP) composites were interleaved with aramid nonwoven veils with an areal weight density of $8.5g/m^2$ to improve their Mode-I fracture toughness. The control and aramid interleaved CF/EP composite laminates were manufactured by VARTM in a [0]4 configuration. Tensile, three-point bending, compression, interlaminar shear, Charpy impact and Mode-I (DCB) fracture toughness values were determined to evaluate the effects of aramid nonwoven fabrics on the mechanical performance of the CF/EP composites. Thermomechanical behavior of the specimens was investigated by Dynamic Mechanical Analysis (DMA). The results showed that the propagation Mode-I fracture toughness values of CF/EP composites can be significantly improved (by about 72%) using aramid nonwoven fabrics. It was found that the main extrinsic toughening mechanism is aramid microfiber bridging acting behind the crack-tip. The incorporation of these nonwovens also increased interlaminar shear and Charpy impact strength by 10 and 16.5%, respectively. Moreover, it was revealed that the damping ability of the composites increased with the incorporation of aramid nonwoven fabrics in the interlaminar region of composites. On the other hand, they caused a reduction in in-plane mechanical properties due to the reduced carbon fiber volume fraction, increased thickness and void formation in the composites.

• Proceedings of the Korea Water Resources Association Conference
• /
• 한국수자원학회 2020년도 학술발표회
• /
• pp.115-115
• /
• 2020

Water network partitioning (WNP) is an initiative technique to divide the original water distribution network (WDN) into several sub-networks with only sparse connections between them called, District Metered Areas (DMAs). Operating and managing (O&M) WDN through DMAs is bringing many advantages, such as quantification and detection of water leakage, uniform pressure management, isolation from chemical contamination. The research of WNP recently has been highlighted by applying different methods for dividing a network into a specified number of DMAs. However, it is an open question on how to determine the optimal number of DMAs for a given network. In this study, we present a method to divide an original WDN into DMAs (called Clustering) based on community structure algorithm for auto-creation of suitable DMAs. To that aim, many hydraulic properties are taken into consideration to form the appropriate DMAs, in which each DMA is controlled as uniform as possible in terms of pressure, elevation, and water demand. In a second phase, called Sectorization, the flow meters and control valves are optimally placed to divide the DMAs, while minimizing the pressure reduction. To comprehensively evaluate the WNP performance and determine optimal number of DMAs for given WDN, we apply the framework of multiple-criteria decision analysis. The proposed method is demonstrated using a real-life benchmark network and obtained permissible results. The approach is a decision-support scheme for water utilities to make optimal decisions when designing the DMAs of their WDNs.

• Journal of the Institute of Electronics and Information Engineers
• /
• 제51권4호
• /
• pp.33-41
• /
• 2014

This paper presents an effective memory access method for a high-speed data transfer on mobile systems using a direct memory access controller that considers the characteristics of a multi-port memory controller. The direct memory access controller has an integrated channel management function to control multiple direct memory access channels. The channels are physically separated and operate independently from each other. Experimental results show that the proposed direct memory access method improves the transfer performance by up to 72% and 69% on read and write transfer cycles, respectively. The total number of transfer cycles of the proposed method is 63% less than in a commercial method under 4-channel access.

• Journal of Korean Society for Atmospheric Environment
• /
• 제15권4호
• /
• pp.403-415
• /
• 1999

To properly assess air pollution levels, application of quality assurance and quality control(QA/QC) is believed to be an essential step. In order to cope with such scientific principle, a field study was designed with an aim of comparing: 1) the methods of calibration for airborne pollutants and 2) the protocols developed for their measurements. Measurements were made at Han Yang University, Seoul during 29 May through 1 June 1998 under the management of the Division of Measurements and Analysis(DMA) of Korean Society for Atmospheric Environment(KOSAE). In this work, we report our results of intercomparative measurements on several gaseous criteria pollutants that were investigated mainly by the two institutes-Seoul National University(SNU) and the Korean Research Institute for Standards and Science(KRISS). Although measurements of major gaseous pollutants had been made routinely by many scientific institutes and organizations in Korea, most scientists involved in those studieswere obliged to do their experiments on the basis of their own procedural steps spaning from the preparation of gaseous standards to the methodological selections for the calibration. Hence, this campaign offered a unique opportunity to examine many important aspects on the measurements of these important gaseous pollutants. In the course of our study, we investigated the compatibility of data sets obtained by the two institutes in concert with reference data sets collected concurrently from a government-managed monitoring station. On the basis of our study, we conclude that different data sets made by different participants during this campaign agree well within the reasonable range of uncertainties.low, which indicated that during this period the potential acidity of precipitation was high but the neutralizing capacity was low. For Spring, pAi was very low but pH was slightly high. This was likely due to the large amount of $CaCO_3$ in the soil particles transported over a long range from the Chinese continent that were incorporated into the precipitation, and then neutralized the acidifying species with its high concentraton.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• 제28권9호
• /
• pp.1408-1414
• /
• 2004

The use of flip-chip technology has many advantages over other approaches for high-density electronic packaging. ACF (anisotropic conductive film) is one of the major flip-chip technologies, which has short chip-to-chip interconnection length, high productivity, and miniaturization of package. In this study, thermal fatigue lift of ACF bonding flip-chip package has been predicted. Elastic and thermal properties of ACF were measured by using DMA and TMA. Temperature dependent nonlinear hi-thermal analysis was conducted and the result was compared with Moire interferometer experiment. Calculated displacement field was well matched with experimental result. Thermal fatigue analysis was also conducted. The maximum shear strain occurs at the outmost located bump. Shear stress-strain curve was obtained to calculate fatigue life. Fatigue model for electronic adhesives was used to predict thermal fatigue life of ACF bonding flip-chip packaging. DOE (Design of Experiment) technique was used to find important design factors. The results show that PCB CTE (Coefficient of Thermal Expansion) and elastic modulus of ACF material are important material parameters. And as important design parameters, chip width, bump pitch and bump width were chose. 2$^{nd}$ DOE was conducted to obtain RSM equation far the choose 3 design parameter. The coefficient of determination ($R^2$) for the calculated RSM equation is 0.99934. Optimum design is conducted using the RSM equation. MMFD (Modified Method for feasible Direction) algorithm is used to optimum design. The optimum value for chip width, bump pitch and bump width were 7.87mm, 430$\mu$m, and 78$\mu$m, respectively. Approximately, 1400 cycles have been expected under optimum conditions. Reliability analysis was conducted to find out guideline for control range of design parameter. Sigma value was calculated with changing standard deviation of design variable. To acquire 6 sigma level thermal fatigue reliability, the Std. Deviation of design parameter should be controlled within 3% of average value.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• 제11권7호
• /
• pp.2708-2712
• /
• 2010

Amines, ammonia or 3-methoxypropylamine (MPA), are used to maintain the optimized pH for the prevention of corrosion in the secondary side of Pressurized Water Reactors (PWRs). They are differently dissociated as a function of temperature which is not same in each location of the water-steam cycle. pH at the operation temperature depends on temperature of fluid and equilibrium constants of water and amines. Thus, every amine provides the different pH in the entire secondary side so that pH is not only the sufficient parameter in corrosion control. The secondary parameter, i.e., buffer intensity, is the ability to maintain a stable pH when $H^+$ are added or removed due to the ingress of impurities or the reaction of corrosion. The buffer intensity is necessary to provide the selection criteria for the best pH control agent for secondary side and the basic understanding of the reason why the flow-accelerated corrosion(FAC) rate may demonstrate the bell-shape curve over temperature. The buffer intensities of ammonia and MPA were reviewed over the entire operation temperature of PWRs. The sufficient buffer intensity is provided for the inhibition of corrosion by ammonia in low temperature $(25{\sim}100^{\circ}C)$ and by DMA in high temperature $(150{\sim}250^{\circ}C)$. In terms of buffer intensity, i) the best pH control agent is an amine with $pK_a(T)$ range of pH(T)- $1{\leq}pK_a(T){\leq}pH(T)$ + 0.5 and ii) the amine solution should have sufficient buffer intensity, ${\beta}$ to inhibit corrosion, and iii) FAC rate may be maximum at the temperature, where ${\beta}_B/{\beta}$ ratio is lowest.

• Journal of KIISE:Computing Practices and Letters
• /
• 제14권4호
• /
• pp.369-377
• /
• 2008

Today, Ethernet technology is rapidly developing to have a bandwidth of 10Gbps beyond 1Gbps. In such high-speed networks, the existing method that host CPU processes TCP/IP in the operating system causes numerous overheads. As a result of the overheads, user applications cannot get the enough computing power from the host CPU. To solve this problem, the TCP/IP Offload Engine(TOE) technology was emerged. TOE is a specialized NIC which processes the TCP/IP instead of the host CPU. In this paper, we implemented a high-performance, lightweight TCP/IP(HL-TCP) for the TOE and applied it to an embedded system. The HL-TCP supports existing fundamental TCP/IP functions; flow control, congestion control, retransmission, delayed ACK, processing out-of-order packets. And it was implemented to utilize Ethernet MAC's hardware features such as TCP segmentation offload(TSO), checksum offload(CSO) and interrupt coalescing. Also we eliminated the copy overhead from the host memory to the NIC memory when sending data and we implemented an efficient DMA mechanism for the TCP retransmission. The TOE using the HL-TCP has the CPU utilization of less than 6% and the bandwidth of 453Mbps.

• Journal of Food Hygiene and Safety
• /
• 제17권2호
• /
• pp.94-100
• /
• 2002

This work was performed in order to examine the effect of nitrite, thiocyanate and ascorbic acid on formation of N-nitrosamine(NA) in kimchi, fermented anchovy and shrimp under simulated gastric digestion, in vitro. The contents of nitrate were 10.7~24.5 mg/kg in kimchi, 1.5~5.6 mg/kg in fermented anchovy, 1.0~2.0 mg/kg in fermented shrimp and those of nitrite were average 0.3 mg/kg in all analyzed samples. Dimethylamine and trirmethylarnine contents were 4.9~l5.4 mg/kg, 0.6~0.8 mg/kg in kimchi, 3.3~4.0 mg/kg, 1.9~2.8 mg/kg in fermented anchovy, 30.3~177.9 mg/kg, 4.4~21.3 mg/kg in fermented shrimp, respectively. The contents of N-nitrosodime -thylamine(NDMA) were in the range of 0.8~6.9 $\mu\textrm{g}$/kg in kimchi, 0~l.2 $\mu\textrm{g}$/kg in fermented anchovy and 0~0.9 $\mu\textrm{g}$/kg in fermented shrimp. After simulated gastric digestion, NDMA was increased about 1.5 times in all sample. In every nitrite added samples, the contents of NDMA were increased by 183.1 times in fermented shrimp and were detected 192.4 $\mu\textrm{g}$/kg and 220.9 $\mu\textrm{g}$/kg when it was treated with 4 mM and 8 mM of nitrite, respectively. NDMA, when above samples were added 8 mM nitrite and 6.4 mM thiocyanate, was increased about 1.5 times than control samples. The formation of NDMA was inhibited by 49.9~92.4% in all samples added 12.8 mM ascorbic acid compared with the control sample.

• Polymer(Korea)
• /
• 제32권2호
• /
• pp.163-168
• /
• 2008

Biomedical scaffold for tissue regeneration was fabricated by one of rapid prototyping processes, bioplotting system, with a biodegradable and biocompatible poly($\varepsilon$-carprolactone)(PCL). Through dynamic mechanical test, it was observed that the PCL scaffold manufactured by the bioplotting process has the superior mechanical properties compared to the conventional scaffold fabricated by a salt-leaching process, and the plotted scaffold could be employed as a potential scaffold to regenerating hard and soft tissue. The plotted scaffold was consisted of porous structures. which were interconnected with each pore to help cells be easily adhered and proliferated in the wall of pore tunnels, and metabolic nutrients can be transported within the matrix. By using the plotting system, we could adjust the pore size, porosity, strand pitch, and, strand diameter of PCL scaffolds, which were important parameters to control mechanical properties of the scaffolds, and consequently we could determine that the mechanically controlled scaffolds could be used as a matching scaffold for any required mechanical properties of the target organ. The fabricated 3D PCL scaffold showed enough possibility as a 3D biomedical scaffold, which was cell-cultured with chondrocytes.

• Journal of the Institute of Convergence Signal Processing
• /
• 제15권2호
• /
• pp.70-75
• /
• 2014

Recently, the demand for high-integrated, low-powered, and high-powered SoC design has been increasing due to the multi-functionality and the miniaturization of digital devices and the high capacity of service informations. With the rapid evolution of the system, the required hardware performances have become diversified, the FPGA system has been increasingly adopted for the rapid verification, and SoC system using the FPGA and the ARM core for control has been growingly chosen. While the AXI bus is used in these kinds of systems in various ways, it is traditionally designed with AXI slave structure. In slave structure, there are problems with the CPU resources because CPU is continually involved in the data transfer and can't be used in other jobs, and with the decreased transmission efficiency because the time not used of AXI bus beomes longer. In this paper, an efficient AXI master interface is proposed to solve this problem. The simulation results show that the proposed system achieves reductions in the consumption clock by an average of 51.99% and in the slice by 31% and that the maximum operating frequency is increased to 107.84MHz by about 140%.