• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술회의 논문집 정보 및 제어부문 A
• /
• pp.271-274
• /
• 2003

This paper presents a Built-in Current Sensor that detect defects in CMOS integrated circuits using the current testing technique. This scheme employs a cross-coupled connected PMOS transistors, it is used as a current comparator. Our proposed scheme is a negligible impart on the performance of the circuit undo. test (CUT). In addition, in the normal mode of the CUT not dissipation extra power, high speed detection time and applicable deep submicron process. The validity and effectiveness are verified through the HSPICE simulation on circuits with defects. The entire area of the test chip is $116{\times}65{\mu}m^2$. The BICS occupies only $41{\times}17{\mu}m^2$ of area in the test chip. The area overhead of a BICS versus the entire chip is about 9.2%. The chip was fabricated with Hynix $0.35{\mu}m$ 2-poly 4-metal N-well CMOS technology.

• 소성∙가공
• /
• 제9권1호
• /
• pp.27-34
• /
• 2000

Sheet metal formabilities for aluminum 1050 and 5052 were experimentally investigated in this study. Deep drawability, bendability and stretch formability were measured at each process condition and correlated with tensile properties of sheet metal. To compare the formabilities of aluminum 1050 and 5052 sheets with those of steel sheets, deep drawing quality(DDQ) steel sheets are also tested at the same test conditions. Through the experimental studies, influential process variables for each forming process were obtained and correlated with the tensile properties. The comparisons of sheet metal formabilities with those of steed sheets showed that aluminum 1050 and 5052 is inherently deficient in formability than steel sheets but Al 5052 that has highter n and r value than al 1050 showed better formabilities.

• Bulletin of the Korean Chemical Society
• /
• 제19권3호
• /
• pp.314-319
• /
• 1998

One flask synthesis of dithienylmethane and difurylmethane is reported. The reaction of aldehydes with excess furan or thiophene affords the meso-phenyldithienylmethane (DTM) and meso-phenyldifurylmethane (DFM), respectively. The reaction is catalyzed with trifluoroacetic acid or with BF3·O(Et)2. An acyl group is selectively introduced in 1 and 9 position of difurylmethane and dithienylmethane by use of an acid chloride and tin (IV) chloride. The reduction of resulting 1,9-bisacyldifurylmethane or 1,9-bisacyldithienylmethane affords the corresponding 1,9-bis-diol. An acid catalyzed condensation of diol with meso-phenyldipyrromethane followed by oxidation with DDQ gives the porphyrins. The reaction resulted meso-5,10,15,20-tetraphenyl-21,22-dithiaporphyrin (SSNN) or 15-mesityl-5,10,20-triphenyl-21,22-dioxaporphyrin (OONN), respectively. The formation of small amount of meso-tetraphenylporphyrin (TPPH2) is also observed. The formation of TPP indicates that meso-phenyldipyrromethane is reversibly cleaved and form pyrrole and pyrrylbenzylcarbocation during the condensation. The proton nmr and electronic spectrum of the SSNN and OONN porphyrins are somewhat different from the previously synthesized meso-5,10,15,20-tetraphenyl-21,23-dithiaporphyrin (SNSN) or meso-5,10,15,20-tetraphenyl-21,23-dioxaporphyrin (ONON).

• 한국기계가공학회지
• /
• 제13권3호
• /
• pp.63-69
• /
• 2014

This paper studies the strength, fatigue sensitivity, safety factor and lifetimes by means of structural and fatigue analyses of different models of rear doors upon the opening of doors and windows leading to severe fatigue fractures of the window motor components of rear doors. The simulation models were a standard model and other models. The other models, which are denoted here as models I and II, were modified versions of the standard model, with a rib of 3mm and a thickness of 2mm as compared to the standard model. The door was modelled with CATIA V5 and analyzed with the ANSYS program. The material of the rear door was cold rolled steel (DDQ). From the study results, the standard model and model I were confirmed to be less safe upon the opening of the door as compared to the opening of a window in terms of fatigue, but model II was found to be safe for both door and window openings.

• 약학회지
• /
• 제51권1호
• /
• pp.56-62
• /
• 2007

Twelve epoxy and hydroxydiosgenin derivatives (DI-1${\sim}$DI-12) were synthesized from diosgenin (25(R)-5-spirosten-3${\beta}$-ol). Diosgenin was epoxidized with m-chloroperoxybenzoic acid (mCPBA) to oxidize 25(R)-4${\alpha}$,5${\alpha}$-epoxyspirostane (DI-1). Diosgenin was reacted with DDQ to form 25(R)-1,4,6-spirostatrien-3-one (DI-2), which was treated with 30% H$_2$O$_2$ to give 25(R)-1${\alpha}$,2${\alpha}$-epoxy-4,6-spirostadien-3-one (DI-3) and treated with mCPBA to form 25(R)-6${\alpha}$,7${\alpha}$-epoxy-1,4-spirostadien-3-one (DI-7), respectively. DI-3 was reduced with NaBH$_4$ to afford 25(R) -1${\alpha}$,2 ${\alpha}$-epoxy-4,6-spirostadien-3${\beta}$-ol(DI-4) and reacted with Li metal in absolute ethanol to form 25(R)-2-ethoxy-1,4,6-spirostatrien-3-one (DI-5). DI-7 was reduced with NaBH$_4$ to produce 25(R)-3${\beta}$,7${\alpha}$-dihydroxy-4-spirostene (DI-8) and treated with Li metal in liquid ammonia to produce 25(R)-7${\alpha}$-hydroxy-4-spirosten-3-one (DI-9). DI-2 was reduced with NaBH$_4$ to form 25(R) -4,6-spirestadien-3${\beta}$-ol(DI-10), which was stirred with 30% H$_2$O$_2$ to synthesize 25(R)-4,6-spirostadien-3-one (DI-11) and reacted with mCPBA to give 25(R)-4${\beta}$,5${\beta}$ -epoxy-6-spirosten-3${\beta}$-ol (DI-12), respectively. The antinociceptive effects of synthesiz ed compounds were measured by hot plate method and compound DI-7 signifcantly exhibited antinociceptive effect. DI-2 decreased the serum triglyceride and total cholesterol levels in poloxamer P-407 injected rat.