• Journal of Advanced Marine Engineering and Technology
• /
• v.23 no.3
• /
• pp.292-299
• /
• 1999

DC motors are widely used in many industrial fields as the actuator of the robot and the driving power motors of the electrical vehicle, Usually in the sensors of DC motors such as the encoder the tachogenerator and the potentiometer etc. are applied, But usage of these sensors results in the increased price and operating cost such that the application of the motors are limitted. To solve this problem another method to construct low cost control system is investigates. In this paper a new speed control method for DC motor is proposed. This method uses motor parameters instead of using speed or position sensors. In this way the angular velocity is estimated by the measure-ment values of the armature voltage and current instead of measuring the sensor signal. This paper presents an alorithm for estimating the angular velocity of DC motor The effectiveness of the proposed method is verified by experimental results. Also the applicability of the proposed method is presented by applying to the velocity contol of a wheeled mobile robot.

• Journal of Power Electronics
• /
• v.19 no.1
• /
• pp.11-23
• /
• 2019

In this study, a novel zero voltage zero current transition (ZVZCT) bidirectional DC-DC converter is proposed by employing coupled inductors. This converter can turn the main switch on at ZVZCT and it can turn it off with zero voltage switching (ZVS) for both the boost and buck modes. These characteristics are obtained by using a simple auxiliary sub-circuit regardless of the power flow direction. In the boost mode, the auxiliary switch achieves zero current switching (ZCS) turn-on and ZVS turn off. Due to the coupling inductors, this converter can make further efficiency improvements because the resonant energy in the capacitor or inductor can be transferred to the load. The main diode operates with ZVT turn-on and ZCS turn-off in the boost mode. For the buck mode, there is a releasing circuit to conduct the currents generated by the magnetic flux leakage to the output. The auxiliary switch turns on with ZCS and it turns off with ZVT. The main diode also turns on with ZVT and turns off with ZCS. The design method and operation principles of the converter are discussed. A 500 W experimental prototype has been built and verified by experimental results.

• Korean Journal of Medicinal Crop Science
• /
• v.11 no.4
• /
• pp.316-320
• /
• 2003

A protocol is described for rapid multiplication of Zanthoxylum piperitum DC. (Rutaceae), an important aromatic and medicinal plant, through shoot-tip explant cultures. Murashige and Skoog (MS) medium supplemented with various concentrations of N-6-benzyladenine (BA), N-6-benzylaminopurine (BAP) and thidiazuron (TDZ), in single or in combination with ${\alpha}-naphthaleneacetic$ acid (NAA), was used to determine the rate of shoot proliferation. N-6-benzyladenine (BA) used at 0.5mg/l, was the most effective in initiating multiple shoot proliferation at the rate of 23 microshoots per shoot-tip explants after 40 days of culture. Shoot multiplication increased 1.2-fold in each successive subculture. Induction of rooting (98%) was achieved by transferring the shoots to the same basal medium containing 2 mg/l indole-3-butyric acid (IBA). Plantlets went through a hardening phase in a controlled growth chamber, prior to in vivo transfer. These results represented that possible application for the mass production of plantlets through in vitro culture system of Zanthoxylum piperitum DC.

• Journal of the Semiconductor & Display Technology
• /
• v.23 no.1
• /
• pp.48-51
• /
• 2024

Recently, high-performance BLDC(Brushless DC) motors are being applied to various fields such as industrial and personal mobility devices and drones. To achieve the best performance of BLDC, sensors such as hall sensors, encoders, and resolvers are used to determine the position of the rotor, and various speed control technologies are being developed. However, due to problems with high-speed control due to external environmental factors and frequency bandwidth of semiconductor sensing devices, research on BLDC motors without semiconductor sensing devices is in progress. Therefore, in this study, a signal brush was added to the end of the rotor of a BLDC motor and the rotor position of the BLDC motor was detected by analyzing the signal output through the signal brush.

• Journal of Korea Society of Industrial Information Systems
• /
• v.23 no.1
• /
• pp.31-41
• /
• 2018

This paper discusses a structure design and thermal analysis of cryogenic conduction cooling system for a high current HTS DC reactor. Dimensions of the conduction cooling system parts including HTS magnets, bobbin structures, current leads, support bars, and thermal exchangers were calculated and drawn using a 3D CAD program. A finite element method model was built for determining the optimal design parameters and analyzing the thermo-mechanical characteristics. The operating current and inductance of the reactor magnet were 1,500 A, 400 mH, respectively. The thermal load of the HTS DC reactor was analyzed for determining the cooling capacity of the cryo-cooler. Hence, we carried out the operating test of conduction cooling system of the 1st stage area with high current flow. The cooper bars was cooled down to 40 K and HTS leads operated stably. As a experiment result, the total heat load of the 1st stage area is 190 W. The study results can be effectively utilized for the design and fabrication of a commercial HTS DC reactor.

• Korean Journal of Food Science and Technology
• /
• v.21 no.4
• /
• pp.562-568
• /
• 1989

The essential oils from ripe fruit peel and leaf of Zanthoxylum piperitum DC were extracted by gas co-distillation method and analyzed by gas chromatography/mass spectrometry (GC/ MS) and retention index matching. The experimental results revealed the presence of over 100 volatile components. Major components were 1,8-cineol (25.47%), limonene (11.91%), geranyl acetate (9.01%), myrcene (6.15%) in fruit peel and citronellal (23.11%), 1,8-cineol (18.38%), citronellol (6.04%) in leaf. Among the components identified were the following; in fruit peel, ${\alpha}-pinene$ and 13 hydrocarbons, linalool and 8 alcohols, citronellal and 3 aldehydes, carvone and 2 kotones, methyl salicylate and 7 esters, and 1,8-cineol and oxides, and in leaf, ${\alpha}-pinene$ and 7 hydrocarbons, linalool and 7 alcohols, citronellyl acetate and 5 esters, citronellal and 1 aldehyde, carvone, and 1,8-cineol and 1 oxide.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.23-30
• /
• 2011

This paper presents a Single-Inductor Multiple-Output (SIMO) DC-DC Converter with a negative feedback selection circuit to improve a regulation property at light load and to generate independent multiple outputs. The conventional SIMO DC-DC converter with a fixed negative feedback circuit cannot regulate correctly at light load. The SIMO DC-DC converter with the proposed negative feedback selection circuit has been designed in 0.35um 2-poly 3-metal BCDMOS. This converter is dual output boost converter with the 1.5V input and 2.5V, 3.0V output. The power conversion efficiency varies from 59% at 10mA loads to 85% at 50mA loads.

• The Journal of Engineering Geology
• /
• v.9 no.1
• /
• pp.45-57
• /
• 1999

Groundwater flow in rock mass is controlled by the fractures developed in the area. So, the conductive fractures are very important for groundwater flow in crystalline rock. This study aims to find out the characteristics of the fracture distributed in granitic rock in the northern part of the Yusong area (latitude $36^{\circ}24'18"~36^{\circ}25'08",{\;}longitude{\;}127^{\circ}21'00"~127^{\circ}23'23"$). The electric and EM surveys were carried out in the site to delineate the fracture the fracture zones. Since geophysical survey provides non-unique solution, hydraulic data and dilling log data including BHTV scanning were used as complementary data to achieve the objective of this study. Electric survey(DC) arrays used are schlumberger and dipole-dipole arrays. VLF is used for EM survey. The main charcteristics of the fracture developed in the study aera are that fractures associated with basic dyke cut corss the main fracture zone in NNW and play an important role as hydraulic barrier. In trun, groundwater table in the upstream area is lower than that downstream area.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.1
• /
• pp.52-60
• /
• 1997

A 23GHz 2-stage LNA was designed using MPIE numerical analysis and microwave CAD EEsof softwares. The basic circuit was designed by EEsof tools but analyzed more precisely using numerical MPIE tools and modified. The matching sections of the input and output terminals were designed with paralledl coupled filter-type lines, these matching sections perform impedance matching and DC blocking, more over have the advantages of small discontinuities and small errors in the design process. The FET chip is directly attached to the ground metal. The designed LNA gives 15.2dB gain and 2.7dB noise figure. without considering 1.8dB loss of connectors. These results validate our design process and matching schemes and fabrication technologies over the 20GHz frequency range.

• 전자공학회논문지 IE
• /
• v.49 no.1
• /
• pp.18-23
• /
• 2012

In this paper, a potable device application for DC-DC converter was designed for voltage protection circuit. Voltage protection circuit to offer the under voltage lock out and over voltage protection consists of a comparator and bais circuits were implemented using. XFAB 1um CMOS process, SPICE simulations was confirmed through the characteristics. Simulation results, under voltage lock out input voltage is 4.8 V higher when the turn-on and, 4.2 V less when turn-off. When the input voltage is low voltage is applied can be used to prevent malfunction of the circuit. Over voltage protection is 3.8 V reference voltage when the output voltage caused by blocking circuit prevents device destruction can be used to improve the stability and reliability. The virtual control circuits of the DC-DC converter connected. According to the results of the abnormal voltage, voltage protection circuit behavior was confirmed. The proposed voltage protection circuit of the DC-DC converter cell is useful are considered.