• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.3
• /
• pp.491-498
• /
• 2020

Recently, In the production line of batteries, charge and discharge tests are essential to verify battery characteristics. In this case, the battery charging uses a unidirectional AC/DC converter capable of output voltage and current control, and the discharge uses a resistive load. Since this method consumes energy during discharge, it must be replaced with a bi-directional AC/DC converter system capable of charging and discharging. Although it is difficult to replace the connected inverter part of the bi-directional AC/DC converter system due to the high cost, the spread of the solar-connected inverter rapidly increases as the current solar supply business is activated, and thereby the solar-connected type Inverter prices are plunging. If it can be used as a power converter for battery discharge without program modification of the solar-powered inverter, it will have competition. In this paper, propose a new battery discharge system using a combination of a photovoltaic DC/DC simulator and photovoltaic PCS using a battery to be used as a power converter for battery discharge without program modification of a low-cost photovoltaic inverter. In addition, propose an optimal solar characteristic curve for the stable operation of PCS. The validity of the proposed system was verified using a 500[W] class solar DC/DC simulator and a solar PCS prototype.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.5
• /
• pp.328-335
• /
• 2018

An energy management method of DC microgrids using voltage compensation term is proposed in this study. Droop control is often implemented to operate the DC microgrid. However, the droop control necessarily generates voltage variation. Energy flow is also difficult to control because the droop control mainly focuses on proportional load sharing. To solve these problems, the voltage compensation term based on the low-bandwidth communication is used to determine the operating band of the converter. Energy management and voltage variation minimization can be achieved by judging the operating band according to the magnitude of voltage compensation term. The validity of the proposed method is verified by simulation and experiments.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.5
• /
• pp.345-351
• /
• 2018

A distributed control method is proposed to improve the power sharing performance of bidirectional distributed generators and the voltage regulation performance of a DC bus in a DC microgrid. Voltage sensitivity analysis based on power flow analysis is conducted to analyze the structural characteristics of a DC microgrid. A distributed control method using a voltage sensitivity matrix is proposed on the basis of this analysis. The proposed method uses information received through the communication system and performs the droop gain variation method and voltage shift method without additional PI controllers. This approach achieves improved power sharing and voltage regulation performance without output transient states. The proposed method is implemented through a laboratory-scaled experimental system consisting of two bidirectional distributed generators, namely, a load and a non-dispatchable distributed generator in a four-bus ring-type model. The experimental results show improved power sharing accuracy and voltage regulation performance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.5
• /
• pp.305-312
• /
• 2018

DC distribution systems has recently taken the spotlight. Concerns over human safety and stability facility are raised in DC distribution systems. Std. IEC 60479 provides basic guidance on "the effects of shock current on human beings and livestock" for use in the establishment of electrical safety requirements and suggests an electrical impedance of the human body. This study analyzes impedance spectrums based on the electrical equivalent impedance circuit for the human body; human body impedances measured by experiments are analyzed below the fundamental frequency (60 Hz). The analysis shows that the equivalent impedance circuit for the human body should be modified at least in low-frequency range below the fundamental frequency (60 Hz). The DC residual current detection method that can classify electric shock accidents of humans and electric leakages of facilities is proposed by applying the analysis result. The detection method is verified by experiments on livestock.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.2_1
• /
• pp.139-147
• /
• 2020

In order to satisfy the voltage levels of the low voltage battery side and high voltage DC bus, a high voltage gain with bidirectional operation is required. In this system, the cost effectiveness of the design is a critical factor; therefore, the system should be designed using a small number of components. This paper propose a novel bidirectional converter composed with a quasi-sepic and switched-indictor network. The proposed converter consists a small number of components with a high voltage gain ratio. Detailed analysis are made with respect to the operating mode, number of components, voltage and current ripple and efficiency. To verify performance of the proposed converter, simulation was performed is this paper. The simulation results are shown to verify the feasibility and performance of the proposed bidirectional converter.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.9-13
• /
• 2019

This paper presents an optimal design of a brushless DC motor considering an advanced $165^{\circ}$ 12 step control for a cost reduction. The advanced 12 step control that extends the conduction angle $150^{\circ}$ can improve the output of the motor. The optimal design considering the improved output power of the motor is proposed by reducing the volume of rotor, stator and permanent magnet using response surface method. The proposed design satisfied the performance requirements and efficiency improvement of the conventional motor and reduced the volume about 3.5%. The feasibility of the optimal design is proved by the electromagnetic field analysis using the finite element method.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.310-313
• /
• 2019

This paper used the majority function to digitally filter back-electromotive force as an explanation of the Brushless DC MOTOR control algorithm. The cause and improvement of motor noise, which are operating in close proximity to high frequency sources, did not use conventional low pass filter and comparator elements. Also, they repeatedly output a noise-free BEMF signal for the input value of the majority detection filtering. These filtering steps can help reduce costs and minimize the area of a PCB by requiring relatively little hardware.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.5
• /
• pp.640-645
• /
• 2012

DC-DC converter and DC-AC inverter in a hybrid electric vehicle (HEV) generate the switching noise. It may be generated by the reverse recovery operation of the power diode in the switching circuit of the converter or the inverter. The shape of the reverse recovery region may be determined by both reverse time and recovery time in the diode. So, in this paper, the frequency spectrum of switching noise was estimated by the shape of the reverse recovery region and compared with the measured results. It shows that the meaningful region of the frequency spectrum is directly related with the reverse time.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.254-260
• /
• 2019

The failure rate of bidirectional dc-to-dc converter is predicted through the failure mode and effect analysis (FMEA) and the fault-tree analysis (FTA) considering the operational risk. In order to increase the driving voltage of the electric vehicle efficiently, the bidirectional converter is attached to the front of the inverter. It has a boost mode for discharging battery power to the dc-link capacitor and a buck mode for charging the regenerative power to the battery. Based on the results of the FMEA considering the operating characteristics of the bidirectional converter, the fault-tree is designed considering the risk of the converter. After setting the design parameters for the MCU for the electric vehicle, we analyze the failure rate of the capacitor due to the output voltage ripple and the inductor component failure rate due to the inductor current ripple. In addition, we obtain the failure rate of major parts according to operating temperature using MIL-HDBK-217F. Finally, the failure rate and the mean time between failures (MTBF) of the converter are predicted by reflecting the part failure rate to the basic event of the fault-tree.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.5
• /
• pp.1372-1383
• /
• 1998

In this paper, modeling for DC and AC characteristics analysis of DFB-LD was performed considering effects of .lambda./4-shifted gratingandspatial hole burning within a laser diode cavity. From the simulation for DC characteristics, Light-Current curve, optical power distribution and carrier density distribution within the cavity can be obtained. The simulation for AC characteristics porovides IM response and the amplitude and phase and the amplitude and phase response of FM with excellent accuracy.