• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.1
• /
• pp.57-62
• /
• 2008

From the progressing results, it was found that thin film using 52 wt% Ni - 38 wt% Cr - 3 wt% Al - 4 wt% Mn - 3 wt% Si target has good characteristics for low TCR (temperature coefficients of resistance) and high resistivity. The optimum sputtering condition was DC 250 W, 5 mtorr, and 50 sccm and the proper annealing condition was $350^{\circ}C$/3.5 hr in air atmosphere. At these fabricated conditions, thin film resistors with TCR values of less than ${\pm}10ppm/^{\circ}C$ were obtained. The TCR of the packaged-samples made at proper fabrication conditions was $-3{\sim}15ppm/^{\circ}C$ after the thermal cycling and $-20{\sim}180ppm/^{\circ}C$ after PCT (pressure cooker test), we could confirm reliability for the thin film resistor and find the need for enduring research about packaging method.

• Journal of Korea Multimedia Society
• /
• v.21 no.1
• /
• pp.61-68
• /
• 2018

In this paper, we present an effective encryption algorithm for 3D printing models in the frequency domain of discrete cosine transform to prevent illegal copying, access in the secured storage and transmission. Facet data of 3D printing model is extracted to construct a three by three matrix that is then transformed to the frequency domain of discrete cosine transform. The proposed algorithm is based on encrypting the DC coefficients of matrixes of facets in the frequency domain of discrete cosine transform in order to generate the encrypted 3D printing model. Experimental results verified that the proposed algorithm is very effective for 3D printing models. The entire 3D printing model is altered after the encryption process. The proposed algorithm is provide a better method and more security than previous methods.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.4
• /
• pp.289-295
• /
• 2008

In this paper, we designed the off-line PWM(Pulse width modulation) control IC for flyback type power converter to reduce the standby power consumption. In normal state, this off-line PWM IC generates the output pulse with $40\sim60kHz$ frequency and duty ratio of $20\sim88%$. When SMPS operates in standby mode, this IC generates the output pulse with 33kHz frequency and duty ratio of 1 %. SPICE simulation was performed to verify the standby power consumption of the power converter with designed of-line PWM IC. Power converter with designed off-line PWM IC consumes less than 0.3W when it operates in standby mode condition.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.6
• /
• pp.525-529
• /
• 2016

In the case of a motor system that converts electrical energy into mechanical energy, the region of the motor and that of the generator coexists. In the case of an escalator, the ascending escalator is operated by the motor, whereas the descending escalator is operated by the generator according to the load. To evaluate the proposed method, this study reduces the power of the ascending escalator up to approximately 35% by sharing the regeneration power of the descending escalator. The loss of transfer power nearly exists in the case of the proposed method. Furthermore, the lifetime of the DC link condenser can be extended because it is connected in parallel, thus leading to a twofold increase in capacity.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.2
• /
• pp.144-149
• /
• 2016

This paper presents a power control method of high-speed single-phase BLDC motor. Most electric appliances require a power factor corrector (PFC) to mitigate grid current harmonics. However, the reactive components and power semiconductors in the PFC increase system cost and dimension. In this paper, a new motor drive system for a high-speed single-phase BLDC motor is proposed, which can decrease grid current harmonics without PFC by directly manipulating motor power and eliminating bulky electrolytic dc-link capacitor. Given that the proposed motor power control method does not require motor current controller, no current sensor is necessary. Moreover, the proposed algorithms can be easily implemented using a low-cost micro-controller. The effectiveness of the proposed power control method is verified by experiments.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.2
• /
• pp.114-121
• /
• 2013

High efficiency operation is required for motors of vehicle to increase fuel efficiency due to the regulation of exhaust gas. This paper presents a control method of fuel pressure to increase fuel efficiency and a sensorless control method of BLDC motor to get higher efficiency than conventional brushed DC motor. Initial rotor position of BLDC motor is detected from current value that is occurred by test voltage pulse and rotor is accelerated by defined sequence to enter sensorless operation mode. The algorithm to control flow rate of fuel pump uses PI controller that is control motor speed to maintain the target fuel pressure commanded by ECU.

• Bulletin of the Korean Chemical Society
• /
• v.17 no.5
• /
• pp.447-452
• /
• 1996

Three conformational isomers of calix[4]arene butanoate were isolated from the reaction of calix[4]arene and butanoyl chloride in the presence of NaH and their structures were determined by NMR spectra as 1,2-alternate 2a, partial cone 2b and 1,3-alternate conformer 2c, respectively. The crystal structure of 2a has been determined by X-ray diffraction method. The crystals are monoclinic, space group C2/c, a=18.435 (4), b=13.774 (2), c=16.941 (3) Å, β=116.23 (1)°, Z=4, V=3858.8 (12)Å3, Dc=1.21 g cm-3, Dm=1.21 g cm-3. The molecule is in the 1,2-alternate conformation. It has two-fold symmetry axis along the line connecting between C (7AA') and C (7BB') parallel to the b axis of crystal lattice.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.4
• /
• pp.335-342
• /
• 2016

This paper proposes an energy storage-assisted, series-connected module-integrated power conversion system that integrates a photovoltaic power conditioner and a charge balancing circuit. In conventional methods, a photovoltaic power conditioner and a cell-balancing circuit are needed for photovoltaic systems with energy storage devices, but they cause a complex configuration and high cost. Moreover, an imbalanced output voltage of the module-integrated converter for PV panels can be a result of partial shading. Partial shading can lead to the fault condition of the boost converter in shaded modules and high voltage stresses on the devices in other modules. To overcome these problems, a bidirectional buck-boost converter with an integrated magnetic device operating for a charge-balancing circuit is proposed. The proposed circuit has multiple secondary rectifiers with inductors sharing a single magnetic core, which works as an inductor for the main bidirectional charger/discharger of the energy storage. The secondary rectifiers operate as a cell-balancing circuit for both energy storage and the series-connected multiple outputs of the module-integrated converter. The operating principle of the cell-balancing power conversion circuit and the power stage design are presented and validated by PSIM simulation for analysis. A hardware prototype with equivalent photovoltaic modules is implemented for verification. The results verify that the modularized photovoltaic power conversion system in the output series with an energy storage successfully works with the proposed low-cost bidirectional buck-boost converter comprising a single magnetic device.

• Journal of the Korea Convergence Society
• /
• v.9 no.4
• /
• pp.143-150
• /
• 2018

This work conducted the experimental analysis on ultrasonic acoustic matching in order to measure the accuracy of gaseous fuel level values. The experimental devices were used as 12V-DC supply, control T1 board, oscilloscope (DS01072B), ultrasonic probe and pattern table. The research models were designed by ceramic assay which can determine the transmitting and receiving energies. The result of the ringing area could verify the increased characteristics in the order of D (0.180m) < E (0.184m) < B (0.204m) < A (0.234m) < F (0.244m) < C (0.247m) models based on initial 2.9V of the maximum peak voltage. From the experimental results, the model designed by Ø21*3+2t of the matching layer was notable in that the most outstanding directivity energy could be created.

• Journal of Broadcast Engineering
• /
• v.21 no.3
• /
• pp.319-329
• /
• 2016

Internet Video Coding (IVC) is a royalty-free codec currently being developed in MPEG. Coding efficiency of IVC codec has been steadily enhanced and it was reported that the performance of Committee Draft (CD) version is comparable to H.264/AVC High Profile (HP) in terms of objective and subjective qualities. In this paper, we present some coding tools that have been proposed for enhancing the coding efficiency of IVC during the developing process in MPEG along with brief overview of IVC codec architecture and coding algorithms. The coding tools include both of normative tools and informative tools such as non-reference P frame coding, DC mode intra prediction, Lagrange multiplier selection, and extension of chroma intra prediction modes. Improvement obtained by each tool is presented in terms of algorithm and coding gain based on the experiments. As a result of the experiment, the coding tools give the average bit saving of 8.8%, 0.4%, 0.4%, and 0.0%, respectively, in the low-delay coding mode.