• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.2
• /
• pp.39-46
• /
• 2012

The newly designed sense amplifier in this paper has rail-to-rail input range achieving low power consumption. Reducing static power consumption generated due to DC path to ground is key element for low power consumption in this paper. The proposed sense amplifier performs power-saving operation using negative feedback circuit that controls the current flow with the newly added PMOS input terminal. As a simulation result, the proposed sense amplifier consumed about over 50 % efficiency of the average power consumed by the typical Rail-to-Rail sense amplifier.

• Journal of the Korean Society of Radiology
• /
• v.11 no.3
• /
• pp.101-108
• /
• 2017

DC/DC switching power converters are commonly used to generate a regulated DC output voltage with high efficiency. The advanced DC/DC converter uses a PWM-IC with OP-Amp. (Operational Amplifier) to control a MOSFET (metal-oxide semiconductor field effect transistor), which is a switching component, efficiently. In this paper, it is shown that the electrical characteristics of OP-Amp. are affected by radiations of ${\gamma}$ rays using $^{60}Co$ for TID (Total Ionizing Dose) testing and 5 heavy ions for SEL (Single Event Latch-up) testing. TID testing on OP-Amp. is accomplished up to the total dose of 30 krad, and the cross section($cm^2$) versus LET($MeV/mg/cm^2$) in the OP-Amp. operation is evaluated SEL testing after implementation of the controller board.

• Journal of the Korea Convergence Society
• /
• v.7 no.3
• /
• pp.77-85
• /
• 2016

We propose a digital signal processing technic that can compensate the non-linearity inherent in audio amplifiers, and present the result of the simulation. The inherent non-linearity of the audio power amplifier arising from analog devices is compensated via a digital signal processing technic consisting of indirect learning architecture and an adaptive filter. The simulation results show that the compensator can be realized using a third-order polynomial and compensates odd-order non-linearity efficiently. The even-oder non-linearity is mainly due to the dc offset at the output, which is difficult to eliminate with the proposed method. Care must be taken in designing the bias circuit to avoid the DC offset at the output. The proposed technic has significance in that digital signal processing technic can compensate for the impairment that is an inherent characteristic of an analog system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.10 s.113
• /
• pp.929-934
• /
• 2006

In the paper, we suggest a simpler synthesis technique for capacitively-coupled match circuit(CCMC) which have a function of DC block and impedance matching simultaneously, and introduce a stability margin analysis technique for designing microwave amplifier under conditionally stable state. Stability margin analysis is used to determine optimum match point that ensure maximum gain under the given stability margin. It can reduce time consuming work for selecting match points in the conditionally stable state. Also, suggested miniaturization scheme of matching network is distinguished from previous work with respect to reducing deterministic parameters for CCMC synthesis. To verify utility of suggested method, 24 GHz gain block is fabricated under conditionally stable state using an internal thin-film fabrication process, Measured results show a stable gain of 10 dB and flatness of 1 dB, which is well coincident with simulated one.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.900-905
• /
• 2009

A common drain feedback CMOS wideband LNA with current bleeding and input inductive series-peaking techniques is presented in this paper. DC coupling is adopted between cascode and feedback amplifiers, so that the gain and NF of the LNA can be dynamically controlled by adjusting the bleeding current. The fabricated LNA shows the bandwidth of 2.5 GHz. The high gain mode shows 17.5 dB gain with $1.7{\sim}2.8\;dB$ NF and consumes 27 mW power and the low gain mode has 14 dB gain with $2.7{\sim}4.0\;dB$ NF and dissipates 1.8 mW from 1.8 V supply.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.11
• /
• pp.101-106
• /
• 2014

This paper presents a wide dynamic range radio-frequency (RF) root-mean-square (RMS) power detector using an automatic gain control (AGC) loop. The AGC loop consists of a variable gain amplifier (VGA), RMS conversion block and gain control block. The VGA exploits dB-linear gain characteristic of the cascade VGA. The proposed circuit utilizes full-wave squaring and generates a DC voltage proportional to the RMS of an input RF signal. The proposed RMS power detector operates from 500MHz to 5GHz. The detecting input signal range is from 0 dBm to -70 dBm or more with a conversion gain of -4.53 mV/dBm. The proposed RMS power detector is designed in a 65-nm 1.2-V CMOS process, and dissipates a power of 5 mW. The total active area is $0.0097mm^2$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.9
• /
• pp.1-7
• /
• 2008

This paper proposes 3.3V input and 1.8V output voltage mode step-down DC-DC buck converter for wireless mobile system which is designed in a standard 0.35$\mu$m CMOS process. The proposed capacitor multiplier method can minimize error amplifier compensation block size by 30%. It allows the compensation block of DC-DC converter be easily integrated on a chip. Also, we improve efficiency to 3% using low power buffer. Measurement result shows that the circuit has less than 1.17% output ripple voltage and maximum 83.9% power efficiency.

• Proceedings of the KIPE Conference
• /
• 2013.11a
• /
• pp.29-30
• /
• 2013

본 논문에서는 수중통신용 Parametric Array Transducer를 구동하기 위한 고효율 전력증폭기를 제안한다. 수중전력증폭기는 증폭부와 전원부로 나뉘며 증폭부는 Class B push-pull type의 전력증폭기를 사용하며 전력증폭기 구동을 위한 전원부는 기존의 일정전압이 아닌 가변전압을 얻는 Phase-shifted PWM AC/DC 컨버터를 사용하여 고효율로 동작한다. 증폭부는 Class B push-pull type 증폭기를 사용함으로써 뛰어난 선형성이 보장되며 전원 또한 ET(Envelope Tracking)기술을 적용한 가변전압 AC/DC컨버터를 사용하여 고효율로 동작한다. 본 논문에서는 고 효율 수중전력증폭기와 가변전압 AC/DC컨버터의 전력회로를 제시하고 시뮬레이션과 실험을 통하여 특성을 확인하였으며, 수중음향센서를 위한 전력증폭기로 유용하게 사용 될 것을 예상한다.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1995.10a
• /
• pp.18-23
• /
• 1995

The study was carried out to develope a precision positioning apparatus, consisting of DC servo motor and piezoelectric actuator. This system is composed of fine and coarse apparatus, measurement system and control system, Piezoelectric actuator is designed for fine positioning. Coarse positioning using lead screw is drived by DC servo motor. Control system output a signal from laser interferometer and microsense to amplifier of DC servo motor and piezoelectric actuator after digital signal processing(DSP). Resolution of this apparatus measure with laser interferometor and microsense

• Proceedings of the KIPE Conference
• /
• 2015.11a
• /
• pp.161-162
• /
• 2015

본 논문은 수중음향센서용 전력증폭기를 위한 멀티레벨 가변 출력전압 AC/DC 컨버터를 제안한다. 제안하는 AC/DC 컨버터는 멀티레벨 가변출력전압을 얻기 위해 2개의 flying-capacitor 3-level converters와 하나의 다이오드 브리지 회로로 구성되어 있다. 또한 본 논문에서는 제안하는 AC/DC 컨버터의 상세 회로도와 설계 가이드라인을 제시하였다.