• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2003.11a
• /
• pp.169-173
• /
• 2003

This paper analyzes the effects of various operating voltages on the electrical and light output characteristics of 20mW(5mm-Ф), 1W and 5W high-power RGB LEDs. Operating voltages of three types are compared on a simple LED circuit: DC, full-wave rectified DC. and square-wave DC. As a result, it is found that the 1W and 5W high-power LEDs should be provided with appropriate heat sinks that hold down the increase of junction temperature. As for the operating efficiency the case of full-wave rectification gives the highest value.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.491-499
• /
• 2019

Recently, there has been increasing demand for power quality in power supply devices. The IEC 61000-3-2 standard requires that the AC / DC power supply for lighting meet the specifications for the power factor (PF) and total waveform distortion (THD). In addition, advanced countries in Europe are regulating the ripple rate as 15 ~ 30% for the flicker phenomenon caused by the change in the amount of foot energy due to the change in current of the output terminal. Therefore, domestic standards and regulations are being updated. This study adopted the Flyback converter to satisfy the PFC standard, and has the circuit first and second insulation function. To reduce the low frequency ripple of the LED current, Flyback, Coupled Inductor, LC parallel resonance filter, LLC resonance filter, and Cuk were simulated by PSIM to mimic each LED driving circuit. A coupled LC resonant circuit with a coupled inductor on the primary side and LC resonance on the secondary side was also proposed for output side ripple reduction.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.246-247
• /
• 2012

역률개선용 AC/DC Flyback 컨버터의 경우 우수한 역률을 획득할 수 있으나 코어손실이 크고 효율이 낮으며 반면 Forward 컨버터의 경우 코어손실이 작아 높은 효율을 획득할 수 있으나 Dead zone이 존재하여 고역률 획득이 어려운 단점을 갖는다. 따라서 본 논문에서는 Forward 컨버터와 Flyback 컨버터의 장점을 동시에 구현할 수 있는 고효율 및 고역률 Balanced forward-flyback 컨버터를 제안한다. 제안된 컨버터는 스위치 온 시 Forward 컨버터로 동작하며 스위치 오프 시 트랜스포머 자화인덕터 리셋을 위해 Flyback 컨버터로 동작하므로 고역률 및 고효율 획득이 가능하며 Forward 및 Flyback 컨버터가 다루는 에너지량이 전류평형 캐패시터에 의해 항상 절반씩 배분되므로 AC입력전압의 크기에 관계없이 항상 고효율 획득이 가능하다. 제안된 회로의 타당성 검증을 위해 이론적 분석결과와 24W급 LED 조명 회로에 적용한 실험결과를 제시한다.

• Proceedings of the KACD Conference
• /
• 2003.11a
• /
• pp.576-577
• /
• 2003

I. Objectives This study investigated the dentin shear bond strength and the degree of conversion (DC) of currently used dentin bonding agents (DBAs) that were irradiated with a light emitting diode (LED) light curing unit (LCU) and a halogen LCU. II. Materials and methods The halogen LCU and the LED LCU used in this study were a VIP(Bisco, Schaumburg, IL, USA) and an Elipar Freelight(3M ESPE, St Paul, MN, USA) respectively. For the VIP, $400mW{\cdot}cm-2$ intensity mode was used to adjust to the intensity of the LED LCU. The DBAs used in this study were Scotchbond Multipurpose (3M ESPE), Single Bond (3M ESPE), One-step(Bisco), Clearfil SE Bond(Kuraray), and Adper Prompt(3M ESPE).(omitted)

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.572-572
• /
• 2013

본 연구에서는 Plasma damage-free 선형 대향 타겟 스퍼터(Linear Facing Target sputtering: LFTS) 시스템을 이용하여 성막시킨 GaN-LED의 투명전극용 Ga-doped ZnO (GZO) 박막의 특성을 연구하였다. LFTS 시스템을 이용한 GZO 성막 공정 중 LED소자의 플라즈마 노출에 의한 데미지를 최소화 하기 위해 일정한 타겟간 거리(Target-to-Target distance: 65 mm)에서 타겟과 기판간 거리(Target-to-Substrate distance)를 50 mm에서 120 mm로 변화시키며 GZO 투명 전극을 성막해 박막의 특성과 소자의 특성을 동시에 분석하였다. LFTS에서 플라즈마는 GZO 타겟 사이에 형성된 일방향의 자장에 의해 효과적으로 구속되기 때문에 기판과 타겟 거리를 최적화 할 경우 플라즈마 데미지를 최소화하며 GaN-LED의 제작이 가능하다. 기판과 타겟 사이의 거리가 120 mm에서 최적화된 200 nm 두께의 GZO 투명 전극은 DC 파워 250 W, 공정 압력 0.3 mTorr, Ar 20 sccm 실험 조건하에서 LED 소자 위해 성막되었으며, 이후 $600^{\circ}C$ 수소 분위기에서 1분간 급속 열처리하였고 면저항(37 Ohm/sq.)과 450 nm 파장에서의 투과도(83%)를 나타냄을 확인할 수 있었다. LED 소자와 타겟 사이의 거리가 50 mm에서 120 mm로 증가할수록 성막공정 중 LED 소자에 미치는 플라즈마 데미지의 감소로 인해 GaN-LED 소자의 turn on voltage가 8.2 V에서 3.4 V로 감소한 것을 확인하였으며, 또한 radiant intensity는 20 mA의 전류를 인가하였을 시 0.02 mW/sr에서 8 mW/sr로 400배 향상되었다. 이러한 소자 특성은 대향 타겟 스퍼터 시스템으로 성장시킨 GZO 투명전극이 LED 소자의 투명 전극 층(Transparent Conductive Layer: TCL)에 적용될 수 있음을 말해준다.

• Journal of the Korea Society of Computer and Information
• /
• v.16 no.1
• /
• pp.11-18
• /
• 2011

This study developed a digital security device which power is on/off by the RFID card. This device is based on the wireless data transmit/receive circuits, built in RS-232C chip and applied to computer and other digital devices. We can check whether this device is operated or not by connecting the LED. In this system, 13.56MHz frequency circuit supplies power with ID card, and DC inputs check the proximity operating distance of the card field for verifying the existence of a card. The security level of this system is much stronger than that of a compared system[13]. Anyone cannot use the system without RFID card. All illegal access is prevented except for authorized path.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.6
• /
• pp.250-254
• /
• 2011

NiO-AZO films were deposited on glass substrate by DC and RF magnetron co-sputtering system in pure $O_2$ gas without substrate heating during deposition. In order to control the chemical composition of the film, NiO target was supplied with constant RF power of 150 W and AZO target (doped with 2.98 at% aluminum) with DC power varied between 40 W to 80 W. Deposited NiO-AZO films were evaluated by structural and chemical analysis. With introducing AZO, XRD and XPS data reveal that NiO were supplied with more oxygen. these results could be strongly affected by the higher bond enthalpy of NiO compared to ZnO, which makes it possible for NiO to obtain excessive oxygen from ZnO.

• Journal of the Semiconductor & Display Technology
• /
• v.13 no.4
• /
• pp.59-63
• /
• 2014

Previous studies have selected wireless power transmission system using 2.45 GHz of ISM band, but the researches for 5.8 GHz microwave wireless power transmission have been relatively rare. The 5.8 GHz has some advantages compared with 2.45 GHz. Those are smaller antenna and smaller integrated system for RFIC. In this paper, the 5.8 GHz wireless power transmission system was developed and transmission efficiency was measured according to the distance. A transmitter sent the amplified microwaves through an antenna amplified by a power amplifier of 1W for 5.8 GHz, and a receiver was converted to DC from RF through a RF-DC Converter. In the 1W 5.8GHz wireless power transmission system, the converted currents and voltages were measured to evaluate transmission efficiency at each distance where LED lights up to 1m. The RF-DC Converter is designed and fabricated by impedance matching using full-wave rectifier circuit. The transmission-efficiency of the system shows from 1.05% at 0cm to 0.095% at 100cm by distance.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.5
• /
• pp.492-500
• /
• 2013

A balanced forward-flyback converter for high efficiency and high power factor using a foward and flyback converter topologies is proposed in this paper. The conventional AC/DC flyback converter can achieve a good power factor but it has the high offset current through the transformer magnetizing inductor, which results in a large core loss and low power conversion efficiency. And, the conventional forward converter can achieve the good power conversion efficiency with the aid of the low core loss but the input current dead zone near zero cross AC input voltage deteriorates the power factor. On the other hand, since the proposed converter can operate as the forward and flyback converters during switch turn-on and turn-off periods, respectively, it cannot only perform the power transfer during an entire switching period but also achieve the high power factor due to the flyback operation. Moreover, since the current balanced capacitor can minimize the offset current through the transformer magnetizing inductor regardless of the AC input voltage, the core loss and volume of the transformer can be minimized. Therefore, the proposed converter features a high efficiency and high power factor. To confirm the validity of the proposed converter, theoretical analysis and experimental results from a prototype of 24W LED driver are presented.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.431-432
• /
• 2014

Recently, the demand of LED(light-emitting diode) lighting is gradually enlarged by governmental saveenergy policy, which the LED lighting has been established compulsorily in new buildings, public institutions, and residential installations etc.. The LED lighting is driven by SMPS (switching mode power supply). The SMPS requires high efficiency because the SMPS changes a commercial ac power source to low voltage dc power source. Harmonic components that occur in the conversion process of SMPS decrease system power factor and deal great damage in electric power system. To improve such problems, this paper proposes a SMPS of high efficiency. The switching devices in the proposed SMPS are operated by soft switching technique using a new quasi-resonant circuit. The input ac current waveform in the proposed SMPS becomes a quasi-sinusoidal waveform proportional to the magnitude of input ac voltage under constant switching frequency. As a result, the proposed SMPS obtains low switching power loss and high efficiency, and its input power factor is nearly in unity.