• Journal of Satellite, Information and Communications
• /
• v.10 no.1
• /
• pp.77-82
• /
• 2015

In this paper, we perform a study on LED Fluorescent Lamp applying Circuit Driven Method to Tubular LED Lamp Converter. The energy efficiency of LED fluorescent lamp converter requires exceptional protection circuit design, circuit design and structure, because it can not take advantage of Heat-sink structure of the heightened degree Reflector for Fluorescent Lamp. In this paper, we performed a study on LED fluorescent lamp applying circuit driven method to tubular LED lamp converter, Also, we designs LED lamp and converter which can supply DC power common commercial power source.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.1
• /
• pp.67-75
• /
• 2011

The development of electric vehicle power electronics system control, composed of DC-AC inverters and DC-DC converters, attract much research interest in the modern industry. A DC-AC inverter supplies the high-power motor torques of the propulsion system and utility loads of electric vehicles, whereas a DC-DC converter supplies the conventional low-power and low-voltage loads. However, the need for high-power bidirectional DC-DC converters in future electric vehicles has led to the development of many new topologies of DC-DC converters. The nonlinear control of power converters is an active research area in the field of power electronics. This paper focuses on the use of the fuzzy sliding mode strategy as a control strategy for buck-boost DC-DC converter power supplies in electric vehicles. The proposed fuzzy controller specifies changes in control signals based on the surface and knowledge on surface changes to satisfy the sliding mode stability and attraction conditions. The performance of the proposed fuzzy sliding controller is compared to that of the classical sliding mode controller. The satisfactory simulation results show the efficiency of the proposed control law, which reduces the chattering phenomenon. Moreover, the obtained results prove the robustness of the proposed control law against variations in load resistance and input voltage in the studied converter.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.9
• /
• pp.936-943
• /
• 2003

The miniaturized wireless endoscope consists of CMOS Image sensor, FPGA, LED, Battery, DC to DC Converter, Antenna and Transmitter. FSK transmitter is designed and fabricated with 10 mm(diameter)${\times}$23 mm(thickness) dimension considering the maximum permission exposure(MPE), system size, power consumption, linearity and modulation method. Experimental results is - 3.67 dBm output power level, 20 MHz frequency deviation, and - 99 dBc/Hz(@100 kHz offset) phase noise at 1.2 GHz. From the in-vivo experiment, the designed FSK transmitter has a acceptable capability for wireless endoscope.

• KIPE Magazine
• /
• v.27 no.3
• /
• pp.31-37
• /
• 2022

20세기 디스플레이의 중심에 서 있던 브라운관이 1990년대 이후 PDP나 LCD 등 박형 평판디스플레이로 대체되면서 현재까지 스크린 사이즈의 중대형화, 고해상도화, 저소비전력화, 저가격화 등 다양한 노력들이 지속적으로 이루어져 왔다. 특히 TV와 디스플레이 산업에 있어 우리나라는 2004년 이후 세계 점유율 1위의 위치를 꾸준히 유지해 오고 있으나 2020년에 들어서면서 중국과의 격차가 1%대로 좁혀지고 있는 등 TV 시장에 대한 후발주자의 공세가 점차 거세지고 있다. 이에 따라 LCD에서 OLED나 마이크로 LED 등 차세대 디스플레이로의 사업구조 전환을 서두르고 있으며 후발주자의 추격 또한 만만치 않은 상황에 있다. 이러한 가운데 코로나 19를 계기로 비대면 문화가 확산되면서 IT 제품 수요가 지속적인 강세를 보이고 있으며 TV와 디스플레이도 대형 및 프리미엄 TV를 중심으로 그 수요가 빠르게 확대 개선되고 있는 추세로서 100인치대 내외의 대화면, 8K UHD와 같은 초고해상도, 5-10mm 수준의 초슬림에 대한 요구가 절정을 이루고 있다. 이를 위해 TV와 디스플레이를 구성하는 핵심 요소인 전원장치 또한 고전력밀도와 초솔림화를 위한 많은 연구 개발이 이루어지고 있으며 특히 최근 EU의 에코디자인 규정에 따라 디스플레이의 소비전력과 효율 또한 매우 중요한 이슈로 부각되고 있다. 한편, 최근까지 주류를 이루고 있는 LCD TV와 디스플레이용 전원장치의 경우 역률 개선을 위한 PFC(Power Factor Correction) 단과 LED 백라이트 및 영상보드의 전원공급을 위한 절연형 DC/DC 단으로 구성되며, OLED와 같은 저전압 대전류 디스플레이 소자의 경우 전반적인 전원장치의 구성은 유사하나 비절연형 DC/DC컨버터가 추가적으로 요구되기도 한다. 본고에서는 상기한 바와 같은 최근 추세에 따라 TV 및 디스플레이용 전원장치의 각 구성요소별로 고효율, 고밀도, 초슬림을 위한 전원회로 기술에 대해 간략히 소개한다.

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.4
• /
• pp.416-423
• /
• 2009

Statement of problem: The degree of light attenuation at the time of cementation of the PLV restoration depends on characteristics such as thickness, opacity and shade of the restorations, which interfere with light transmittance and, as a result, may decrease the total energy reaching the luting cement. Purpose: The purpose of this study was to compare the degree of conversion of light-cured resin cements measuring by FT-IR in regard to different thickness, light devices and curing time. Material and methods: In the control group, a clear slide glass (1.0 mm) was positioned between the light cured resin cement and light source. The specimens of ceramics were made with IPS Empress Esthetic. The ceramics were fabricated with varying thicknesses-0.5, 1.0, 1.5 mm with shade ETC1. Rely $X^{TM}$ Veneer with shade A3, light-cured resin cement, was used. Light-activation was conducted through the ceramic using a quartz tungsten halogen curing unit, a light emitting diode curing unit and a plasma arc curing unit. The degree of conversion of the light-cured resin cement was evaluated using FT-IR and OMNIC. One-way ANOVA and Tukey HSD test were used for statistical analysis ($\alpha$< .05). Results: The degree of conversion (DC) of photopolymerization using QTH and LED was higher than results of using PAC in the control group. After polymerization using QTH and LED, the DC results from the different ceramic thickness- 0.5 mm, 1.0 mm, 1.5 mm- did not show a significant difference when compared with those of control group. However, the DC for polymerization using PAC in the 1.5mm ceramic group showed significantly lower DC than those of the control group and 0.5 mm ceramic group (P<.05). At 80s and 160s, the DC of light-cured resin cement beneath 1.0 mm ceramic using LED was significantly higher than at 20s (P<.05). Conclusion: Within the limitation of this study, when adhering PLV to porcelain with a thickness between 0.5-1.5 mm, the use of PAC curing units were not considered however, light cured resin cements were effective when cured for over 40 seconds with QTH or LED curing units. Also, when curing the light cured resin cements with LED, the degree of polymerization was not proportional with the curing time. Curing exceeding a certain curing time, did not significantly affect the degree of polymerization.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1661-1668
• /
• 2016

A fixed off-time controlled high power factor ac-dc LED driver is proposed in this paper, which employs a novel zero-crossing-compensation (ZCC) circuit based on a fixed off-time controlled scheme. Due to the parasitic parameters of the system, the practical waveforms have a dead region. By detecting the zero-crossing boundary, the proposed ZCC circuit compensates the control signal VCOMP within the dead region, and is invalid above this region. With further optimization of the parameters KR and Kτ of the ZCC circuit, the dead zone can be eliminated and lower THD is achieved. Finally, the chip is implemented in HHNEC 0.5μm 5V/40V HVCMOS process, and a prototype circuit, delivering 7~12W of power to several 3-W LED loads, is tested under AC input voltage ranging from 85V to 265V. The test results indicate that the average total harmonic distortion (THD) of the entire system is approximately 10%, with a minimum of 5.5%, and that the power factor is above 0.955, with a maximum of 0.999.

• Journal of Navigation and Port Research
• /
• v.47 no.2
• /
• pp.85-92
• /
• 2023

The hardware of an LED lighting control system for coastal lighting at coastal pier entrance consists of a power supply unit, an AVR control unit, a CLCD output unit, an LED control unit, a scenario selection switch unit, and an operation speed display unit. It is made of an 8-channel. The CPU used ATmega128 and the FET was used to control the current signal. To operate the CPU, DC 12V was converted to DC 5V using a regulator 7805. A heat sink was used to remove heat generated in the FET. By connecting the load LED module to the manufactured 8-channel LED lighting control system, the operation was confirmed through various production scenarios. In addition, a control system was designed to show the most suitable color for the atmosphere of the coastal pier according to the input value of temperature and illumination using a fuzzy control system. Computer simulation was then conducted. Results confirmed that fuzzy control did not need to store many data inputs due to characteristics of artificial intelligence and that it could efficiently represent many output values with simple fuzzy rules.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.254-255
• /
• 2012

본 논문은 부스트 컨버터가 통합된 형태의 Single-Stage AC-DC 컨버터에서 스위치를 통과하는 전류의 정보를 이용하여 일차측 전류 제어 루프를 구성하기 위한 전류 복원 기법을 제안한다. 밸리-필 회로가 추가된 Single-Stage AC-DC 부스트 컨버터 통합형 플라이백 컨버터로 구성된 6W/250mA 출력의 프로토타입을 제작하여 일차측 전류 제어와 전류 복원 기법을 이용하여 일정 전류 제어가 이루어짐을 확인하였다.

• Journal of Institute of Convergence Technology
• /
• v.3 no.1
• /
• pp.37-40
• /
• 2013

Plant factory industry as a new agriculture is in the spotlight. In this paper, we experimented plant factory applied photovoltaic system and LED lighting. For growing the plant, red, blue and white LED were placed into 1:4:3. Electric power generated by the photovoltaic system was supplied on DC power supply instead of AC. The designed and experimented power generation amount per day of photovoltaic system were 2,860 Wh and 2,272 Wh respectively. Plant has not been grown at the dead space of LED lighting so it is required to array LED lighting.

• Proceedings of the KAIS Fall Conference
• /
• 2010.05a
• /
• pp.349-352
• /
• 2010

본 논문은 LCD LED 백라이트의 정전류 구동 전원공급 장치를 제안한다. 백라이트로 이용되는 LED의 밝기는 LED로 흐르는 전류에 거의 선형적으로 비례하기 때문에 일정한 밝기를 얻기 위해서는 LED에 정전류가 공급되어야 한다. 제안된 전원공급 장치는 구현이 용이하며 간단한 LED 전류제어 방식을 이용하였으며, 200V의 직류 최대 출력전압과 20W의 최대출력전력을 가진다. 그리고 제안된 회로는 컴퓨터 시뮬레이션을 통하여 회로 동작의 정확함을 보인다.