• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1990년도 추계학술대회 논문집 학회본부
• /
• pp.366-370
• /
• 1990

Generally, when servo system is used, various sensors are required to have comparison and compensation to the reference value. However, the sensors are relatively expensive, and cannot be always implemented because of the limit of space or the environmental conditions. In this paper, state observer systems without sensors are investigated. State observer systems are required to estimate the states quickly and exactly without being affected by the disturbances. Thus, in this paper, the effects of systems poles and observer poles are studies. In addition, the parameter variations are also considered to evaluate the effect of them to the observer based systems. Also, in this paper a whole system which includes compensators, observers and loads are considered and analysed by using numerical simulations.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 A
• /
• pp.124-126
• /
• 1996

In this paper, the driving systems of the Fiber Optic Gyrocompass absolutely required a constant speed and a precise position control with fine step angle, are presented. One of the proposed systems is a stepping motor system with microstep driver, another one is a DC servo motor. Experimental results indicate that a low cost and simple FOG driving system using a stepping motor is capable of a satisfactory operation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 하계학술대회 논문집
• /
• pp.555-558
• /
• 1991

The IESF(Integral Error and State Feedback) controller, which incorporates state feedback as a modern control scheme and integral action as a classical control scheme, has better performance than that of the conventional PID controller in linear time-invariant systems. The IESF controller requires the measurement of all the state variables. But, unfortunately, it may be difficult or impossible to measure all state variables in many applications. And the IESF controller is applicable only to pole-assignable linear time-invariant system without time delay. In this paper, new IESF controller structure was proposed which performs feedback with only measurable state variables. In order to estimate the unmeasurable state variables. It was adopted the filter mode by full-order obserber. The good performance and effectiveness of the proposed controller was confirmed by computer simulation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 추계학술대회 논문집 학회본부
• /
• pp.76-79
• /
• 1988

The sliding mode control in an effective method to eatablish robustness against parameter variation and disturbance. But. In sliding mode strategy, the control function is discontinuous on the hyperplane. However the discontinuous change in control structure caves the controller input to chaffer and gives non-zero steady state error. Consequently, a multiloop feedback control system supplemented by a complelmentary controller is used to improved the drive performence of a DC servo motor and reduce sensitivity to parameter variation, nonlinear effects, and other disturbances.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1988년도 추계학술대회 논문집 학회본부
• /
• pp.426-429
• /
• 1988

A Microprocessor Based Digital Control System is inherently contained a control lag for processing the control program and a data detection time lag. This two types of time lag may cause the system to become unstable. In this paper proposed predictive state observer is used to solve the two time lag problems. I-P control algorithm is used to attain deadbeat response by adjusting the observer gain to overcome the parameter variation or with disturbance. The speed response shows good performance through computer simulation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 B
• /
• pp.897-899
• /
• 1999

This paper presents a scaling factor tuning method to improve the performance of fuzzy logic controller. Tuning rules and reasoning are utilized off-line to determine the scaling factors based on absolute value of the error and its difference. In this paper We proposed a new method to generate fuzzy logic controllers throught genetic algorithm. The developed approach is subsequently applied to the design of proportional plus integral type fuzzy controller for a dc-servo motor control system. The performance of this control system is demonstrated higher than a conventional fuzzy logic controller(FLC).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 A
• /
• pp.391-393
• /
• 1992

This paper proposes an adaptive control system using a 80286 microprocessor-based system and DC servo motors for the control of flexible joint manipulator. In this paper, we construct the controller based on a singular perturbation strategy damping out the elastic oscillations at the joints. we added to the controller the compensator for damping the joint and the term for decreasing the position error between the actuator and the link in order to improve the asymptotical convergence of the position of the link. It is shown that the implementation of this control algorithm can be practical.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 B
• /
• pp.564-566
• /
• 1998

A robot manipulator is a nonlinear time varying MIMO system. Therefore, when a robot manipulator operates at high speeds, the performance of pursuing its trace becomes worse due to the increased nonlinearity of system. Several nonlinear control methods are introduced for solving this problem. But, these methods need a large amount of calculations, so it is necessary to use the controller equipped with a faster and more efficient processing ability. In this paper, we designed the Rhino XR-3 Robot Controller which controls five joints concurrently. To reduce the size of the controller and to control 6 dc-servo motors in real time, we use the TMS320c31, the high-speed digital signal processor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 B
• /
• pp.807-809
• /
• 1995

In this paper, a design of the sliding mode controller using neural networks is proposed. The overall control system consists of a neural network controller and a reaching mode control input. The neural network controller approximates the equivalent control on the sliding surface and reaching mode control input is used to bend the entire system trajectories toward the sliding surface. The proposed controller is applied to the position control of a DC servo motor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 B
• /
• pp.742-744
• /
• 1995

In position control system using variable structure control, the velocity of control object is controlled to approach the desired specified velocity patterns, and eventually the position of control object is correctly at reference position. Here, this intention can be success by means of variable structure control. In this paper, the PI velocity feedback control is also used sliding mode controller. The design of position controller under specified velocity profiles in variable structure control's constraints is studied.