• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.223-223
• /
• 2011

적외선 감지기로 사용되는 microbolometer 소자재료로 VOx 또는 비정질 Si이 가장 많이 사용된다. 그 중에서 VOx 물질은 온도저항계수 즉, TCR이 높고 감지도가 우수하기 때문에 비냉각 적외선 검출기에 많이 응용된다. Microbolometer 검출기는 그 응답도는 micromachining 공정에 의해 좌우되는 열 고립구조에 의해 좌우된다. 특히 TCR 값이 크고, 열시상수 값이 작을수록 양질의 감지도를 얻을 수 있으므로 재료의 선택 및 공정이 매우 중요하다. 따라서 본 연구에서는 비냉각 적외선 감지소자로 사용되는 VOx 박막을 DC Sputtering을 사용하여 증착하였으며, 그 특성을 조사하였다. MEMS 공정에 의한 센서의 제작은 적외선을 흡수하여 저항변화를 읽어내어 판독하는 Readout IC(ROIC) 위에 행해진다. Monolithic 공정에 의해 이러한 ROIC 위에서 공정이 동시에 행해지므로 공정온도는 매우 중요한 요소로 작용한다. 따라서 증착된 VOx 박막의 열처리 효과를 연구하였다. 열처리 온도는 $250^{\circ}{\sim}420^{\circ}C$, 열처리 시간은 20~80 min 까지 변화시켰다. 갓 증착된 VOx 박막의 저항은 약 200 $k{\Omega}$이였으며, TCR은 -1.5%/$^{\circ}C$로 나타났다. 열처리 온도가 증가함에 따라 TCR 값은 증가하였으며, 열처리 시간이 증가할수록 역시 TCR 값이 증가하는 경향을 보였다. 열처리 온도 320$^{\circ}C$, 열처리 시간 40 min에서 TCR 값은 약 -2%/$^{\circ}C$의 값을 얻을 수 있었다. 이러한 성능의 VOx 박막을 이용하여 비냉각형 microbolometer 검출소자를 열변형없이 공정을 수행할 수 있을 것으로 기대한다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 초전도 자성체 연구회
• /
• pp.69-72
• /
• 2003

Bi-2223 superconducting wires were fabricated by stacking, drawing process with different precursor powders and different heat-treatment histories. The precursor powders were 2 kinds of Pb content. And a part of the tapes were experienced pre-annealing process which caused tetragonal structure of Bi-2212 phase to orthorhombic structure of it was during drawing process. We confirmed the transformation of Bi-2212 phase from tetragonal structure to orthorhombic structure and reduction of second phases. XRD and DC magnetization analysis were performed in order to investigate the fraction of Bi-2223 phase in Bi-2223/Ag HTS tape. We could achieve best Ic of 70 A class at the Bi-2223/Ag tape using low Pb content of precursor powder and experienced pre-annealing process. DC magnetization analysis was useful to investigate the fraction of Bi-2223 phase in the Bi-2223/Ag tape.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 하계학술대회 논문집
• /
• pp.280-282
• /
• 2007

기존 PDP 전원 시스템은 일반적으로 두 개의 절연형 Transformer 를 사용하여 유지전원($V_S$)과 어드레스 전원($V_A$), Multi단 전원($V_M$) 으로 구성된다. 이들 각 전력 변환 회로에 Transformer 및 제어 IC 가 사용되므로, 효율 저감 및 원가 상승, 소자 스트레스 등의 단점을 가지고 있다. 본 논문에서는 절연형 Transformer 한 개로 PDP 전원시스템을 구동하는 방식에 대해 제안한다. 제안된 방식은 DC/DC 전력단의 고효율 동작 및 신뢰성 개선은 물론 부피, 크기를 줄여 원가 저감에 기여한다. 또한, 제안된 방식은 PDP 구동 방식의 하나인 Address Display Separation Method (ADSM) 에 적합하다. 기존 방식과 제안된 방식을 비교하고 이론적 분석과 실험을 통해 제안된 방식의 우수성을 확인 하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2015년도 전력전자학술대회 논문집
• /
• pp.401-402
• /
• 2015

In this paper a direct cell-to-cell charge balancing circuit which can transfer the charge from any cell to any cell in the battery string is introduced. In the proposed topology the energy in the high voltage cell is transferred to the low voltage cell through the simple operation of a dc-dc converter to get fast equalization. Furthermore, the charge equalization can be performed regardless of the battery module operation whether it is being charged, discharged or relaxed. The monitoring circuit composed of a DSP and a battery monitoring IC is designed to monitor the cell voltage and protect the battery. In order to demonstrate the advantages of the proposed topology, a prototype circuit was designed and applied to 12 Lithium-Ion battery module. It has been verified with the experiments that the charge equalization time of the proposed method was shortest compared with those of other methods.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2015년도 추계학술대회 논문집
• /
• pp.7-8
• /
• 2015

In this paper a cell-to-cell fast charge balancing circuit for the Lithium-Ion battery module is proposed. In the proposed topology the energy in a high voltage cell is transferred directly to a low voltage cell through the operation of the dc-dc converter. Furthermore, the charge balancing can be performed regardless of the battery operation whether it is being charged, discharged or relaxed. The monitoring circuit composed of a DSP and a battery monitoring IC is designed to monitor the cell voltage and detect the inferior cell thereby protecting the battery module from failure. In order to demonstrate the performance of the proposed topology, a prototype circuit was designed and applied to 12 Lithium-Ion battery module. It has been verified with the experiments that the charge equalization time of the proposed method was shorter compared with those of other methods.

• Corrosion Science and Technology
• /
• 제9권6호
• /
• pp.276-280
• /
• 2010

Copper(Cu) as an interconnecting metal layer can replace aluminum (Al) in IC fabrication since Cu has low electrical resistivity, showing high immunity to electromigration compared to Al. However, it is very difficult for copper to be patterned by the dry etching processes. The chemical mechanical polishing (CMP) process has been introduced and widely used as the mainstream patterning technique for Cu in the fabrication of deep submicron integrated circuits in light of its capability to reduce surface roughness. But this process leaves a large amount of residues on the wafer surface, which must be removed by the post-CMP cleaning processes. Copper corrosion is one of the critical issues for the copper metallization process. Thus, in order to understand the copper corrosion problems in post-CMP cleaning solutions and study the effects of DC biases and post-CMP cleaning solution concentrations on the Cu film, a constant voltage was supplied at various concentrations, and then the output currents were measured and recorded with time. Most of the cases, the current was steadily decreased (i.e. resistance was increased by the oxidation). In the lowest concentration case only, the current was steadily increased with the scarce fluctuations. The higher the constant supplied DC voltage values, the higher the initial output current and the saturated current values. However the time to be taken for it to be saturated was almost the same for all the DC supplied voltage values. It was indicated that the oxide formation was not dependent on the supplied voltage values and 1 V was more than enough to form the oxide. With applied voltages lower than 3 V combined with any concentration, the perforation through the oxide film rarely took place due to the insufficient driving force (voltage) and the copper oxidation ceased. However, with the voltage higher than 3 V, the copper ions were started to diffuse out through the oxide film and thus made pores to be formed on the oxide surface, causing the current to increase and a part of the exposed copper film inside the pores gets back to be oxidized and the rest of it was remained without any further oxidation, causing the current back to decrease a little bit. With increasing the applied DC bias value, the shorter time to be taken for copper ions to be diffused out through the copper oxide film. From the discussions above, it could be concluded that the oxide film was formed and grown by the copper ion diffusion first and then the reaction with any oxidant in the post-CMP cleaning solution.

• 생명과학회지
• /
• 제26권8호
• /
• pp.936-942
• /
• 2016

본 연구는 초피의 항균 활성 소재의 산업화 타진 연구로 초피과피 정유 성분의 경우 높은 생산단가로 인해 그 활용이 제한적이다. 이에 초피잎을 대상으로 항균 활성소재를 탐색하고 초피의 천연 방향성과 항균력을 이용하여 실내 환경 개선 소재 특히 친환경 항균블라인드 개발에 대한 활용 가능성을 타진하였다. 그 결과, 초피잎 추출물의 항균 활성은 초피과피 추출물보다 약하게 나타났지만, K. pneumoniae, S. aureus와 S.mutans 균에 대하여 IC₅₀ 값은 0.5 mg/ml, 0.1 mg/ml와 1.0 mg/ml로 운향과 유래 타 Zanthoxylum 속 보다 항균력이 강한 것으로 나타났다. 항균력이 강하게 확인된 초피잎 EtOH 추출물과 EtOAc 추출물의 GC-MS 분석을 통해 초피잎 유래의 항균력 관련 화합물로서 quinic acid, 3,5-dihydroxy-6-methyl-2,3-dihydro-4H-pyran-4-one과 kaempferol 등을 확인할 수 있었다. 또한, International Standard Fabrics Test Method에 준하여 초피 추출물을 처리한 블라인드 소재의 항균력을 조사한 결과, 1% 농도의 초피잎 EtOH 추출물을 처리한 직물 블라인드 소재의 경우는 항생제 내성균 S. aureus의 생육을 99.9% 저해하였고, 2% 농도의 처리에 의해서는 K. pneumoniae 생육도 완전히 저해하였다. 이러한 연구결과는, 고가인 초피과피에 비해 농산폐자원으로 폐기되고 있는 초피잎의 항균력을 이용하여 친환경 기능성 항균 직물 블라인드 및 실내 창호 소재를 개발한다면 최근 급증하는 실내 환경성 질환의 예방 및 제어에 매우 유용할 수 있음을 시사한다.

• 한국진공학회지
• /
• 제7권s1호
• /
• pp.167-170
• /
• 1998

To apply diamond films in microelectromechanical systems(MEMS), it is necessary to develop the patterning technologies of diamond films in the micrometer scale. In this paper, three different kinds of technologies for patterning CVD diamond films carried out by us were demonstrated: selective growth by improved diamond nucleation in DC bias-enhanced microwave plasma chemical vapor deposition (MPCVD) system, selective growth of seeding using diamond-particle-mixed photoresist, and selective etching of oxygen ion beam using Al as the mask. It was show that high selectivity and precise patterns had been achieved, and all the processes were compatible with IC process.

• 한국정보기술응용학회:학술대회논문집
• /
• 한국정보기술응용학회 2005년도 6th 2005 International Conference on Computers, Communications and System
• /
• pp.187-190
• /
• 2005

Ultra wideband (UWB) technologies have been developed to exploit a new spectrum resource in substances and to realize ultra-high-speed communication, high precision geolocation, and other applications. The energy of UWB signal is extremely spread from near DC to a few GHz. This means that the interference between conventional narrowband systems and UWB systems is inevitable. However, the interference effects had not previously been studied from UWB wireless systems to conventional mobile wireless systems sharing the frequency bands such as WCDMA system. This paper experimentally evaluates the interference from two kinds of UWB sources, namely a direct-sequence spread-spectrum UWB source and an impulse radio UWB source, to a WCDMA digital transmission system. The average frame error rate degradations are presented. From these experimental results, we show that in all practical cases UWB system can coexist with WCDMA terminal without causing any dangerous interference.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.101-103
• /
• 2003

This paper presents the speed control of Brushless DC Motors using PI control. PI control is implemented by software using digital signal processor(DSP) TMS320F240 from Texas instruments. Considering the cost of BLDC Driver A. B. C phase hall IC's signal is used instead of incremental encoder. The Present paper describes, how to control a speed of BLDC Drive.