• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.291-292
• /
• 2019

본 논문에서는 AC 센서를 사용하는 전기자전거용 탭 인덕터 부스트 컨버터 시스템을 제안한다. 일반적으로 인덕터 전류 측정을 위해서는 DC 센서를 사용한다. 왜냐하면, AC 센서를 사용하여서 인덕터 평균 전류 크기를 측정하면 평균 전류 크기가 0이기 때문에 실효성이 있는 평균 전류 크기를 측정할 수 없다. 하지만 탭 인덕터 부스트 컨버터의 경우에는 부스트 컨버터 스위치가 닫혔을 때와 열렸을 때의 인덕터값이 달라져서 AC 센서로 측정되는 인덕터 전류 크기가 0이 아니고 AC 센서 측정값과 탭 인덕터의 턴 비를 이를 이용하여 간단한 계산을 통해 인덕터에 흐르는 평균 입력 전류 크기를 계산할 수 있다. 알 수 있다. 제안되는 시스템은 프로토타입 하드웨어로 설계되었으며 본문의 실험을 통해서 검증되었다.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.293-294
• /
• 2019

본 논문은 입출력 전력품질이 우수하고 전압별 시리즈화가 용이한 고전압 대용량 전동기 구동용 H-브릿지 멀티레벨 컨버터의 직류 전압 변동 억제를 위한 전압변조 방법에 관하여 기술하였다. H-브릿지 멀티레벨 컨버터의 Phase-shifted PWM에 의해서 전동기 무부하 구동 조건에서 유효전력이 Negative로 전이해서 전력이 전동기에서 컨버터로 유입되어 특정 파워 셀 직류 전압이 상승하는 현상이 발생한다. 따라서, 개발 파워 셀 위상 전이량을 일정 주기마다 변경하여 회생된 에너지를 H-브릿지 멀티레벨 컨버터의 모든 파워 셀에 분산시켜 파워 셀 직류 전압 상승을 억제하였다. 제안된 방법의 타당성과 실용성은 실용량 제품의 현장 적용 시험을 통하여 입증하였다.

• Proceedings of the KIPE Conference
• /
• 2018.11a
• /
• pp.56-58
• /
• 2018

본 논문에서는 낮은 스위치 전압정격과 넓은 전압범위를 갖는 800V/14V LDC용 새로운 소프트 스위칭 컨버터를 제안한다. 제안하는 컨버터는 입력이 직렬구조로써 입력전압의 절반으로 낮은 스위치의 전압정격을 갖기 때문에 600V의 Si-MOSFET를 사용할 수 있어 도통손실을 줄일 수 있으며 넓은 입력전압 및 부하영역에서 소프트 스위칭을 성취하여 높은 효율을 달성할 수 있고 변압기의 직렬연결로 된 커패시터로 인해 자화전류의 오프셋이 없다. 또한 2차 측의 DC 블로킹 커패시터에 인터리빙 방식을 적용하여 기존의 전류정격이 큰 문제를 해결하였다. 제안하는 소프트 스위칭 컨버터의 동작원리를 제시하고 시작품을 통해 본 논문의 타당성을 검증하였다.

• Proceedings of the KIPE Conference
• /
• 2018.11a
• /
• pp.59-61
• /
• 2018

본 논문에서는 입력전류를 센싱 받지 않아도 역률 보상을 하는 새로운 단일단 브리지리스 AC-DC컨버터를 제안한다. 제안하는 컨버터의 스위치는 전구간에서 ZVS(Zero Voltage Switching) 턴 온을 성취하며, 다이오드는 전구간에서 ZCS(Zero Current Switching) 턴 오프를 성취한다. 제안하는 컨버터의 넓은 범위의 출력전압 제어와 간단한 전력 제어를 위해 SDAB(Semi-Dual Active Bridge)기반의 모듈레이션 기법을 적용하였다. 1kW급 50kHz의 스위칭 주파수를 갖는 시작품을 통해 본 논문의 타당성을 검증하였다.

• Journal of the Semiconductor & Display Technology
• /
• v.18 no.1
• /
• pp.21-24
• /
• 2019

In this paper, 5.8GHz 25W microwave wireless power transmission system was developed. The transmission system is composed of a signal generator, a 1W drive amplifier, a 25W power amplifier, and a circularly polarized transmission antenna. The receiving system was fabricated with an integrated receiver that combines a circularly polarized receiving antenna, a pass band filter, and an RF-DC converter. And a multi-integrated receiver had twelve parts, including an integrated receiver. Under the conditions, voltage and current were measured for the system at 5cm intervals from a minimum distance of 5cm to a maximum distance of 80cm. The power was calculated for the system. The results of the system are shown in tables and graphs. The power decreases with distance, but the power does not drop sharply due to a multi-integrated receiver.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.4
• /
• pp.294-297
• /
• 2021

A grid voltage estimation method for modular plug-in active power decoupling (APD) circuits is proposed in this study as direct replacements of electrolytic capacitors. Since modular plug-in APD circuits cannot have additional grid voltage sensors and should be operated independently without information exchange with the front-end converter, it is impossible to obtain the phase information of the grid directly. Therefore, the proposed method uses the second-order harmonic component of the DC-link voltage to estimate the grid voltage necessary to control the APD circuit. By employing the proposed method, the concept of modular plug-in APD circuits can be realized and implemented without direct detection of the grid voltage. The experimental results based on hardware-in-the-loop simulation (HILS) validate the effectiveness of the proposed control method.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.286-287
• /
• 2020

본 논문은 단상 전기철도 시스템의 불평형 부하 특성으로 인한 3상 계통의 전력 불평형을 보상하기 위해 백투백 컨버터를 적용하였으며, 실험을 통해 전력 불평형 성능 개선 특성을 검증하였다. 3상 전압은 스코트 변압기를 통해 2개의 M-T상 전압으로 출력되며, 전력 불평형 개선을 위해 적용된 백투백 컨버터는 DC 링크를 공유하며 각각 M-T상에 연계된다. 백투백 컨버터는 M-T상에 연계된 부하용량 차이에 따른 불평형 조건에 관계없이 M상과 T상 계통 라인에 동일한 전력이 공급되도록 제어하는 역할을 수행하며, 제어 알고리즘은 동기좌표계에서 구현하였다. 백투백 컨버터의 프로토 타입은 3레벨 NPC 컨버터로 설계하였으며, M상 5kW, T상 1kW 부하에서 전력보상 장치가 동작하고 있음에도 완전히 해결되지 않은 불평형 현상에 대해 분석한다.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.9
• /
• pp.37-45
• /
• 1999

For the purpose of reducing the output voltage fluctuation of thin film multijunction thermal converter, EVANOHM alloy-S and chromel-alumel thermocouple were used as a thin film heater material and as a thermoelement of thrmopile, respectively. The temperature coefficient of the resistance of thin film EVANOHM alloy-S heater was about $1.4 {\times} 10^4/^{\circ}C$, which is very small compared to other materials, and thin film chromel-alumel thermocouple showed relatively small difference of the Seebeck coefficients about $38 {\mu}V/K$. The output voltage fluctuation of the thermal converter was about 0.06% for the initial 120 seconds in air and decreased considerably after preheating for 5 minutes or more. The respective AC-DC voltage and current transfer error ranges of the thermal converter were about ${\pm}$1.6 ppm and ${\pm}$0.7 ppm in the frequency range from 10Hz to 10 kHz and increased remarkably below 10 Hz or above 10 kHz.

• Journal of Biosystems Engineering
• /
• v.7 no.2
• /
• pp.18-29
• /
• 1983

A low cost and versatile data acquisition system for the field and laboratory use was developed by using a single board microcomputer. Data acquisition system based on a Z80 microprocessor was built, tested and modified to obtain the present functional system. The microcomputer developed consists of 6 kB ROM, 5 kB RAM, 6-seven segment LED display, 16-Hex. key and 8 command key board. And it interfaces with an 8 channel, 12 bits A/D converter, a microprinter, EPROM programmer for 2716, and RS232C interface to transfer data between the system and HP3000 mini-computer manufactured by Hewlett Packard Co., A software package was also developed, tested, and modified for the system. This package included drivers for the AID converter, LED display, key board, microprinter, EPROM programmer, and RS232c interface. All of these programs were written in 280 assembler language and converted to machine codes using a cross assembler by HP3000 computer to the system during modifying stage by data transferring unit of this system, then the machine language wrote to the EPROM by this EPROM programmer. The results are summarized as follows: 1. Measuring program developed was able to control the measuring intervals, No. of channels used, and No. of data, where the maximum measuring speed was 58.8 microsec. 2. Calibration of the system was performed with triangle wave generated by a function generator. The results of calibration agreed well to the test results. 3. The measured data was able to be written into EPROM, then the EPROM data was compared with original data. It took only 75 sec. for the developed program to write the data of 2 kB the EPROM. 4. For the slow speed measurements, microprinter instead of EPROM programmer proved to be useful. It took about 15 min. for microprinter to write the data of 2 kB. 5. Modified data transferring unit was very effective in communicating between the system and HP3000 computer. The required time for data transferring was only 1~2 min. 6. By using DC/DC converting devices such as 78-series, 79-series. and TL497 IC, this system was modified to convert the only one input power sources to the various powers. The available power sources of the system was DC 7~25 V and 1.8 A.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.5
• /
• pp.587-592
• /
• 2018

Because the brightness of an AMOLED is determined by the flowing current, each pixel of AMOLED operates via A current driving method. Therefore, it is necessary to supply power to adjust the amount of current according to THE user's requirement for AMOLED driving. In this study, an IP driver block was designed and a simulation was conducted for an AMOLED display, which supplies power as selected by users. The IP driver design focused on regulating the output power due to the OLED characteristics for the diode electric current according to the voltage to be activated by pulse-skipping mode (PSM) under low loads, and 1.5 MHz pulse-width modulation (PWM) for medium/high loads. The IP driver was designed to eliminate the ringing effects appearing from the dis-continue mode (DCM) of the step-up converter. The ringing effects destroy the power switch within the IC, or increase the EMI to the surrounding elements. The IP driver design minimized this through a ringing killer circuit. Mobile applications were considered to enable true shut-down capability by designing the standby current to fall below $1{\mu}A$ to disable it. The driver proposed in this paper can be applied effectively to the same system as the AMOLED display dual power management circuit.