• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2050-2054
• /
• 1997

본 논문에서는 직류 대 직류 강압형 변환기의 전달함수 변환에 의한 새로운 제어방법을 제안하였다. 제안된 방법을 외란 및 회로변수 값의 번화 시 나타나는 영향을 최소화시키며, 변환기의 동특성에 영향을 미치는 출력필터의 공진과 동작점 변화에 의한 플랜트 특성 변화를 현저하게 개선시킨다. 먼저 전달함수 변환 제어 시 시스템의 특성을 나타내는 여러 가지 전달함수를 구하여, 이를 기존의 직류 대 직류 변환기에서의 전달 함수와 비교하였다. 또한 외란 및 회로변수 값 변화시의 기준 전압 대 출력 전압 전달함수의 민감도를 구하여 회로변수 값 변화 시 나타나는 특성이 개선됨을 보이고, 마지막으로 모의실험과 실험을 실시하여 제안된 제어 방법이 기존의 제어 방법과 비교하여 우수한 성능을 가짐을 보였다.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.83-86
• /
• 2002

This paper presents an implementation of Pill controller for DC-DC converter using the microcontroller. The features of the microcontroller such as the on chip ADC and Pulse width Modulator (PWM) eliminate the external components needed to perform these functions. The duty rate cycle for the DC-DC converter can be updated every time when the (ADC) conversation and the calculation time are finished. The stable response can be obtained for any kind of DC-DC converters. The SMPS controller looks at the converter output, compares the output to a set point, performs a control algorithm (Pill algorithm) and finally applies the algorithm output to the PWM. PWM output is then used to drive the DC-DC converter. Figure (1) shows a simplified block diagram of a complete DC-DC converter system.

• Journal of IKEEE
• /
• v.18 no.2
• /
• pp.220-227
• /
• 2014

This paper presents a control method of Single-Inductor Dual-Output DC-DC Converter using Common mode feedback and differential feedback loops. To generate duty used for differential mode feedback loop, this paper propose relative sawtooth circuit using current divider circuit which makes ramp signal with variable dead-time. Two outputs of the Single-Inductor Dual-Output DC-DC Converter are specified for 2.8 V and 4.2 V with input voltage 2.5 V. The maximum conversion efficiency of designed SIDO DC-DC Converter is 95% at total output power of 539mW. Cross regulations of Boost1 and Boost2 are 3.57% and 4% each, when increasing twice times output current.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.11B
• /
• pp.1667-1675
• /
• 2010

This paper presents a high efficiency DC-DC buck converter for mobile device. The circuit employes simplified compensation circuit for its portability and for high efficiency at stand-by mode. This device operates at PFM mode when it enters stand-by mode(light load). In order to place the compensation circuit on chip, the capacitor multiplier method is employed, such that it can minimize the compensation block size of the error amplifier down to 30%. The measurement results show that the buck converter provides a peak efficiency of 93% on PWM mode, and 92.3% on PFM mode. The converter has been fabricated with a $0.35{\mu}m$ CMOS technology. The input voltage of the buck converter ranges from 2.5V to 3.3V and it generates the output of 3.3V.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.12
• /
• pp.4984-4990
• /
• 2010

In this paper, a Step-down CMOS DC-DC Converter using low power switched capacitor method is designed in a 0.5 ${\mu}m$ technology for the integration of devices. Conventional DC-DC converter is used inductor that can store energy in a magnetic field but have low efficiency because power consumption is caused by magnetic flux. And there were problems with size, weight and price to integrate chip. In this paper, a proposed Inductorless step-down CMOS DC-DC converter of low power using SC method is designed in a 0.5um technology to solve these problems. Designed DC-DC converter have 96% power efficiency with 200kHz frequency by using cadence simulation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.10
• /
• pp.1590-1597
• /
• 1993

Power conversion system generally requires bidirectional converter. A storage energy of reactor is suppressed by regeneration of surplus electic energy in converter to power source. When an electric isolation in the power conversion system is required. the most suitable position for the isolation is the DC-Link part. A transformer in the DC part is minimized because of high repetition frequency. This paper proposes that power conversion system becomes bidirectional DC-DC converter with electric isolation by intergrated voltage control method. It is intergrated voltage control that makes system construciton simple, has control errow little quantity ans gets output response Quick. And the power-switches which should be operated is selected automatically without a detection of the current-direction.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.340-343
• /
• 1990

Recently, Power Electronics system increase makes harmonics and low input power factor problem. In this paper present new analysis method of PWM Boost AC/DC Converter. This PWM AC/DC Converter is capability of unity power factor, control of DC side voltage level, generation, and near sinusoidal current in 3-phase line. The control of this type of converter is widely discussed. And this paper propose new phase convert function and analysis in steady state of system to obtain amplitude and phaser of switching function. This switching function is general solution and it can use in high power approach. And this control method show the clear meaning of control variable. This paper propose new analysis method of Boost AC/DC Converter of steady state and 3-phase 2KW experimental system show its validity.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.2023-2027
• /
• 1997

This paper presents the dynamic analysis and control-loop design of a zero-voltage-switched full bridge (ZVS-FB) PWM dc/dc converter. Based on the small-signal analysis results, the control-loop is designed using a simple two-pole one-zero compensation circuit. Design results are verified by both computer simulations and experimental data obtained from a 2kW prototype converter.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1035-1037
• /
• 1992

Generally, fuel cell has characteristics of low voltage, large current and voltage variation under load change. Therefore, DC output voltage of fuel cell is too low to convert into AC with high efficiency and good performance. For this reason, fuel cell generating system is composed of DC-DC converter and inverter in cascade. This paper used 2-phase boost DC-DC converter to obtain low distortion waveform and reduce input-output current ripple, and discussed inverter which can be operated in independent drive mode and utility line interface drive mode. Then, the change of modes can be achived smoothly.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.474-475
• /
• 2008

Portable device is powered by the battery. To use portable devices longer time without replacing the battery, you should maximize the lifetime of the battery. If you use efficient DC-DC converter, You can maximize the lifetime of the battery.