This paper has relatively high technical standard and experimental skill. The fabrication of TCO film with high transparency, low resistance and low chromaticity require exact control of several competing factors. This paper has resolved these problems reasonably well, thus recommended for publication. Indium tin oxide(ITO) thin films were by D.C. magnetron roll-to-roll sputter system utilizing ITO and $SiO_2$ targets of ITO and $SiO_2$. In this experiment, the effect of D.C. power, winding speed, and oxygen flow rate on electrical and optical properties of ITO thin films were investigated from the view point of sheet resistance, transmittance, and chromaticity($b^*$). The deposition of $SiO_2$ was performed with RF power of 400W, Ar gas of 50 sccm and the deposition of ITO, DC power of 600W, Ar gas of 50 sccm, $O^2$ gas of 0.2 sccm, and winding speed of 0.56m/min. High quality ITO thin films without $SiO_2$ layer had chromaticity of 2.87, sheet resistivity of 400 ohm/square, and transmittance of 88% and $SiO_2$-doped ITO Thin film with chromaticity of 2.01, sheet resistivity of 709 ohm/square, and transmittance of more than 90% were obtained. As a result, $SiO_2$ was coated on PET before deposition of ITO, their chromaticity($b^*$) and transmittance were better than previous results of ITO films. These results show that coating of $SiO_2$ induced arising chromaticity($b^*$) and transmittance. If the thickness of $SiO_2$ is controlled, sheet resistance value of ITO film will be expected to be better for touch screen. A four point probe and spectrophotometer are used to investigate the properties of ITO thin films.
Ketrorolac tromethamine (KT), a nonsteroidal anti-inflammatory drug (NSAID) is required repeated administration due to its short blood half-life. To avoid dose-dependent side effects of KT, sustained-release pellets containing KT were prepared by coating with Eudragit$^{(R)}$ RS 100 and Eudragit$^{(R)}$ NE 30D. The in vitro and in vivo drug release behavior of KT from Eudragit$^{(R)}$ RS 100 and NE 30D coated pellet (SR-A), Eudragit$^{(R)}$ RS 100 coated pellet (SR-B) and conventional commercial immediate-release tablet (IR) was investigated. KT from SR-A and SR-B was slowly released over several hours, whereas IR showed rapid initial release in vitro. The pharmacokinetic study in vivo was performed by oral administration in beagle dogs. 5 mg IR was administered 3 times at intervals 5 hr. Five milligrams of IR was administered 3 times at intervals of 5 hr and 15 mg of SR-A and SR-B did once. After administering IR, KT concentration in blood showed high peak- trough fluctuation and stomach ulcer were discovered. On the other hand, SR-A and SR-B sustainedly released KT and reduced the occurrence of stomach ulcer. There sustained-release pellets will be effective system to minimize dosedependent of side effect and improve patient compliance.
본 연구에서는 도심지 열섬현상을 완화 시킬 수 있는 아크릴 수지와 차열안료를 혼합한 차열성 포장을 개발하였다. 태양 복사열에 의한 포장체의 온도상승을 모사한 실내 시험으로부터 $60^{\circ}C$의 포장 온도에서 차열성 포장이 $12^{\circ}C$ 이상의 온도 저감 효과를 나타냈다. 이러한 온도 감소 효과는 차열안료의 배합비가 증가함에 따라 증가하였고, 반면에 점도의 증가로 인하여 작업성은 떨어졌다. 이러한 결과로부터 아크릴 수지 대비 차열안료의 최적혼합비율을 15%로 결정하였다. 차열성 포장의 칸타브로 손실률은 일반 배수성 포장의 손실률 1/4 수준으로 골재 비산 저항성이 우수하게 나타났다. 휠트랙킹 시험결과 차열성 포장의 동적안정도가 일반 배수성 포장에 비해 두 배 증가하였다. 차열성 포장재의 높은 부착력으로 인하여 탈리에 의한 손상 가능성은 낮은 것으로 나타났다. 시험 시공 구간에서의 소음도 측정 시험 결과 일반 배수성 포장에 비하여 평균 3.7dB의 소음저감 효과가 있었고, 미끄럼 저항치는 일반 배수성 포장에 비해서 평균 30% 정도 높아 우수한 미끄럼 저항성을 가지는 것으로 판단된다. 투수 시험 결과 차열성 포장의 투수성은 일반 배수성 포장보다 다소 작았으나 국내 배수성 포장 기준을 만족하는 것으로 나타났다.
본 연구는 광노화의 원인으로 알려진 자외선을 차단하는 새로운 복합 분체에 관한 것이다. Hydroxyapatite (HAp)는 자체 생체 친화적이고, 피부에 도포 시 백탁 현상 없이 자외선을 차단하는 효과가 우수하다. 그러나 HAp 구조가 단단한 육방정계이어서 피부 도포 시 피부손상과 분체의 재응집 현상이 발생되어 화장 후 뭉치는 현상, 자체 사용감이 매끄럽지 못하는 단점을 가지고 있다. 이러한 문제점을 개선하고자 HAp의 표면 개질을 통한 자외선 차단 증진 및 사용감을 개선한 새로운 복합 분체를 개발하고자 하였다. 본 연구에서 HAp의 표면 개질을 위해 코팅제로 dimethicone, lauroyl lysine, triethoxycaprylylsilane 및 silica를 사용하였다. Dimethicone, lauroyl lysine 및 triethoxycaprylylsilane은 건식 방법으로 각각 표면 복합화 처리하였고, silica는 수열 합성법으로 표면 처리하여 표면 복합체를 제조하였다. 제조된 HAp 복합체의 자외선 차단 효과를 측정하여 실리카가 코팅된 HAp-silica를 최적의 HAp 복합체로 선정하였다. SEM, 입자크기와 분포, 표면 측정, EDS 분석을 통해 HAp-silica의 표면 복합 분체 특성을 조사하였다. 또한 제형 내에서 안정성, BB cream에서 자외선 차단 효과 측정 및 안전성 시험을 실시하였다. 연구 결과, HAp 분체의 표면 개질을 통해 제조한 HAp-silica는 사용감이 우수하였고, 백탁 현상을 개선함으로써 자외선 차단 효과를 증진시키는 복합 분체로서 자외선 차단 화장품의 새로운 기능성 소재로서 응용 가능성이 있음을 확인하였다.
최근 산업이 고속도화, 고능률화 및 고정멸화의 추세로 발전함에 따라 우수한 내마모성, 인성, 고온 안정성 및 내구성을 갖는 공구 및 금형을 요구하게 되었다. 그러나 이와같은 성질들은 어떤 단일 재료에서는 얻을 수 없으며 적당한 기판공구나 금혈위에 내마모성 보호피막을 coating함으로 비교적 저렴하게 얻을 수 있다. 화학증착법으로 TiC, TiN등을 증착시킬때에는 $1000^{\circ}C$정도의 반응온도가 필요하며 이러한 증착온도는 모재가 초경합금일때는 문제가 안되나 강재일 경우 모재의 연화와 칫수변화의 문제를 야기시킨다. 최근에는 플라즈마를 사용하여 증착반응온도를 $550^{\circ}C$ 이하로 낮추는 플라즈마 화학 증착볍(PACVD)이 대두되고 있다. 그러나 이 방법어서 는 뚱착하려는 금속원소가 TiCl4의 형태로 공급되고 있으므로 생성된 층이 염소를 포함하고 있다. 이 층에 잔존하는 염소는 층의 기계적 성질을 저하시키고 층내의 stress를 유발시킨다. 또한 HCI개스의 생성으로 인하여 펌프 및 장비의 부식이 촉진 된다 이러한 결점을 극복하기 위하여 금속유기화합물 전구체(metallo-organic precursor)로 $TiCl_4$를 대체하고자 하는 연구가 활발하게 진행되고 있으며 본 연구실에서 이에 대하여 연구한 결과를 소개하고자 한다. diethylamino titanium을 전구체로 사용하여 $H_2,\;N_2,\;Ar$분위기하에서 pulsed d.c.를 사용하는 MO-PACVD에 의하여 $150~250^{\circ}C$의 저온에서 Al 2024 기판에 TiCN층 형 성을 하였다. 전구체 증발온도는 $74~78^{\circ}C$의 온도범위어야 하며 고경도의 코탱층은 54% duty, 14.2kHz, 450V의 조건에서 얻어졌으며 duty, 주파수, 전압이 증가함에 따라 경도는 저하되었다. 이때의 표면 morphology를 SEM으로 조사한바 dome structure가 크게 발달되었음을 알 수 있었다. 본 실험의 온도 범위내에서 얻은 TiCN 증착반응의 활성화에너지는 7.5Kcal/mol이었다. 증착된 TiCN층은 우수한 내마모섣을 나타내었으며 스크래치테스트 결과 17N의 엄계하중을 나타내었다. 본 연구에서 변화 시킨 duty, 주파수, 전압의 범위에서는 층의 밀착력은 크게 변화하지 않았다. titanium isopropoxide를 전구체로 사용하여 Hz, Nz 분위기하에서 d.c.를 사용하는 MO-PACVD에 의하여 Ti(NCO) 코팅층을 SKDll, SKD61, SKH9 공구강에 형성시키는 공정을 개발하였다. 최적의 Ti(NCO) 코탱층을 얻기 위해 유입전구체 부피%의 양은 향착압력의 5%를 넘지 않아야 되고 수소와 젤소 가스비가 1:1일 때 가장 높은 코팅층의 경도값을 나타내었다. 수소와 질소 가스비가 3:7일 때 TiFeCr(NCO)의 복화합물 코팅층이 형성됨을 알 수 있었고 500t의 증착온도에서 얻은 Ti(NCO) 코팅층이 높은 경도값과 좋은 내식성을 나타내었다. 또한 이와같은 Ti(NCO) 코팅공정과 본 실험실에서 개발한 확산층만 형성시키는 plsma nitriding 공정을 결합하여 복합코탱층을 형성하였는데 이 복합코팅층은 고경도와 우수한 내마모성, 내식성 뿐만 아니라 10)N 이상의 뛰어난 밀착력을 나타내었다. 현재 많이 사용되고 있는 PVD법은 step coverage가 좋지 않은 점과 cost intensive p process라는 단점이 있다. MO-PACVD법은 이러한 문제를 해결할 수 있는 방법으로서 앞으로 지속적인 도전이 요구되는 분야이다.
Modern solid-state gyroscopes (HRG) with hemispherical resonators from high-purity quartz glass and special surface superfinishing and ultrathin gold coating become the best instruments for precise-grade inertial reference units (IRU) targeting long-term space missions. Designing of these sensors could be a notable contribution into development of Korea as a space nation. In participial, 40mm diameter thin-shell resonator from high-purity fused quartz, fabricated as a single-piece with its supporting stem has been designed, machined, etched, tuned, tested, and delivered by STM Co. (ATS of Ukraine) several years ago; an extremely-high Q-factor (upto 10~20 millions) has been shown. Understanding of the best way how to match such a unique sensor with inner glass assembly of the gyro means how to use the high potential in a maximal extent; and this has become the urgent task. Inner quartz glass assembly has a very thin indium (In) layer soldered the resonator and its silica base (case), but effects of internal resonances between operational modal pair of the shell-cup and its side (parasitic) modes can notable degrade the potential of the sensor as a whole, instead of so low level of resonator's intrinsic losses. Unfortunately, there are special combinations of dimensions of the parts (so-called, "resonant sizes"), when intensive losses of energy occurs. The authors proposed to use the length of stem's fixture as an additional design parameter to avoid such cases. So-called, a cyclic scheme of finite element method (FEM) and ANSYS software were employed to estimate different combinations of gyro assembly parameters. This variant has no mismatches of numerical origin due to FEM's discrete mesh. The optimum length and dangerous "resonant lengths" have been found. The special attention has been paid to analyses of 3D effects in a cup-stem transient zone, including determination of a difference between the positions of geometrical Pole of the resonant hemisphere and of its "dynamical Pole", i.e., its real zone of oscillation node. Boundary effects between the shell (cup) and 3D short "beams" (inner and outer stems) have been ranged. The results of the numerical experiments have been compared with the classic model of a quasi-hemispherical shell band with inextensional midsurface, and the solution using Rayleigh's functions of the $1^{st}$ and $2^{nd}$ kinds. To guarantee the truth of the recommended sizes to a designer of the real device, the analytical and FEM results have been compared with experimental data for a party of real resonators. The consistency of the results obtained by different means has been shown with errors less than 5%. The results notably differ from the data published earlier by different researchers.
뿜칠 방수 멤브레인이 가진 높은 부착력과 연성 특성으로 인해 터널 구조물의 보수 보강 목적으로 멤브레인을 적용하는 방안이 고려되고 있다. 따라서 본 연구에서는 인장강도와 부착강도가 향상된 분말 1성분 멤브레인 시제품을 제작하였고, 이를 실물 세그먼트의 내측에 타설하여 실물 실험체를 제작하고 실물 재하실험을 통해 멤브레인의 보강효과를 파악하고자 하였다. 실험결과, 멤브레인의 코팅으로 인해 세그먼트의 균열 발생이 지연되어 세그먼트의 초기 균열발생하중이 평균적으로 약 34% 증가하였다. 반면, 멤브레인 코팅에 의한 파괴하중의 증가율은 상대적으로 크지 않았다. 단, 멤브레인의 코팅으로 인해 파괴 하중 이후에 변형률 연화 현상이 관찰되어, 멤브레인으로 라이닝 내측을 코팅하게 될 경우에는 라이닝의 취성 파괴를 방지하는데 효과가 있을 것으로 추정된다.
폴리디메틸실록산(PDMS)은 화학적 증기 증착 방법을 통해 다양한 물질에 5 nm 두께 이하의 박막 형태로 증착될 수 있다. $SiO_2$, $TiO_2$, ZnO, C, Ni 및 NiO와 같은 다양한 종류의 나노입자 표면에도 PDMS 박막은 증기 증착을 통해 고르게 형성될 수 있으며, PDMS가 증착된 표면은 완벽한 소수성을 갖게 된다. 이 소수성 박막은 안정성이 높아 산, 염기 및 자외선 노출 시에도 잘 분해되지 않으며, 또한 PDMS로 코팅된 나노입자는 다양한 환경 분야에 응용될 수 있다. PDMS 코팅된 소수성 $SiO_2$ 입자는 기름/물 혼합액에서 기름과 선택적으로 반응하고, 기름 유출 사고 시 유류 확산을 억제할 수 있으며, 유출된 기름을 물에서 물리적으로 쉽게 분리할 수 있게 해준다. PDMS 코팅된 $TiO_2$를 진공 상태에서 열처리 할 경우 $TiO_2$ 표면은 완전하게 친수성으로 개질되며, 이때 $TiO_2$가 가시광선을 흡수하여 반응할 수 있게 하는 산소 빈자리 또한 발생하게 된다. PDMS 코팅 후 열처리한 $TiO_2$는 아무 처리하지 않은 $TiO_2$에 비해 가시광 하에서 수중의 유기 염료를 분해하는데 더 뛰어난 광촉매 활성을 보인다. 우리는 해당 연구에서 제시하는 간단한 PDMS 박막 코팅 방법이 다양한 환경 과학 및 공학 분야에서 응용될 수 있음을 소개하고자 한다.
난연 의류는 화염 및 고온 환경 속에서 착용자의 원활한 임무 수행을 돕고 추가적인 피해 확산을 방지한다. 그러나 기존 난연 의류의 높은 중량과 열 피로도는 개선이 필요하며, 친환경적인 방법으로 제작된 가볍고 편리한 난연 의류 개발이 요구되고 있다. 최근 인을 함유한 난연 물질 코팅으로 섬유에 난연성을 부여한 사례가 보고되고 있으나 이들은 국내외 방화복 및 난연 전투복 기준에 적합한 수준으로 발전될 필요성이 있다. 본 연구에서는 깊은 용융 용매로 기능성화된 산화 그래핀과 폴리인산암모늄을 동시에 섬유에 코팅하는 친환경적인 대량생산 공정을 제시한다. 코팅된 섬유는 열무게 분석(Thermogravimetric analysis), 수직불꽃저항성 시험(ASTM D6413), 콘칼로리미터법(ISO 5660-1), 한계 불꽃 확신 속도 시험(ISO 15025)으로 열 안정성 및 난연성이 시험되었다. 기능성화 산화그래핀과 폴리인산암모늄이 동시에 코팅된 직물은 단일 물질 코팅 직물보다 우수한 난연성을 보였고, 연소 이후에도 탄화된 부분의 팽창 효과로 섬유의 형상을 유지하는 것이 관찰되었다. 난연 직물의 세탁 안정성을 위해 추가적인 발수 처리 또한 시도되었다.
Poly propylene carbonate (PPC)와 cloisite 20B (PPC/C-20B)을 solution method를 통하여 합성하였고, 이를 통해 합성된 나노 조성물의 morphology, 열적 특성, 수분 흡수의 특성을 평가하였다. 나노 조성물의 구조는 X-ray diffraction (XRD) 로 확인하였고, 열적 특성은 thermal gravimetric analysis (TGA)와 differential scanning calorimetric (DSC)를 이용해 분석하였다. TGA와 DSC의 결과를 통해 나노 조성물은 기존의 PPC에 비해 높은 열적 안정성을 가짐을 확인할 수 있었다. DSC측정에서 5 wt%의 clay를 포함한 nanohybrid의 유리전이온도는 순수한 PPC의 $21^{\circ}C$에서 $30^{\circ}C$로 $9^{\circ}C$ 증가하였고, TGA 측정을 통해 확인한 열분해온도($T_{d50%}$)는 순수 PPC에 비해 $23^{\circ}C$가 높아졌음을 확인하였다. 또한 PPC 나노 조성물의 수분 흡수량은 기존의 PPC에 비해 상당히 감소하였다. 이는 clay의 PPC matrix 구조 내에 존재함으로 인해 수분 흡수를 감소시킨 것으로 해석할 수 있다. 수분 흡수는 코팅 막의 분해를 유발하고 물리적, 기계적 성능에 영향을 미친다. 따라서 나노 조성물로 인한 PPC의 열적 안정성, 수분흡수도 향상은 PPC의 사용과 실제 공정에 중요한 변수로 작용할 수 있다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.