• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.114-120
• /
• 2000

Friction forces of piston rings for a typical SI engine were independently measured while excluding the effects of cylinder pressure, oil starvation and piston secondary motion using a floating liner system. Friction patterns, represented by the measured friction forces, were classified into five frictional modes with regard to the combination of predominant lubrication regimes(boundary, mixed and hydrodynamic lubrication) and stroke regions(mid-stroke and dead centers). The modes were identified on the Stribeck diagram of the dimensionless bearing parameter and friction coefficients which were evaluated at the mid-stroke and at the dead centers. And the frictional modes were estimated to the full operation range. The compression rings behave in the mode where hydrodynamic lubrication is dominant at the mid-stroke and mixed lubrication is dominant at the dead centers under steady operating conditions. However, the oil control ring behave in the mode where mixed lubrication is dominant throughout the entire stroke.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.6 no.1
• /
• pp.25-31
• /
• 2009

This study presents an analytical model of hydraulic clutch system of a power shift transmission to analyze pressure modulation characteristics. A typical hydraulic clutch system was modeled by using AMESim in which the parameters of major components were measured for simulation. Test apparatus was established using the components of power shift and power shuttle clutches with instrumental equipment. The results of simulation and experiment were so close that the proposed analytical model in this study was validated. However the cylinder model analogized clutch dynamics need to be improved in future study. The effects of parameters of orifice diameter, accumulator stroke and oil temperature on pressure modulation were analyzed respectively. The results of parameter sensitivity analysis show that modulation time and set pressure can be easily adjusted by changing parameter values. It is also found that the hydraulic clutch system used in this study is so susceptible to oil temperature that cooling equipment is necessary.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2916-2921
• /
• 2008

This paper presents the performance and characteristics of small spark-ignited small 2-stroke engine. A single cylinder, two-stroke, air cooled 23cc SI engine for brush-cutter was used in this study. For the performance of the engine, rpm, torque, fuel consumption and lubricate oil consumption were measured, and also HC, CO, NOx emissions and excess air ratio according to throat open ratio under two lubrication method were measured and analyzed. The results showed that maximum of engine rpm is nearly same in both methods and also, torque, power is similar. exhaust emissions tend to decrease with throat open ratio.

• Journal of Drive and Control
• /
• v.14 no.4
• /
• pp.17-22
• /
• 2017

In this study, the back-drivability of the single-rod and double-rod type EHAs (Electro-Hydrostatic Actuators) was compared by computer simulation and experiments. The back-drivability of EHAs exhibit non-linear behavior like their force tracking performance. In case of the double-rod type EHA, the back-drivability was mostly influenced by the bulk modulus of oil that changes with the working pressure due to entrapped air. The back-drivability of the single-rod type EHA was directly affected by the operation states of its pilot-operated check valves, while the asymmetrical piston geometry and the non-linear bulk modulus of oil also made the dynamic response in building up the cylinder pressure dependent on the operating conditions.

• Journal of Drive and Control
• /
• v.18 no.2
• /
• pp.32-37
• /
• 2021

The piston reservoir is mainly used in hydraulic blow-down system for aerospace engineering. The reservoir is heavy due to both hydraulic cylinder and piston in pressurization. The positive expulsion tank with rubber diaphragm has been mostly applied propellant and fuel tank at low pressure to satellites. To reduce weight, the reservoir that can be used at high pressure with rubber diaphragm was developed. In this research, the prediction of life-time for the rubber diaphragm was implemented through an accelerated life test, as a part of development of new reservoir. Also, the diaphragm was stored in an temperature chamber at the same condition as and operation with hydraulic oil. As a result, the life-time for a rubber diaphragm was successfully evaluated via Arrhenius law and Time-Temperature Superposition based on failure times over temperatures in the accelerated test.

• Advances in nano research
• /
• v.15 no.4
• /
• pp.305-313
• /
• 2023

This study is aimed to investigate the electrically conductive properties of epoxy nanocomposites exposed to an acidic environment under various mechanical loads. For simultaneous assessment of the acidic environment and mechanical load on the electrical conductivity of the samples, the samples with and without carbon nanotubes were exposed to the acidic environment under three different loading conditions for 20 days. Then, the aged samples' strength and flexural stiffness degradation under crude oil and bending stress were measured using a three-point flexural test. The aged samples in the acidic environment and under 80 percent of their intact ultimate strength revealed a 9% and 26% reduction of their electrical conductivity for samples with and without CNTs, respectively. The presence of nanoparticles declined flexural stiffness by about 16.39%. Scanning electron microscopy (SEM) images of the specimen were used to evaluate the dispersion quality of CNTs. The results of this study can be exploited in constructing conductive composite electrodes to be used in petroleum environments such as crude oil electrostatic tanks.

• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.4
• /
• pp.18-25
• /
• 1991

디젤엔진에서 윤활오일의 소모량이 점진적으로 증가하는 것은 비정상적인 시린더 마모 때문이다. 시린더 라이너의 작동기구를 L-link 피스톤운동 측정장치로 조사하여 피스톤 top-land의 탄소분 축적이 비정상시린더 마모의 주요 원인임이 증명되었다. 또 피스톤 top-land의 축소는 마모 방지의 유용한 방법인 것으로 이론과 실제에서 입증되었다. 오일 소모와 시린더 마모에 영향을 미치는 다른 요소들에 관해서도 살펴보았다.

• Tribology and Lubricants
• /
• v.11 no.1
• /
• pp.44-49
• /
• 1995

Friction characteristic of an engine crankshaft bearing is affected by revolution speed, applied loads, and viscosity of lubrication. So, experimental investigation is required to observe the friction characteristics using these factors. Hydraulic cylinder, servo controller system which can be modified the applied load, and test rig for the observation of the characteristics of engine crankshaft bearings were designed and fabricated, and some experiments were performed. Friction torque, journal locus and circumferential temperature variation of crankshaft bearing were measured according to applied load, revolution speed, and oil inlet temperature.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1992.04a
• /
• pp.335-340
• /
• 1992

유압 시스템(System)은 원동기의 기계적 에너지를 유압펌프가 작동유를 압력 에너지의 형태로변환 시켜 이것을 유합 실린더(Cylinder)등의 엑츄에이터(Actuator)가 다시 기계적 에너지로 변환시켜 부하 를 구동하게한다. 상용차(NT-1, KH 등)용 파워스티어링(Power Steering)에 장착되는 Vane Type Oil Pump (이하 VOP)가 바로 이와같은 역할을 담당하고 있다. 본 연구에서는 VOP의 성능과 관련되어지는 주요 제원(Parameter)인 미끄럼부에서의 틈새, 작동유점도, 압력변화, 회전수 등을 다양하게 변화시키는 모의실험(Simulation)을 통하여각각의 조건하에서얻어지는 누설 유량과 체적효율을 수치적 으로 예측하고 이것을 주요제원을 고려하여 해석해서 정량적인 값을 얻는 것을 목적으로한다.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1993.12a
• /
• pp.57-62
• /
• 1993

To increase the fuel economy, a reduction of friction loss is important in engines. Experimental investigations have been required for reducing the friction loss of crankshaft bearings. Hydraulic cylinder, and servo control ler system which modified the applied load, and test rig for the observation of the characteristics of engine crankshaft bearings were designed and fabricated. Experiment is performed. Friction torque, journal locus and circumferential temperature variations of crankshaft bearings were measured with appling load, revolution speed, and oil inlet temperature, etc.