• 대한기계학회논문집A
• /
• 제39권12호
• /
• pp.1265-1273
• /
• 2015

석탄하역기는 화력발전소의 주 원료인 석탄을 체인 버킷을 구동하여 선박으로부터 컨베이어 벨트로 하역하는 장비이다. 그러나 국내에서는 석탄하역기의 하역위치에 따라 붐 각도를 제어하는 유압시스템인 붐 호이스팅 실린더에 대한 연구가 이루어지지 않아, 전량 수입하고 있는 실정이다. 이에 본 연구에서는 두꺼운 실린더에서 접촉면압의 이론 값을 FEM 을 수행하여 얻은 결과 값과 비교하여 접촉면압 해석기법의 타당성을 확립하였고, 이를 통하여 브이 실을 갖는 붐 호이스팅 실린더에서 작동유의 누설 여부 판단과 접촉면압을 최대로 갖는 브이 실 형상을 설계하였다. 또한, 실린더의 스트로크에 따른 구동시뮬레이션을 수행하였고, 최대 출력 상태에서의 붐 호이스팅 실런더의 구조 안전성을 검증하였다.

• 동력기계공학회지
• /
• 제13권2호
• /
• pp.5-10
• /
• 2009

In recently, studies concerned to the diesel engine uses a natural gas as a fuel oil whose infra has been built already was approached to PCCI or HCCI with keeping a high thermal efficiency and reducing NOx and PM have been researching actively in normally single cylinder. An ignition source is required to bum the natural gas by a spark plug in gasoline engines, due to a higher auto-ignition temperature of natural gas. Then gas oil and DME were introduced as the ignition source. In this study as basic data for practical use of natural gas PCCI and HCCI engines, combustion characteristics and emission characteristics on 4-cylinders natural gas PCCI and HCCI engines with gas oil and DME as ignition sources were analyzed and the engine load range that is main object for practical use of PCCI and HCCI engines was made clearly by empirical experiment.

• 한국안전학회지
• /
• 제2권1호
• /
• pp.59-71
• /
• 1987

A study has been made of the damping force phenomena of the shockabsorber for automobile. The main results obtained are as follows; 1) We can neglect friction loss between cylinder and piston, as it is very small compared to other damping force. 2) Damping force due to coil spring and disc valve shows comparatively stable at various piston speed and oil temperature. 3) Theoretical and experimental values are well agreed on relatively low piston speed. 4) Theoretical value on piston speed of 600mm/sec, 900mm/sec at oil temperature $20^{\circ}C$, $40^{\circ}C$, $60^{\circ}C$ and $80^{\circ}C$ is about 82% of experimental value. 5) Theretical value at oil temperature $-20^{\circ}C$, $0^{\circ}C$ is about 67% of experimental value.

• 대한기계학회논문집
• /
• 제18권6호
• /
• pp.1510-1519
• /
• 1994

It is important to understand the friction characteristics between piston-ring assembly and cylinder wall for the friction loss reduction as well as the solution of problem such as scuffing wear and oil consumption. A new system was developed for the piston-ring assembly friction force measurement. This system was applied to the friction force measurement to find its functional relationship with variables such as engine speed, oil viscosity, and engine load. The friction mean effective pressure(fmep) was found to have a linear relationship with$(\vpsilon{U})^{0.42}$ under motering and with$(\vpsilon{U})^{0.45}$ under firing operations, where $\vpsilon$ is the kinematic oil viscosity and U is mean piston speed.

• 한국정밀공학회지
• /
• 제14권11호
• /
• pp.11-16
• /
• 1997

In the stroke sensitive shock absorber, the oil path is formed along the internal cylinder surface to make the oil flow during the piston's upper-lower reciprocation movement. In constrast with the conventional shock absorbesr which show one dynamic characteristic curve, stroke sensitive shock absorber shows two kinds of dynamic characteristics according to the stroke. In this study, in order to obtain more precise information about design and damping performance analysis, the analysis on the damping force generation process and dynamic behaviour characteristics of stroke sensitive shock absorber are performed by considering the valve characteristics.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1993년도 춘계학술대회 및 공장견학
• /
• pp.39-53
• /
• 1993

The minimum oil film thickness(MOFT) in the connecting-rod bering of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film charactrtistics. And cylinder pressure, crank-pin surface temperature and bearing tenp ture are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable detmuuination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• 한국기계가공학회지
• /
• 제19권8호
• /
• pp.110-116
• /
• 2020

Aircraft hydraulic oil reservoirs made with aluminum 7075 have an anodized coating to enable airtightness and corrosion resistance. To maintain a stable oil pressure, the internal surface roughness of the reservoir should be less than approximately 0.2 ㎛. To this end, precision polishing must be performed. However, ensuring the processing quality is challenging, as most polishing operations are performed manually, owing to which, the inner surface roughness is not uniform, and the product quality is irregular. Therefore, we developed a special superfinishing machine to realize the efficient inner polishing of an aircraft hydraulic oil reservoir, by using an abrasive film to improve the process throughput and uniformity. In the experiment involving the superfinishing of an anodized aluminum 7075 cylinder specimen by using the proposed machine, a higher surface roughness than that achieved in the repetitive manual polishing process could be realized.

• Journal of Advanced Marine Engineering and Technology
• /
• 제30권6호
• /
• pp.662-668
• /
• 2006

The effects of fuel injection nozzle hole on the NOx emission and fuel oil consumption of medium speed diesel engine HYUNDAI HiMSEN 6H21/32 engine are investigated by engine performance simulation. The results of performance simulation are verified by experimental results of NOx omission fuel oil consumption, cylinder pressure, and heat release rate according to the variation of the number of fuel injection nozzle hole and engine load. The performance simulations are also carried out to optimize the fuel injection nozzle of 6H21/32 engine in respect to the NOx emission and fuel oil consumption. The engine performance measurements are performed to verify the results of performance simulation and to investigate the effects of fuel injection nozzle on engine performance. The results of measurement indicate that significant NOx reduction can be achieved with minimum deterioration in fuel oil consumption by optimizing the geometry of fuel injection nozzle on 6H21/32 engine.

• Tribology and Lubricants
• /
• 제10권1호
• /
• pp.14-26
• /
• 1994

The minimum oil film thickness(MOFT) in the connecting-rod bearing of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film characteristics. And cylinder pressure, crank-pin surface temperature and bearing temperature are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable determination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• 한국분무공학회지
• /
• 제25권4호
• /
• pp.162-169
• /
• 2020

The worldwide focus on reducing the emissions, fuel and lubricant consumption in T-GDI engines is leading engineers to consider the crankcase ventilation and oil mist separation system as an important means of control. In today's passenger cars, the oil mist separation systems mainly use the inertia effect (e.g. labyrinth, cyclone etc.). Therefore, this study has investigated high efficiency cylinder head-integrated oil-mist separator by using a compact multi-impactor type oil mist separator system to ensure adequate oil mist separation performance. For this purpose, engine dynamometer testing with oil particle efficiency measurement equipment and 3D two-phase flow simulation have been performed for various engine operating conditions. Tests with an actual engine on a dynamometer showed oil aerosol particle size distributions varied depending on operating conditions. For instance, high rpm and load increases bot only blow-by gases but the amount of small size oil droplets. Submicron-sized particles (less than 0.5 ㎛) were also observed. It is also found that the impactor type separator is able to separate nearly no droplets of diameter lower than 3 ㎛. CFD results showed that the complex aerodynamics processes that lead to strong impingement and break-up can strip out large droplets and generate more small size droplets.