• 한국자동차공학회논문집
• /
• 제11권1호
• /
• pp.32-41
• /
• 2003

For the countermeasure of expected higher thermal load in miller cycle engine, coolant flows in the cylinder head of base engine with several coolant flow methods and drilled hole passages were measured by using PIV technique. And the cooling effect was evaluated by measurements of wall temperatures according to each coolant flow method. It was found that the series flow system was most suitable among the discussed 3 types of coolant flow methods since it had the best cooling effect in cylinder head by the fastest coolant flow velocity It was also found that for drilled water passage to decrease the large thermal load in exhaust valve bridge, nozzle type is more effective compared with round type of water passage, and its size has to be determined according to the coolant flow pattern and velocity in each cylinder.

• 한국자동차공학회논문집
• /
• 제5권2호
• /
• pp.183-196
• /
• 1997

Gas flow field within the cylinder which is called a tumble flow is important factor in improving lean combustion stability. In this study, steady state flow tests were performed to quantify tumble ratio of flowfields generated by a tumble intensifying valve(TIV). In addition, velocity and fluctuation profiles in an intake port and flowfields in th cylinder were inspected using a hotwire anemometer and a laser light sheet method with various TIV configurations. These experimental results show that installated TIV has a great effect on flow field distribution in an intake port and test effects enhance a tumble flow in the cylinder.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.421-422
• /
• 2002

The purpose of this paper is to investigate the leakage characteristics of the valve stem in the gasoline engines. Especially, three factors affecting oil leakage are the power cylinder, engine head system, and the positive crankcase ventilation system. Which is the most variables, analysis difficulty is the valve stem seal characteristics. The testing system is used with oil motoring system. The leakage of an engine is analyzed for the cylinder temperature, atmosphere pressure, positive pressure, negative pressure, revolution of the camshaft and the surface roughness of the valve stem.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.140-147
• /
• 2001

The solenoid valve in ABS hydraulics, modulator is a two directional on-off valve and is controlled by around 100Hz high speed pulse width modulation. When the inlet valve is switched from open state to closed state, there are braking force degration, noise and vibration due to pressure surge phenomena in the hydraulic line and wheel cylinder. In this study, identifies pressure surge phenomenon in the braking process of a ABS, and investigates the way to reduce the phenomenon. For the purpose theoretical analysis on the pressure surge in the closed state hydraulic line, characteristic curve method based on wave equation was utilized. During this analysis, we could find pressure surge characteristics change due to hydraulic line change and PWM control conditions. In conclusion, by using the results of this study for the pressure surge prediction and reduction method, we could expect braking performance enhancement in Anti-Lock Braking System.

• 한국자동차공학회논문집
• /
• 제1권1호
• /
• pp.1-13
• /
• 1993

The three-dimensional numerical analysis for in-cylinder flow of four-valve engine without intake port has been successfully computed. These computations have been performed using technique of the general coordinate transformation based on the finite-volume method and body-fitted non-orthogenal grids using staggered control volume and covariant variable as dependent one. Computations are started at intake valve opening and are carried through top-dead-center of compression. A k-$\varepsilon$model is used to represent turbulent transport of momentum. The principal study is the evolution of interaction between mean flow and turbulence and of the role of swirl and tumble in generating near TDC turbulence. Results for three different inlet flow configuration are presented. From these results, complex flow pattern may be effective for promoting combustion in spark-ignition engines and kinetic energy of mean flow near TDC is well converted into turbulent kinetic energy.

• Journal of Advanced Marine Engineering and Technology
• /
• 제22권1호
• /
• pp.42-51
• /
• 1998

A 150 m$\^$3//hr, 30 kg/cm$\^$2/, air-cooled 3-stage reciprocating air compressor is designed to be used in starting large diesel engines of ships. A basic design procedure is presented to meet the targeted pressure and flow rate, and especially a volumetric efficiency of 80%. Temperature and stress analysis of the 1st stage cylinder are performed using axisymmetric FEM modelings. The dynamics of valve system is analyzed and stress at the 1st stage valve seat caused by valve impact is evaluated. To reduce friction loss and wear at the compressor engine system tribological design issues are reviewed and good design practices are suggested. Finally, forced-air pin-type interstage coolers are designed to dissipate generated compression heat at each stage.

• 오토저널
• /
• 제8권2호
• /
• pp.65-74
• /
• 1986

A computer program was developed to predict swirling steady axisymmetric turbulent flows by extending TEACH Code. It was applied to a reciprocating engine cylinder with a intake valve on the flat head. Flows were assumed to be steady and swirling. Effects of Reynolds number, the valve lift, and the swirl ratio on flow patterns and turbulence were investigated numerically. Flow patterns were reasonably predicted in comparison with experimental results. Length of the recirculation zone was shortened with increasing valve lifts and swirl ratios. Static pressure distributions show maximum value near the reattachment point of the incoming circular jet and minimum value near the maximum width of the valve attached recirculation zone.

• 연구논문집
• /
• 통권23호
• /
• pp.63-71
• /
• 1993

To improve flow in-cylinder flow in a 2-valve gasoline engine, various geometries of combustion chambers are modified. Air flow rate, swirl and tumble flow are measured and analyzed by swirl impulse meter and LDV in a steady state flow measuring rig. The results of LDV experiment are compared with the data of swirl impulse meter.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.826-830
• /
• 1996

The pneumaic systems are widely applied to chemical factory of fire dangry and factory automation. by using compressed air, it is difficult to dynamics action analysis that the pneumatics system acts to nonlinear motion through orifices and valve flow. This paper was studied to a nonlinear chararistics of pneumaic spring, damper and absorber of pneumaic cushion cylinder.

• ALGAE
• /
• 제22권4호
• /
• pp.253-259
• /
• 2007

This study deals with the taxonomy of the marine diatom Ditylum brightwellii (West) Grunow: shape, size and ratio, marginal ridge, labiate process, areolation, and seasonal distribution are all considered. Ditylum brightwellii were divided into two type; prism- and cylinder-shaped. Comparisons between specimens from the Yellow Sea were made on, (1) shape- prism types are prismatic-shaped and/or regular square or right-angled tetragon, cylinder types are cylinder-shaped and/or long right-angled tetragon in the girdle view, respectively; (2) size and ratiodiameters of prism types are 82.1 ± 2 μm, while those of cylinder types are 21.2 ± 5 μm and ratio of pervalvar axis/diameter- prism types cells are 1.0-1.5, but cylinder types are 3.9-5.5; (3) marginal ridges- prism types have dotted, while those of the cylinder-type cells have piece, slotted or fimbriated on the marginal ridge; (4) labiate process- both prism- and cylinder-types are central part in valve face, but length of labiate processes of prism types are longer than those of cylinder types; (5) cell margin- the girdle margin show many shallow furrows in prism type and smooth in cylinder type; (6) areolation- both prism- and cylinder-types are a radial pattern in the valve center, but areolae of prism types are larger than those of cylinder types; (7) seasonal distribution- cylinder types are dominated in summer and prism types in the other seasons.