• 한국안전학회지
• /
• 제4권1호
• /
• pp.25-39
• /
• 1989

Cyclic temperature creep tests were carried out an AS 7075 alloy specimens were subjected to a constant load and stepwise temperature cycles in which temperature was fluctuated between 30$0^{\circ}C$ and 25$0^{\circ}C$ with three different cycle ratios. The highest frequency of cycling was 1 cycle per 10 hr and the lowest one was 1 cycle per 12 hr. From the creep experimental results with the above conditions the creep strain under cyclic temperature can be predicted easily by introd ucing the equivalent steady temperature because defined by Eq.(16), but the rupture life is 1.1 time than those of constant temperature because of effect of temperature history at tertiary creep range. Besides thlis result, the results of the creep test under cyclic temperature conditions are respectively compayiea with calculated rupture lives using the life fraction law and Eq.(18). The agreement between the obseried rupture times and calculated ones is fairly good. So creep rupture lives can be respectively predicted using life fraction law and Eq.(18).

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제6권12호
• /
• pp.3046-3060
• /
• 2012

Low power listening (LPL) MAC protocols based on duty-cycling mechanism have been studied extensively to achieve ultra low energy consumption in wireless sensor networks (WSNs). Especially, recent ACK-based LPL schemes such as X-MAC employ strobe preambles and an early ACK, and show fair performances in communications and energy efficiencies. However, the state-of-the-art ACK-based LPL scheme still suffers from collision problems due to the protocol incompleteness. These collision effects are not trivial and make WSNs unstable, aggravate energy consumptions. In this paper, we propose two novel schemes; (i) ${\tau}$-duration CCA to mitigate the collision problem in ACK-based LPL MAC protocols. (ii) Short Preamble Counter (SPC) to conserve more energy by reducing unnecessary overhearing. We demonstrate the performance improvement of our scheme via a mathematical analysis and real-time experiments. Both analysis and experimental results confirm that our proposed scheme saves energy by up to 36% compared to the naive ACK-based LPL MAC protocol thanks to ${\tau}$-duration CCA and SPC.

• 한국표면공학회지
• /
• 제32권1호
• /
• pp.49-60
• /
• 1999

The protective oxide scales and coatings formed on high temperature materials must be preserved in high temperature atmosphere. And the thermal stresses induced by thermal cycling and the growth stresses by the formation of oxide scales can cause the loss of adherence and spalling of the oxide scales and coated layers. Among the coating processes Al diffusion coating is favored due to thermochemical stability and superior adherence in an hostile atmosphere. In this study, protective oxide forming element, Al was coated on Ni, Inconel 600 and 690 by diffusion coating process varying coating temperature and time. And the surface stability and adherence of oxide scales formed on those Al diffusion coated materials were evaluated by thermal cycling test. Al diffusion coated specimens showed superior cyclic oxidation resistance compared to bare ones and specimens coated for longer period had better cyclic oxidation resistance, due to the abundant amount of Al in the coated layer. Meanwhile Al diffusion coated Inconel 600 and 690 showed improved cyclic oxidation resistance by the effect of Al in the coated layer and Cr in the substrate. Comparing both Al diffusion coated Inconel 600 and 690, Al diffusion coated Inconel 690 maintained better adhesion between coated layer and substrate by virtue of the bridging effect resulting from the segregation of Cr in the interdiffusion zone.

• 소성∙가공
• /
• 제33권5호
• /
• pp.330-340
• /
• 2024

The martensitic Ni-Ti shape memory alloys(SMA) can achieve a two-way shape memory effect (TWSME) through thermomechanical training/cycling. In this study, the surface of Ni-Ti SMA sheets was treated by depositing a certain number of titanium (Ti) powder layers using a selective laser meling (SLM) process to enhance TWSME. The results showed that a unique TWSME of approximately 12% with good stability was achieved after 100 training cycles when the optimum number of five Ti layers was deposited. A larger HAZ and lower cooling rate pushed more Ti particles into the grains rather than the grain boundaries, providing more time for Ti to react with NiTi to form Ti-rich intergranular Ti2Ni(Ox) precipitates. This resulted in further hindering of dislocation movement within the grains and the generation of internal stress fields required for attaining a larger TWSME. With an increase in the number of Ti-deposited layers, there was no noticeable reduction in the one-way shape memory effect (OWSME) through the initial cycling. This was due to the high residual tensile stress caused by the lower thermal expansion of the Ti layer compared to the Ni-Ti sheet.

• 대한의용생체공학회:의공학회지
• /
• 제17권3호
• /
• pp.313-318
• /
• 1996

We proposed a new system for the postural balance rehabilitation training. For the purpose, we used the virtual hiking system using virtual reality technology. We evaluated the system by measuring the parameters such as path deviation, path deviation velocity, cycling time, and head movement. From our results, we verified the usefulness of virtual reality technology in rehabilitation. Our results showed that this system was effective postural balance rehabilitation training device and might be useful as the clinical equipment.

• 한국환경과학회지
• /
• 제20권1호
• /
• pp.49-59
• /
• 2011

The effect of the variation of aeration time on the microorganisms was investigated in sequencing batch reactor (SBRs). The cycling time in four SBRs was adjusted to 12 hours and then included different aerobic times as 1 hr, 2.5 hr, 4 hr and 5.5 hr, respectively. Four SBR systems have been operated and investigated for over 40 days. As the increase of aeration time, the consumption of glycogen within sludge at the 1st non-aeration time a little bit was increased and the production of glycogen at the aeration time was increased. Also, the produced PHB amounts and PHB production rate at the 1st non-aeration time were increased as the decrease of aeration time, which showed the activation of the phosphorus removal. The ratios of nitrifying microorganisms' number and GAOs to the total microorganisms' number in SBRs was decreased as the decrease of the aeration time, however, the PAOs ratio was almost constant irrespective of the variation of aeration time.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.322-322
• /
• 2016

Phase change memory (PCM) has attracted much attention as one of the most promising candidates for next-generation nonvolatile memory. In that regard, the purposes of the study are to propose reference of effective pulse parameter to control phase switching operation and to invest the effect of nitrogen doped in PCM materials for improved cycling stability and economic energy consumption. Switching operation of PCM is affected by electric pulse parameter and as shown in figure.1 are composed to RT(rising time), ST(setting time), FT(falling time) and the effect of these parameter was precisely investigated. Transmission electron microscope (TEM) was used to confirm fine structure and retention cycle test was conducted to confirm reliability. Finally improvement reliability and economic power consumption in quantitatively are obtainable by optimum pulse parameter and nitrogen doping in GST material. these study is related to the engineering background of other semiconductor industries and it have confirmed to possibility further applications.

• 디지털산업정보학회논문지
• /
• 제4권3호
• /
• pp.77-83
• /
• 2008

In this paper, CPLD low power technology mapping for reuse module design under the time constraint is proposed. Traditional high-level synthesis do not allow reuse of complex, realistic datapath component during the task of scheduling. On the other hand, the proposed algorithm is able to approach a productivity of the design the low power to reuse which given a library of user-defined datapath component and to share of resource sharing on the switching activity in a shared resource. Also, we are obtainable the optimal the scheduling result in experimental results of our using chaining and multi-cycling in the scheduling techniques. Low power circuit make using CPLD technology mapping algorithm for selection reuse module by scheduling.

• 한국화재소방학회논문지
• /
• 제15권4호
• /
• pp.41-48
• /
• 2001

할론소화약제는 유류화재 및 전기화재의 진압에 가장 효과적으로 널리 사용되어 왔으나, 이들은 오존층파괴지수와 지구온난화지수가 높아 환경문제를 야기하고 있다. 이러한 환경에 악영향을 주지 않는 대체기술의 하나로 관심을 끌며 연구되기 시작한 소화방법이 미세물분무를 이용한 소화설비이며, 미세물분무는 스프링클러의 살수입자에 비해 물입자가 작고 표면적이 크기 때문에 화염면에서의 증발 및 냉각특성이 우수하며, 산소의 농도를 감소시키는 질식작용이 우수하다. 본 연구는 미세물분무 소화설비의 설계를 위한 기초단계로 유류화재에 대한 미세물분무의 입자크기, 유량밀도, 방사분포, 방사압력 및 화재의 크기에 따른 화염의 소화특성을 측정하였다. 그 결과 액체 poo l화재의 소화시간은 유량밀도가 증가함으로서 짧아지고, 유량밀도가 0.5$\pm$0.05ml/$\textrm{cm}^2$ . min이하인 경우 입자크기가 증가함으로서 짧아졌다. 또 방사주기를 변화시켜 실험한 결과 n-heptane 화재에 대하여 간헐적으로 방사한 미세물분무가 소화에 효과적이었으며, 이때 연속방사와 비교하여 화재를 소화하기 위해 필요한 물의 총량은 1/4로 감소하였다.

• 대한의용생체공학회:의공학회지
• /
• 제28권6호
• /
• pp.832-839
• /
• 2007

In this study, a new bicycle system was developed to improve muscular strength using the Magneto-Rheological(MR) rotary brake. The friction load of the MR rotary brake is adjusted according to muscle strength of the subjects. The characteristic of muscular strength was studied with various friction loads of MR rotary brake. The friction load was occurred with the current, applied to the MR. rotary brake. Experiments was composed of several cycling trials for various friction loads. In training programs involving muscle improvement, it is necessary to confirm muscle activity and fatigue. To measure the muscle activity and fatigue, EMG signals of rectus femoris (RF), biceps femoris (BF), tensor fasciae latae (TFL), vastus lateralis (VL), vastus medialis (VAS), gastrocnemius (GAS), tibialis anterior (TA) and soleus (SOL) muscles were collected with surface electromyography and analyzed into time and frequency domain. The experimental results showed that the muscle activity according to the applied current to the MR rotary brake was significantly different. The more the current was applied, the higher value of the integrated EMG (IEMG) was obtained. Especially, the magnitude of IEMG of the RF, BF, TFL and VL varied in direct proportion to the current. However, there was not significant in the median frequency as the cycling time continue.