• Journal of Hydrogen and New Energy
• /
• v.23 no.2
• /
• pp.173-182
• /
• 2012

Effects of temperature, pressure, and gas residence time on methane combustion characteristics of mass produced oxygen carrier particle (OCN706-1100) were investigated in a pressurized fluidized bed reactor using methane and air as reactants for reduction and oxidation, respectively. The oxygen carrier showed high fuel conversion, high $CO_2$ selectivity, and low CO concentration at reduction condition and very low NO emission at oxidation condition. Moreover OCN706-1100 particle showed good regeneration ability during successive reduction-oxidation cyclic tests up to the 10th cycle. Fuel conversion and $CO_2$ selectivity decreased and CO emission increased as temperature increased. These results can be explained by trend of calculated equilibrium CO concentration. However, $CO_2$ selectivity increased as pressure increased and fuel conversion increased as gas residence time increased.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.12
• /
• pp.1281-1286
• /
• 2015

Fatigue cracks can be generated in aircraft as a result of the cumulative time spent during flight operations, which can extend for long periods of time and cover a variety of missions. If a crack occurs in an aircraft's main spar, it can generate many problems, including a lift time reduction. To solve this problem, it was necessary to perform an analysis of fatigue crack growth in the fatigue critical locations. Much time and expense is involved in generating the stress needed for a crack propagation analysis over a long period of time to obtain the amount of data required for an actual aircraft. In this paper, an algorithm is developed that can calculate the spectrum of stress over a long period of time for a mission by the Southwest Research Institute, which is based on the short-time load factor data produced using the peak-valley cycle counting method.

• Particle and aerosol research
• /
• v.20 no.2
• /
• pp.69-77
• /
• 2024

In this study, the performance of air cleaners installed in subway stations was evaluated using field test method and chamber test method in accordance with the standard for air cleaner. Also, the air filter maintenance period was examined by the performance reduction of air cleaners with respect to the air filter usage period. From the field tests, the clean air delivery rate (CADR) of air cleaners with filter in use was about 85% on average compared to the ones with new filter. The main factor of CADR reduction was not the decrease of filter efficiency but the decrease of airflow rate. The chamber test results shows that the CADR of air cleaners decreased with the usage time, but the proper filter replacement can make the CADR keep about 95% of the certified CADR. The expected filter replacement cycle measured by the field test method was calculated to be approximately 3.35 months (100 days). However, the replacement cycle was a large difference between 1.2 and 6.6 months with the different stations. Therefore, the replacement cycle should be individually investigated for each station. The use of air cleaners must be effective in reducing fine dust in subway stations. For more effective air quality management in subway stations, additional researches is necessary to define the appropriate capacity of HVAC system and air cleaner, and related maintenance for each station.

• Journal of the Korean Solar Energy Society
• /
• v.37 no.5
• /
• pp.27-37
• /
• 2017

In this study, an artificial solar simulator composed of a 2.5 kW Xe-Arc lamp and mirror reflector was used to carry out the solar thermal two step thermochemical water decomposition cycle which can produce high efficiency continuous hydrogen production. Through various operating conditions, the change of hydrogen production due to the possibility of a dual-zone reactor and heat recovery were experimentally analyzed. Based on the reaction temperature of Thermal-Reduction step and Water-Decomposition step at $1,400^{\circ}C$ and $1,000^{\circ}C$ respectively, the hydrogen production decreased by 23.2% under the power off condition, and as a result of experiments using heat recovery technology, the hydrogen production increased by 33.8%. Therefore, when a thermochemical two-step water decomposition cycle is conducted using a dual-zone reactor with heat recovery, it is expected that the cycle can be operated twice over a certain period of time and the hydrogen production amount is increased by at least 53.5% compared to a single reactor.

• Human Ecology Research
• /
• v.53 no.1
• /
• pp.49-66
• /
• 2015

This study analyzes the effects of women's labour force participation and work-family reconciliation support on life-cycle fertility in Korea. The analysis is based on the longitudinal data from Korean Labour and Income Panel Study (KLIPS), which include the available information on life-cycle fertility and employment history. Employing a dynamic model of fertility, we estimated the life-cycle fertility of all the 15-49 years old women considered in this study by using a duration model. The major results of this study were as follows: First, women's labour force participation had a negative effect on the first birth, second birth, and all births (transition to births starting at different parities). Women's employment tended to lengthen the interval between births. Second, the availability of maternal leave had a positive effect on the first birth and all births for working women. Providing maternal leave to working women decreased the opportunity cost of childbearing and in turn, reduced the interbirth interval of women. However, the availability of parental leave had no significant effect on the births of working women. Third, the financial support for childcare had a positive effect on the first birth and all births. The economic support for childcare led to the reduction in the interbirth interval of women by increasing the probability of births. The use of a childcare center for the first child, which substitutes for the time that women needed to take care of their children, classified as time-intensive consumption goods, did not have any effect on the second birth. Fourth, the part-time employment of women had a positive effect on the second birth. A flexible working time schedule tended to decrease the interval between the first and the second births.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.6
• /
• pp.835-842
• /
• 2009

The present thesis carried out a research on a compression pressure's reduction phenomenon and its countermeasure according to the thermal efficiency improvement method by a Miller method in 4-cycle low speed diesel engine. In case of retardation of intake valve closing time in a engine, the theoretical heat efficiency shows a remarkably reducing trend when a compression ratio is not compensated. Accordingly, the thermal efficiency showed an increasing trend in case of compensating the compression ratio. Especially, it could be understood that the theoretical heat efficiency at near ABDC $100^{\circ}$ of intake valve closing time in case of compensation of the compression ratio was improved by around 25.1%, and the mean effective pressure was also increased by around 18.6%. Also, as the retardation of intake valve closing time increases, air quantity becomes insufficient due to a backflow phenomenon of intake air and thus thermal efficiency was decreased in a high load operation domain. The solving method of this problem is possible by supercharge. Therefore, in order to improve thermal efficiency by retardation of ntake valve closing time, the thermal efficiency improvement according to low compression is possible when there are a compensation device of a compression ratio and a supercharge device. This is a problem-solving method of low compression and high expansion cycle.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.373-376
• /
• 2001

In this paper to cope with the reduction of products life-cycle as the variety of products along with the various demands of consumers, a virtual simulator is developed to make the changeover of manufacturing line efficient to embody a virtual simulation similar to a real manufacturing line. The developed virtual simulator can design a layout of a factory and make the time scheduling. Every factory has one simulator so that one product can be manufactured in the factories to use them as virtual factories. We suggest a scheme that heightens the ability to the diversity of manufacturing models by making the information of manufacturing lines and products models to be shared. The developed system embodies a virtual manufacturing line on the simulation using various manipulators and work cells as manufacturing components. we develop a virtual simulator system on Window 98/NT environment of Microsoft, operating system using of the greater part of PC user. Window program have a merit making GUI environment that programmer can use without the expert knowledge about hardware. A suer with the simulator can utilize an interface that makes one to manage the separate task process for each manufacturing module, change operator components and work cells, and easily teach tasks of each task module.

• Journal of architectural history
• /
• v.31 no.1
• /
• pp.41-50
• /
• 2022

Traditional wooden buildings deform over time and are vulnerable to fire or earthquakes. Therefore, traditional wooden buildings require continuous management and repair, and securing architectural drawings is essential for repair and restoration. Unlike modernized CAD drawings, traditional wooden building drawings scan and store hand-drawn drawings, and in this process, many noise is included due to damage to the drawing itself. These drawings are digitized, but their utilization is poor due to noise. Difficulties in systematic management of traditional wooden buildings are increasing. Noise removal by existing algorithms has limited drawings that can be applied according to noise characteristics and the performance is not uniform. This study presents deep artificial neural network based noised reduction for architectural drawings. Front/side elevation drawings, floor plans, detail drawings of Korean wooden treasure buildings were considered. First, the noise properties of the architectural drawings were learned with both a cycle generative model and heuristic image fusion methods. Consequently, a noise reduction network was trained through supervised learning using training sets prepared using the noise models. The proposed method provided effective removal of noise without deteriorating fine lines in the architectural drawings and it showed good performance for various noise types.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.12 no.3
• /
• pp.121-130
• /
• 2017

NAND flash memory has advantages of non-volatility, little power consumption and fast access time. However, it suffers from inability that does not provide to update-in-place and the erase cycle is limited. Moreover, the unit of read/write operation is a page and the unit of erase operation is a block. Therefore, erase operation is slower than other operations. The AGC, the proposed garbage collection policy focuses on not only garbage collection time reduction for real-time guarantee but also wear-leveling for a flash memory lifetime. In order to achieve above goals, we define three garbage collection operating modes: Fast Mode, Smart Mode, and Wear-leveling Mode. The proposed policy decides the garbage collection mode depending on system CPU usage rate. Fast Mode selects the dirtiest block as victim block to minimize the erase operation time. However, Smart Mode selects the victim block by reflecting the invalid page number and block erase count to minimizing the erase operation time and deviation of block erase count. Wear-leveling Mode operates similar to Smart Mode and it makes groups and relocates the pages which has the similar update time. We implemented the proposed policy and measured the performance compare with the existing policies. Simulation results show that the proposed policy performs better than Cost-benefit policy with the 55% reduction in the operation time. Also, it performs better than Greedy policy with the 87% reduction in the deviation of erase count. Most of all, the proposed policy works adaptively according to the CPU usage rate, and guarantees the real-time performance of the system.

• Korean Journal of Food Science and Technology
• /
• v.27 no.6
• /
• pp.991-996
• /
• 1995

Effects of high hydrostatic pressure on microorganisms and browning enzymes in Angelica keiskei juice were investigated using response surface methodology. The optimum process condition for maximum reduction of total aerobes was $5700\;kg_f/cm^2$ (558.6 MPa) pressure and 7.16 min process time, and 3.44 log cycle reduction of total aerobes was predicted at the optimum condition. E. coli, initially $8.8{\times}10^3\;CFU/ml$, was completely inactivated by high hydrostatic pressure at all process conditions ($3800{\sim}6700\;kg_f/cm^2\;pressure;\;3{\sim}17\;min\;process\;time$). Polyphenol oxidase and peroxidase were partly inactivated by the high hydrostatic pressure. It was also indicated that inactivation of microorganisms and browning enzymes by hydrostatic pressure is dependent on pressure rather than process time.