• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.11
• /
• pp.89-95
• /
• 2019

In this research, the effect of roughing on tool load through bottom-up machining is investigated through actual machining. Generally, through the use of high-speed machining technology, machining methods, such as general roughing, operate by deepening the cutting depth for as long as the tool is able to withstand it, giving a slower feed rate, less cutting depth, and faster feed. However, when the cutting depth is deep, there is a problem in that the stepped shape of the cutting area is increased (e.g., by the shaking of the tool or the chipping load). However, if the cutting is performed less, the cutting time becomes relatively long. To compensate for these drawbacks and extend the service life of the tool, economic efficiency needs to be secured.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.11 no.1
• /
• pp.95-101
• /
• 2009

This study was carried out to investigate the optimum condition of germination temperature and cutting condition in Thymus quinquecstaus. A germination rate was superior at light condition and 20℃ in temperature(rooting rates : 89%) Rooting rates by cutting times were the highest in 20th May(rooting rates : 94%) The best Cutting media for rooting rates and member of roots observed peatmoss (50%)+perlite(50%) among the Cutting media. The rooting rates by concentration of growth hormone were the highest(96%) at IBA 100·mg/l among the treatment.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.12
• /
• pp.60-66
• /
• 2004

Increasing demands on precision machining of 3D free-form surface have necessitated the tool to move smoothly with varying feedrate. To this regard, parametric interpolators such as NURBS (Non-Uniform Rational B-Spline) interpolator have been introduced in CNC machining system. Such interpolators reduce the data burden in NC code, increase data transfer rate into NC controller, and finally give smooth motion while machining. In this research, a new concept to control cutting load in NURBS Interpolator was tried based on the curvature of curve. This is to protect cutting tool, and to have good machinability. For proof of the system, cutting force and surface topography were evaluated. From the experimental results. the interpolator is good enough for machining a free-form surface.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.3
• /
• pp.28-34
• /
• 1997

The side burrs and shape distortion resulting from the micromachining of an array of V-shape microgrooves in fresnel lens mould were experimentally invesigated. The focus of this study is on the influence of depth of cut and prism angle on the burr growing rate. The main experiments were con- ducted on the single prism cutting for the convinient of measuring the burr shape and cutting force. From the observation of the burr shape and burr growing rate, it was found that there exits a critical depth of cut below which the burrs are more or less irregular and weak. But above that critical value, the burrs are re- latively clear and stiff.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.102-106
• /
• 1996

In the ball end-milling process of a 3-dimensional mold, it is important to select cutting conditions and tool path considering the geometrical shape of a workpiece to reduce machining time. In this study, experiments were performed to decide allowable feed rate not breaking stability of system for different geometrical shapes. It was found that downcut is more stable than upcutting in machining side wall and downward is preferable to upward in inclined part depending on the angle of the inclination and depth of cut.

• Journal of Power System Engineering
• /
• v.6 no.1
• /
• pp.82-87
• /
• 2002

Not only ferrous but also non-ferrous materials such as aluminum, brass, plastic and woods need cutting operation in recent manufacturing industry. Over the past few years a considerable number of studies have been made on non-ferrous metal cutting. But more study is required to meet various engineering needs. The purpose of this paper is to preform an experiment on the influence of feed-rate adjustment and side rake angle in turning operations from non-ferrous metals. As a result, the surface roughness was reduced when a side-rake angle increases and feed-rate decreases in the case of the plastic, brass, aluminum, and paulownia. Therefore, this papers develop a new type bite that be used to adjust side-rake angle.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.7
• /
• pp.42-47
• /
• 2019

In this research, we try to study the change of squareness in the cutting process while changing cutting conditions such as feed rate and spindle rotational speed with chromium molybdenum steel (SCM415) material and TiCN, TiAlN coated end mill tool. The TiCN coating tool had the best straightness at 4,000 rpm at a feed rate of 200 mm/min. The TiAlN coating tool was best measured at 3,000 rpm at a feed rate of 200 mm/min. TiAlN coated tools had excellent dimensional tolerance when comparing the coating tool specifics.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11c
• /
• pp.578-585
• /
• 2000

Geometrical characteristics of fresh red pepper(Capsicum annuum L.) were measured and indexed to define some important geometrical characteristics, and malformation of body and fruit stalk which are necessary for the design of the equipments for cutting, spreading and alignment of red pepper in developing a fruit stalk remover of fresh red pepper. The effects of bending of body and fruit stalk on the equipments of cutting, spreading and alignment were studied. The maximum lengths of some parts of fresh red pepper were found to be 180 mm, 125 mm, 144 mm, 67 mm and 76 mm for the body, the bent part of body, the fruit stalk, the bent part and the straight part of fruit stalk, respectively. The fresh red pepper with bending indices more than 0.4 and 0.3 for the body and the fruit stalk, respectively, was defined to be malformed based on the result of cutting rate using cutting unit; while the other ones to be normal in shape. Based on this, among the total fresh red peppers tested, 47%, 40% and 20% were found malformed for the body, the fruit stalk, and for both of the body and the fruit stalk. Malformed red peppers were poorer in spreading and alignment than normal ones, and the processed quantity was decreased with increased feed rate. The required time for the malformed peppers to pass on the alignment plate inclined at 30 increased rapidly at 8.3 Hz with increased feed rate. For the fresh red peppers with average moisture content of 85%,w.b., the maximum tensile strength between fruit stalk and body was 88.1 N; the maximum cutting resistances were 92.1 N and 94.9 N for the fruit stalk-calyx joint and body, respectively. Average coefficients of static friction were 0.99, 0.62, 0.59 and OJ, respectively, for the surfaces of rubber, galvanized iron, acryl and plywood.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.15 no.4
• /
• pp.238-244
• /
• 1995

The objective of this study is to obtain the basic data for investigating the effects of organic reserves on winter survial or regrowth yield. Forage rape(Brassica napus L.) was sown on Sep. 1, 1994. Experimental plots were divided into three replicates under 6 different cutting dates(l0 days interval from Oct. 15 to Dec. 4). Field-grown palnts were sampled on the each cutting date and on the wintering period (Jan. 16) to analyze the nitrogen and non-structural cahohydrate reserves. The rate of winter survival and regrowth yield were also measured in the spring of next year. On the before wintering, dry matter yields were 152, 274, 500, 718, 776 and 981 kg/lOa, respectively, from the cutting date on Oct. 15, Oct. 25, Nov. 4, Nov. 14, Nov. 24, and Dec. 4. Cmde protein yield significantly increased as cutting date was later until Nov. 14, thereafter a significant increase did not occured. Nitrogen and starch contents per plant significnatly increased as the cutting date was later. The increasing rate of starch was greatly higher than that of nitrogen. On the wintering period, nitrogen reserves in mts were 85.3, 68.8, 47.6, 28.3, 44.3, and 55.3 mglplant, and starch reserve were 11 1.3, 75.3, 39.3, 19.6, 26.4 and 34.6 mglplant, respectively, in the plots cut on Oct. 15, Oct. 25, Nov. 4, Nov. 14, Nov. 24, and Dec. 4. It showed that carbohydrate reserves were much highly utilized than nitrogen reserves during wintering period. The rates of winter survival were 91, 83, 46, 22, 35 and 43% and regrowth yields were 692, 545, 316, 84, 127 and 140 kgD.M/lOa, respectively, in each plots. The highly significant correlation (p<0.01) between the level of organic reserves and the rate of winter survival or regrowth yield were obtained.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.8 no.1
• /
• pp.21-29
• /
• 2006

When apples are picked or selected by grader, the rate of wound occurrence on the skin by apple stalk is remarkably high if the apple was bigger than 3 size during the harvest time. Except this case, the other sizes showed very little similarity. The crop of apple per 1 minute was 2.9kg without cutting fruit stalk, whereas only 1.1kg of the apples were obtained due to cutting the fruit stalk. Thereby, the harvesting without cutting fruit stalk is highly effective in terms of productivity rather than cutting the fruit stalk. As far as the wound occurrence rate on apple skin by apple stalk of distance between grader's dish and accumulated board is concerned, the grader which has no distance showed quite low rate of wound occurrence compared with those grader with 3cm or 8cm distance. When the apple was being stored, there was no difference in firmness between the cut stalk apple and the uncut stalked apple, however there was slightly more weight loss in the cut stalk apple than uncut stalk apple.