• Journal of Trauma and Injury
• /
• v.36 no.1
• /
• pp.32-38
• /
• 2023

Purpose: This study aimed to identify the characteristics of patients injured by high-rotation cutting tools and the factors related to the severity of their injuries. Methods: Adult patients (≥18 years), who presented to the emergency department (ED) after a high-rotation cutting tool injury and who were registered in the Korean Emergency Department-based Injury In-Depth Surveillance (2011-2018) database, were included. Patients' demographic characteristics, injury-related factors, and Injury Severity Scores were collected. All included cases were categorized into two groups according to the tool that caused the injury: grinder versus nongrinder. The characteristics of the two groups were compared, and the factors associated with the severity of injuries were investigated. Results: Among 8,697 ED visits, 4,603 patients had been using a grinder and 4,094 had been using a nongrinder tool. The most frequently injured body part while using a grinder was the hand (46.4%), followed by the head (23.0%). While using a nongrinder tool, the most frequently injured body part was also the hand (64.0%), followed by the lower leg (11.4%). The odds of a severe injury were affected by patient age (odds ratio [OR], 1.024; 95% confidence interval [CI], 1.020-1.028) and using a grinder (OR, 2.073; 95% CI, 1.877-2.290). The odds of a severe injury using a grinder were higher in arm injuries (OR, 1.60; 95% CI, 1.40-1.83) and multiple-part injuries (OR, 1.998; 95% CI, 1.639-2.437). The odds of a severe injury using a grinder were lower for head injuries (OR, 0.481; 95% CI, 0.297-0.781). Conclusions: Injuries from grinders were more likely to affect the head and neck than nongrinder injuries, despite the lower severity. The current lack of regulations on grinders in occupational safety and health standards warrants relevant legislation and the development of applicable safety equipment.

• Korean Journal of Environmental Agriculture
• /
• v.37 no.2
• /
• pp.87-96
• /
• 2018

BACKGROUND: The vigorous shoot growth in upper part of apple tree canopy leads to poor fruit quality and flower bud formation in lower part of canopy. So, this study was conducted to develop the proper control method about the shoot growth in upper part of apple tree canopy. METHODS AND RESULTS: Trunks of 'Fuji'/M9 apple trees were cut (back pruned) to 2.5 m in tree height on 11 February (dormant) or 12 April (full bloom). Naphthalene acetic acid (NAA) was applied at 2.0% to cut surface when trunk was pruned. Prohexadione-calcium (Pro-Ca) was sprayed at 250 mg/L above 2.0 m in tree height at 23 April (petal fall). The NAA or Pro-Ca application after trunk was pruned at dormant (TR-2 and TR-3) significantly reduced shoot growth in upper part of canopy compared with the control (tree was only pruned at dormant, TR-1), but the percent of shoots showing the secondary growth of TR-3 was higher over 2 times than that of TR-2. The reduction of shoot growth in upper part of canopy by TR-2 and TR-3 increased the fruit red color from the lower part in the treating year and blooming of the lower part in the following year. CONCLUSION: Applying 2.0% NAA to cut surface of pruned apple trunk at dormant was the most effective way for stabilization of the tree vigor in upper part of the canopy in a high density apple orchard.

• Journal of Navigation and Port Research
• /
• v.46 no.5
• /
• pp.458-470
• /
• 2022

As the 4th industrial revolution progresses, the application of several cutting-edge technologies such as the Internet of Things, big data, and mixed reality (MR) in relation to autonomous ships is being considered in the maritime logistics field. The aim of this study was to apply the concept of a digital twin model based on Human Machine Interaction (HMI) including a digital twin model and the role of an operator to a ship. The role of the digital twin is divided into information provision, support, decision, and implementation. The role of the operator is divided into operation, decision-making, supervision, and standby. The system constituting the ship was investigated. The digital twin system that could be applied to the ship was also investigated. The cloud-based digital twin system architecture that could apply investigated applications was divided into ship data collection (part 1), cloud system (part 2), analysis system/ application (part 3), and MR/mobile system (part 4). A Mixed Reality device HoloLens was used as an HMI equipment to perform a simulation test of a digital twin system of an 8 m battery-based electric propulsion ship.

• Journal of Sericultural and Entomological Science
• /
• v.19 no.1
• /
• pp.1-4
• /
• 1977

This work was carried out to know the relation between the yield and the cutting length of mulberry branches in autumn. The results obtained are summarized as fellows, 1. Most of the experimented mulberry trees grew evenly, of which branches showed 171cm to 177cm in average length. 2. No difference could be seen in autumn yield among the treatments, however, the shorter branches were remained, the higher in ratio of re-sprouting bud. 3. The spring yield of cutting mode in 100cm and 200cm remained was as much as non-treatment, but dropped remarkably in below 80cm remained. The high productivity in the 100cm or above renamed mode accounts for the low ratio of no-sprouting bud and accelerating the growth of the shoot, which consequently become much of shoot yield per 1m of branch. By cutting branches, however, the ratio of amount of leaves per shoot became low. 4. The cutting mode in 100cm and 120cm remained can yield as much as non-treatment even in the total yields of spring and autumn. but 100cm mode seems to be more advanceable in autumn owing to a little sparing labor for picking leaves. Thus, the most desirable cutting mode in autumn may be in 100cm remained, which usually has been done at the part of one third or half of the whole branches.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10b
• /
• pp.1576-1579
• /
• 1991

This paper discusses on the machine loading and tool allocation (MLTA) problem. Mathematical formulation of the problem is given first. Then a heuristic approach based on Group Technology (GT) is presented to deal with the MLTA problem effectively. By using this approach, part-tool group generation and their assignment to adequate machines can easily be obtained in consideration of the work load on each machine, the number of tool-set replacement, and the total number of cutting tools required through the interactive setting of the desired machine utilization rate.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.1050-1053
• /
• 1995

A stock removal cycle is developed as a programming tool of the CNC lathe. This cycle support the easiness and swifness of a part program generation in the shopfloor. The cycle contains the function of tool path generation of rough/finish cutting, of avoidance air-cut for non-cylindrical (die-casted, forged) workpiece, and of the tool collisopn detection/aviodance. Consequently the intelligent stock removal cycle results in improving the productivity and safety of CNC lathe.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.10a
• /
• pp.26-31
• /
• 1998

The effect of tool angles on the surface roughness in face milling is studied. First, the relation between tool angles and rotation angles is identified. Using this relationship, it is obtained that the projection of insert nose shape on cutting profile, which is a part of ellipse. The effect of spindle tilt is also considered for the tool angles. It si shown that tool angles along with nose radius and feed rate have an effect on surface roughness.

• Proceedings of the Safety Management and Science Conference
• /
• 2002.05a
• /
• pp.215-219
• /
• 2002

In this paper some physical evidences indicate that reduced friction occurs in an cryogenic machining process, in which LN2 is applied to the selected cutting zone. LN2 also reduced the tool wear rate to a great extent and elongated the tool life up to four times compared to emulsion cooling.

• Proceedings of the Safety Management and Science Conference
• /
• 2002.05a
• /
• pp.221-225
• /
• 2002

Machinability improvement by the use of liquid nitrogen in cryogenic machining has been reported in various studies. This has been mostly attributed to the cooling effect of liquid nitrogen. However, No study has been found in discussion on whether liquid nitrogen possesses lubrication effect in cryogenic cutting. This paper presents lubrication mechanism related to chip microstructure. The friction reduction was further reflected In larger shear angle and less secondary deformation in the chip microstructures.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.579-584
• /
• 2000

Single crystal silicon (SCS) is used in a variety of microsensor applications in which stresses and other mechanical effects may dominate device performance. The authers model temperature dependent mechnical properties during focused io beam(FIB) cutting and Pt deposition processes. In microaccelero-meter manufacturing process, this paper intend to find thermal displacement change of the temperature by tunnel gap, additional beam part and pt deposition. The thermal analysis intend to use ANSYS V5.5.3.