• Journal of the Society of Naval Architects of Korea
• /
• v.31 no.4
• /
• pp.119-129
• /
• 1994

The aim of the present study is to derive an empirical formula relating the absorbed energy and the cutting length for longitudinally stiffened steel palates which are cut by a wedge, idealizing the ship bottom stiffened platings in groundings. This study is based on the test results and the investigations of some parameters affecting the cutting response, described in Part I. By dimensionless ana1ysis of the test results obtained in a quasi-static loading condition, the energy absorbed while a longitudinally stiffened plate is cut by a wedge is expressed as functions of the cutting length, the yield stress, the equivalent plate thickness and the wedge angle. Also, the dynamic effects are incorporated into the static formula such that the proposed formula can be applied to the impact loading situations. The validity of the proposed formula is checked by comparing with the results obtained by the other existing formulas or by the drop-hammer tests.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.11
• /
• pp.67-73
• /
• 2021

Tanks are key weapons of ground combat that are equipped with powerful weapons and have strong protective bodies. One tank component, the engine clutch flange, is located in the part of the tank where the engine and transmission are installed, and it is a key part of the power transfer and shutoff. The engine clutch flange transmits high power to secure the mobility of the tank; thus, it must have high strength and hardness. In addition, high durability and safety must be ensured because tank operations must exclude concerns about damage. In this study, an engine clutch female flange for tanks made of SNCM439 was developed. The 2D design used AutoCAD programs, and the 3D shape design used CATIA programs. The structural analysis was conducted using ANSYS. The mesh grid has a tetrahedron shape and is created by adding a mid-side node. After the mechanical properties and constraints of SNCM439 were entered, the changes in the safety factor, total deformation, and Von-Mises stress were identified according to the increase in torque. Prototype processing was performed to verify the engine clutch female flange for the tank. To determine the productivity of the product, the cutting processing time was measured when processing the prototypes. Based on the results of measuring the cutting processing time, it is concluded that research is needed to improve productivity because MCT slot cutting processing is time consuming.

• Journal of Biosystems Engineering
• /
• v.35 no.1
• /
• pp.37-45
• /
• 2010

Since SRC (Short-term Rotation Coppice) such as poplar and willow can be harvested in three years, they are known to be a potential forest biomass as fuel for a power plant. The production system including transplanting and harvesting is, however, necessary to be mechanized because such a biomass should be handled in a massive volumetric size. A pull-type stem-cutting transplanter was developed in the research as the first step to realize the production of SRC. A needle-like transplanting device pushes a stem-cutting into the prepared soil bed by a pneumatic cylinder, and another device firms soil around a stem-cutting transplanted. Since this is an intermittent operation, it was necessary to develop a zero horizontal velocity mechanism which enabled only the transplanting needle part to continue a zero horizontal movement relative to the ground during the transplanting operation even when the tractor kept moving forward. The 2-row transplanter can transplant stem-cuttings at the rate of 6.5 seconds per row without missing a single attempt. The planting depth and distance were well maintained and controlled. Their CVs were between 2.1~3.4% and 0.87~1.7% for the depth and the distance, respectively. Although, the transplanted stem-cuttings tended to lean outward from the back-view and forward from the side view, they were planted within the range of $3^{\circ}$ from the upright position.

• The Journal of Engineering Geology
• /
• v.14 no.4 s.41
• /
• pp.451-460
• /
• 2004

The strength of sliding plane is usually assigned on the whole sliding plane with same value in 2D limit equilibrium slope stability method. However, the potential sliding plane is divided into two or three parts which have different sliding resistances. According to the calculation results of 3D slope stability analyses using 4 types of slope cutting models, marginal sliding resistance could affect the safety of slope significantly. In this calculation two kinds of the sliding plane strengths were applied differently to the parts of bottom and margin of the model slope. The effect of marginal resistance was calculated quantitatively. In case of lower sliding resistance of the bottom, the safety factor becomes low in a margin cutting model. However, in case of higher sliding resistance of the bottom, the safety factor decreased slightly in a lower part cutting model and increased in a upper margin cutting model.

• Journal of the Korean Society of Costume
• /
• v.33
• /
• pp.217-228
• /
• 1997

The purpose of this study was to investigate influence of the construction method of the circular skirt on drapability and shape of static silhouette and length variation. In made 24 types of skirts giving the variations (six kinds of peach skin-like finished fabrics two types of cutting method two types of machine stitch method of hem), The results were as follows: 1. Analysis of drapability In the cutting method thre was similarity between warp direction and true bias direc-tion. In the machine stitch method of hem there was similarity between blind stitch and blind stitch machine. According to the fabrics analysis of drapability was excellent in the order N/P 80/20(fabric 1)>P 100(fabric 5)>P 100(fabric 6)>P 100 (fabric 2)>P 100 (fabric 4)>N/C 50/50(fabric 3). 2. Analysis of the characteristics values of static silhouette shape In the cutting method shape of static sil-houette became wide in the warp direction. In the machine stitch method of hem shape of static silhouette became wide in the blind stitch. According to the fabrics shape of static silhouette became most wide in the N/C 50/50(fabric 3) and shape of static sil-houette become most narrow in the P 100(fabric 2,5) 3. Analysis of the length variation In the cutting method the true bias direc-tion was longer than the warp direction. In the machine stitch method of hem there was simi-machine stitch method of hem there was simi-larity between blind stitch and blind stitch ma-chine. In fabrics the P 100(fabric 6) showed the longest the N/C 50/50(fabric 3) showed most slight. Interaction between the cutting and messure-ment part of skirt lengh. In the warp diretion parts that showed longest length variation were C. G, K, O in the true bias diretion parts that showed most slight length variation were A, E, M, I.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.1
• /
• pp.120-130
• /
• 1994

The leadwire cutting machine that has been used recently cuts leadwires by putting one-side force with the same priciple as a saw, and applies a stress at soldered part of PCB. Because the stress becomes one cause of contact-defect, a leadwire cutting robot that cuts leadwire-site with nipper and does not apply stress is considered, In this paper a technique of detecting leadwire-site is studied for the purpose of using on automatic leadwire cutting robots. A technique deriving 2-dimensional site-information with many I-dimensional binary data of perspective front-view of PCB taken from various direction was proposed. Simulation and experiments were done under the same condition each other and a small universal PCB was choosen as an experimental object. As a result of simulations and experiments, the proposed technique turns out to be very useful for automatic leadwire cutting robots.

• Journal of Fashion Business
• /
• v.16 no.4
• /
• pp.29-45
• /
• 2012

The purpose of this study is for providing not only the latest design technique trend for zero waste fashion, but information about creative fashion design education through eco-fashion industry trend in globally and domestic which is focusing on eco-fashion labelling. The research were processed with literature related eco, sustainable, green fashion books, former articles, newspapers, and web sites. The results as follows; The certification about eco-fashion product is moving to 'Life Cycle Assessment' from focused on primary process like material, finishing, dyeing. Especially simplicity of process means reducing the wastes. And fabric wastage for adult outwear was estimated 15% percent of total fabric used in general design studios. Three cases for Zero waste fashion were as follows; First, Jigsaw puzzle by Timo Rissane and Mark Liu were different zero waste methods, but the result was same. Rissene's method was based on traditional cutting like 'cut and sew' but traditional cutting can lead to design that have an abundance of fabric and drape. Jigsaw of Rissene was approached with description a pattern-cutting technique in which all piece interlock with each other generating no waste from design production. Another Jigsaw by Liu was related with innovative textile design. DTP makes the possibilities for zero waste garment production almost endless. The dress intricately cut from 10 pieces, wastes none of the fabric required to make it. Second, Subtraction Cutting by Julian Roberts provides unexpected fluid, organic forms and zero waste fabric. Utilizing Roberts plug(tunnel) technique enables any part of the garment that is removed for fit or aesthetics to be reincorporated into the design of garment. Third was 'Bio Couture' by Suzanne Lee. She has created garments from cellulose bacteria which grow in a bathtub using only green methods addressing in such as way ecological issues and exploring the future of fashion design in conjunction with technology.

• Journal of Bio-Environment Control
• /
• v.26 no.4
• /
• pp.242-248
• /
• 2017

This study was conducted to develop a cylindrical paperpot manufacturing equipment which is capable of continuously producing paperpots with a constant size. The equipment consists of the soil supply part, the paper supply part, the pot manufacturing part, the paperpot cutting part and its process for manufacturing paperpot from the soil supply to the paperpot cutting is continuously performed. As a result of the performance test using this equipment, we suggest that the optimal moisture content and injection pressure to supply soil are 50%~60%, and 0.5 Mpa respectively. Moreover the appropriate temperature for adhesive strength is $150{\sim}160^{\circ}C$ taking into account the performance of device and adhesion time. Also, considering the cutting speed and safety, it is appropriate to adopt a straight blade having a clean plan at a minimum angle of $30^{\circ}$. In addition, the manufacturing capacity of the developed equipment was 3300 pots per hour.

• Journal of the Korean GEO-environmental Society
• /
• v.5 no.4
• /
• pp.73-79
• /
• 2004

Mountain side ditch is constructed at the top of cutting slopes around road and it drains the surface water that flowed from upper part. Mountain side ditch is constructed to keep away the influx of the surface water into cutting faces. However, if Mountain side ditch is constructed on the top of cutting slopes, it is cause of trouble. For example, difficulty of quality control and lack of drainage faculty. Therefore, the faculty and establishment propriety of mountain side ditch are evaluated seriously, according to the condition of ground, topography and rainfall in this paper. Results from the study for the numerical analysis of effect of mountain side ditch indicate that safety factor is enlarged about 3% at rainfall.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.8 no.4
• /
• pp.32-42
• /
• 2005

To investigate the plants invasion process and dominant species in large-scale cutting slopes, slopes elapsed one year to thirteen years after construction had been selected in five counties. The obtained results are summarized as follows : The species of high appearance frequency were Alnus firma, Arundinella hirta, Miscanthus sinensi var. purpurascens, Erigeron cancdensis, Artemisia princeps var. orientalis, Oenothera odorata, Lactuca raddeana, Lactrca indica var. laciniata, Lespedeza bicolor, Youngia sonchifolia, Populus albaglandulosa, and so on. The biological type of identified vascular plants was $Ch-D_1-R_{5-e}$. In time, plant coverage was increased gradually and average of plant coverage was 1.17% in slopes which elapsed one year, 42.44% after six years, 56.67% after eight years, and 69.17% after ten years. The dominant species in the surveyed slopes were covered with Alnus firma, Artemisia princeps var. orientalis, Erigeron cancdensis, Miscanthus sinensi var. purpurascens, Arundinella hirta, Lactuca raddeana, Oenothera odorata, Boehmeria spicata, Kummerowia striata and Artemisia montana of the 59 species. The conditions of location in large-scale cutting slopes are hard to fix and germinate of seeds, and extend plant roots in the slope soil. Hence, the highly appearance species and dominance species of the area will make plant coverage quick and slope stable.