• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.176-180
• /
• 2002

All types of VLM-s process include the linear heat cutting of EPS foam to generate a layer with 3D shape. The dimensional accuracy and part quality of the cut part are dependent on the thermal characteristics in the EPS foam. The thermal characteristics are determined by operating parameters such as an effective heat input and cutting angle. The objective of this study is to investigate into the influence of cutting angle on the kerfwidth and the melted length of the cut part using the numerical analysis and the experiments in generally sloped cutting with two cutting angles. In order to estimate an accurate temperature field, the transient thermal analysis using moving coordinate system, the fully conformed mesh and the heat flux model with two cutting angles is carried out. From the results of the analysis and the experiments, it has been found that the influence of the rotational angle about x-axis in which the rotational axis is normal with hotwire cutting direction is appreciably negligible in comparison with that of the rotational angle about y-axis.

• 열처리공학회지
• /
• 제6권1호
• /
• pp.1-8
• /
• 1993

In this paper, the surface roughness influenced by Sm45C hardness in high frequency induction hardening and mechanical characteristics for the changed Hv 598 part and the unchanged hardness Hv 223 part by use of cermet and ceramic cutting tools was experimentally examined. Finally, we could be had some important results by processing surface roughness on cutting conditions such as cutting speed, feed rate, depth of cut and changes of tool nose radius. The results are summarized as follows. 1. In case of the same cutting condition, the hardness of workpiece was high and acquired the best processing surface roughness when the radius of the tool nose had 0.8 mm and feed rate was 0.04 mm/rev. 2. In case of the hardness of workpiece, though the cutting speed didn't have an effect on processing surface roughness, the less feed rate and the more processing surface roughness improved. On the other hand, the low inside the hardness of workpiece, the more cutting speed and the more feed rate increase, the processing surface of roughness improved. 3. Regardless of the hardness of workpiece, the change of the cutting depth didn't have great effect on the surface roughness. 4. On cutting the high surface hardness part with cutting tools of cermet and ceramic, it can be acquired the higher processing surface roughness because it hadn't been taken effect on cutting speed, In case of the cutting process of the low inside hardness part the two cutting tools have acquired the similar processing surface roughness.

• 한국정밀공학회지
• /
• 제17권12호
• /
• pp.185-194
• /
• 2000

Rapid Prototyping(RP) techniques have their unique characteristics according to the working principles: stair-stepped surface of parts due to layer-by-layer stacking, low build speed caused by line-by-line solidification to build one layer, and additional post processing to improve surface roughness, so it is required very high cost to introduce and to maintain of RP apparatus. The objective of this study is to develop a new RP process, Variable Lamination Manufacturing using linear hotwire cutting technique and expandable polystyrene foam sheet as part material(VLM-S), and to investigate characteristics of part material, cutting characteristics by using linear hotwire cutting system and bonding. Experiments were carried out to investigate mechanical properties of part material such as anisotropy and directional tensile strength. In order to obtain optimal dimensional accuracy, surface roughness, and reduced cutting time, addition experiments were performed to find the relationship between cutting speed and cutting offset of hotwire, and heat generation of hotwire per unit length. So, adhesion strength tests according to ASTM test procedure showed that delamination did not occur at bonded area. Based on the data, a clover-shape was fabricated using unit shape part(USP) it is generated hotwire cutting. The results of present study have been reflected on the enhancement of the VLM-S process and apparatus.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.143-148
• /
• 1995

A study on the generation of optimum tool path for machining the concave parts is discussed. Above all, the various cutting factors and their relationships are considered. Then optimum tool path for concave parts is generated on these cutting variables and their relationships. It is difficult for existing CAD/CAM systems tomachine the concave parts. For cutting the part even the experienced craft must give many attentions and muchtime since it needs consideration of various cutting conditions and geometric properties. The optimum tool path for the concave part is generated onnot only geometric properties byut also cutting conditions. We choose, as variables, feed and cutting direction for productivity, diameter of tool and constant(stable) cutting force for machining accuracy. The results are verified through simulation of the index of performance and cutting force.

• Design & Manufacturing
• /
• 제10권3호
• /
• pp.1-7
• /
• 2016

In the semiconductor industry the memory and chip were developed to high density memory and high performance chip, so circuit design was also high integrated and the test bed was needed to be thin and fine pitch socket. LGA(Land Grid Array) IC socket with thin wall thickness was designed to satisfy this requirement. The LGA IC socket plastic part was manufacture by injection molding process, it was needed accuracy, stiffness and suit resin with high flowability. After injection molding process the side gates were needed to remove for further assembly process. ln this study, the cold press cutting process was applied to remove the gates. For design of punch and die, the cold press cutting analysis was implemented by$DEFORM-2D^{TM}$ ln consideration of the simulation results, an adequate punch and die was designed and made for the cutting unit. In order to verify the performance of cutting process, the roughness of cutting section of the part was measured and was satisfied in requirement.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.155-156
• /
• 2007

This paper presents the vision-based camber and optimal cutting line detection algorithm for hot-rolling process. It is important to measure the camber of head and tail part of strips because many problems are caused by the camber in the hot-rolling process. The hot-rolling process has time constraints. The camber detection algorithm of head and tail parts requires fast and less complex for satisfying time constraints. The proposed algorithm consists of two parts: measurement of the camber in the head and tail part of strips and decision part of the optimal cutting line of hot-rolled strip. First, we obtain the camber value of the strip from the difference between the real center line and the center line of head, tail part. Second, the head and tail part of strips isn't suitable for strips connections. Therefore, the cutting process is needed in the hot-rolling process. The optimal cutting line is determined by the head and tail images obtained from cameras. The algorithm is applied into the vision system with two area cameras, Matrox image processing board and host PC for verification.

• 한국잠사곤충학회지
• /
• 제28권2호
• /
• pp.9-14
• /
• 1986

고조삽목의 실용화를 위해, 삽상의 종류, 상토, 삽목시기, 발근촉진제의 효과, 삽목전처리, 삼수채취부위 등을 연구한 결과 다음과 같은 결과를 얻었다. 1. 삽목방법 중 활착률이 가장 높은 구는 사토에서 유합조직을 형성시킨 후 삽목하는 구였으며, 보온못자리구에서는 완전히 고사하여 가장 낮았다. 2. 삽목적기는 3월 26일로 이때에는 수상자, 사토상토를 제외하고 활착률 100%를 보였다. 3. 삽목채취 부위별 활착률은 상<중<하부 순으로 높았으나, 유합조직구에서는 중부에서 70-100%의 높은 활착률을 보였다. 4. 발근촉진제 Rootone-F 포도는 지조상·중부, 그리고 온상 20cm구에서 포도하지 않은 것보다 활착률을 높였으나, 다른 구에서는 뚜렷한 효과가 없었다. 5. 상토의 토성은 활착률에 일정한 경향을 보이지 않는다. 6. 삽목전 처리 중 3월 15일 채취, 빙고에 저장하였다가 삽목하거나, 유합조직의 형성후 삽목하는 경우 타처리에 비해 현저히 활착률이 높았으며, 채취후 방치하였다 삽목하는 전혀 활착되지 않았다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.18-23
• /
• 2002

In this paper, The torque of CNC spindle motor during machining is estimated without speed measuring sensor. The CNC spindle system is divided into two parts, the induction spindle motor part and mechanical part. In mechanical part the variation of the frictional force due to the increment of the cutting torque and the effect of damping coefficient is investigated. Damping coefficient is found to be a function of spindle speed and not influenced by the weight of the load, while frictional force is a function of both the cutting torque and spindle speed. Experimental formulars are drawn for damping coefficient as a function of spindle speed and frictional force as a function of both cutting torque and spindle speed respectively, to estimate the cutting torque accurately. Graphical programming is used to implement the suggested algorithm, to monitor the torque of an induction motor in real time. Torque of the spindle induction motor is well monitored with 3% error range under various cutting conditions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 춘계학술대회 논문집
• /
• pp.97-101
• /
• 1993

In this work, the imaginary part of the inner modulation transfer function of the cutting dynamics is introduced for tool wear monitoring. Time-series method is utilized to construct the generalthree dimensional cutting dynamics whose imaginary part of the inner modulation transfer funcition shows the proportionality to tool wear at the natural frequency of the machine tool dynamics. This modelis reduced to single-input single- output model without altering the proporitonality characteristics to tool wear and implemented to the dual computer system in which one computer performs measurement while the other calculates the imaginary part of the inner modulation transfer function of th cutting dynamics by the batchleast square method. The values of the imaginary part at the natural frequencyof the machine tool structure in the cutting direction are compared to the one calculated during machining with a brand new tool to decide the current stants of the tool. The experiments shows the relevance of the proposed concept.

• 한국공작기계학회논문집
• /
• 제14권6호
• /
• pp.110-116
• /
• 2005

A single-piece-machined-part has superior characteristics to an assembly of several pieces of part especially for aircraft components. It is necessary to develop high efficient 'multi-head router machine' for machining a large size single-piece-part on a large scale. In this type machine, many cutting chips are generated. These chips should be removed automatically f3r productivity and part precision. In this study, the design evaluation of the cutting chip collecting apparatus for 'multi-head router machine' was complemented using performance test and finite element analysis.