• Journal of Animal Science and Technology
• /
• 제57권11호
• /
• pp.34.1-34.5
• /
• 2015

Himalayan dock (Rumex nepalensis) was evaluated for forage value and antinutrients under three, five and seven weeks cutting intervals in the temperate environment. Dry matter (DM) content was measured for each cutting interval. Forage quality parameters such as Crude Protein (CP), Acid Detergent fiber (ADF), Neutral Detergent Fiber (NDF), Calcium (Ca) and Phosphorus (P) were analyzed. Plants with seven weeks cutting interval gave higher DM yield. CP and P content were significantly higher for three weeks cutting intervals. Average CP contents were 31.38 %, 30.73 % and 27.32 % and average P content 0.58 %, 0.52 % and 0.51 % for three, five and seven weeks cutting intervals, respectively. Ca content did not differ significantly between cutting intervals. The average Ca content were 0.91 %, 0.90 % and 90 %, for three, five and seven weeks cutting intervals, respectively. Tannin and mimosine contents were not significantly different between cutting intervals. Average tannin contents were 1.32 %, 1.27 % and 1.26 % and mimosine 0.38 %, 0.30 % and 0.28 % for three, five and seven weeks cutting intervals, respectively. The study concluded that R. nepalensis could be a potential source of protein for livestock. The study also suggests seven weeks harvesting interval to provide plants with high dry matter yield, high forage quality and very low levels of anti-nutrients.

• 한국정밀공학회지
• /
• 제18권8호
• /
• pp.107-115
• /
• 2001

Drilling torque was measured indirectly using the spindle motor current and controlled in real time through feedrate manipulation in a machining center. The PID controller designed in the previous paper was applied to drilling torque control. A series of cutting experiments were performed for various cutting conditions. Experimental results showed that the drilling torque was well regulated at a given reference level by feedrate manipulation in all cutting conditions. The increase in the cutting torque and temperature according to the increase in machining depth was suppressed and the risk of the drill failure and the drill flank wear were reduced remarkably through cutting torque control. Moreover, the suggested cutting torque control system doesn\`t disturb the cutting process and is practical for industrial environment. Therefore, the proposed culling torque control system will contribute to productivity improvement in drilling process.

• 한국토양비료학회지
• /
• 제46권5호
• /
• pp.322-326
• /
• 2013

Many organic fruit growers adopt cover cropping in their orchards to improve soil properties. A field experiment was conducted to determine the effects of cutting frequency of cover crop (CF) and liquid manure application (LM) on green manure production (GMP) and returnable nutrient content (RNC) in pear orchard. The combined effects of CF and LM were tested at two levels, respectively, with liquid manure ($L_1$) and without liquid manure ($L_0$). After that, cover crops were cut once ($C_1$) and three times ($C_3$) in rye, and twice ($C_2$) and four times ($C_4$) in hairy vetch. The result showed that main factors related to green manure production were different depending on the species. In rye, LM was more effective in increasing the dry weight of cover crop and RNC than CF. In contrast, the parameters were more affected by CF rather than LM in hairy vetch. Thus, it is suggested that different management technique is needed depending on the cover crop species in order to maximize the green manure production in pear orchard.

• 생물환경조절학회지
• /
• 제17권1호
• /
• pp.60-65
• /
• 2008

돌나물의 노지 가을삽식을 위하여, 줄기의 삽수 부위(상부, 중부, 하부) 및 삽식 방법(점파, 조파 산파)에 따른 월동전후 생육특성을 조사하였다. 삽수부위에 따른 삽목후 40일째의 월동전 생육은 상부 삽수에서 초장, 근장, 줄기수, 지경수, 지상부 생체중 및 건물중 등에서 유의하게 높았으며, 월동후 개화전(May 10th) 생육은 개체당 줄기수, $m^2$당 지상부 생체중 및 건물중에서 하부 삽수보다 유의한 증가를 보였다. 삽식 방법에 따른 삽목후 40일째의 월동전 생육은 점파($10{\times}10cm$)가 조파나 산파보다 양호하였고, $m^2$당 지상부 생체중 및 건물중도 점파>산파>조파 순으로 높았다. 월동후 생육(May 10th)은 개체당 줄기수, $m^2$당 생체중 및 건물중에서 점파가 조파보다 유의하게 증가하였다. 돌나물의 가을 노지 삽식은 줄기 상부의 삽수를 이용하는 것이 월동 전후 생육 및 수량성에 유리하였으며, 삽식방법은 점파에서의 수량성이 가장 양호하였으나, 생력화를 위해서는 월동후 생체중에서 점파와 유의한 차이를 보이지 않은 혼파방법이 바람직할 것으로 기대되었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2000년도 토목섬유 특별세미나
• /
• pp.81-92
• /
• 2000

Green Slope(F.F.R : Fabric Form Reinforcement Method) is one of an environmental slope protection method at steep cutting sites. This method is that soil and rock at the steep slope is fixed using the environmental Fabric Form, Nail, Rock Bolt and Rock Anchor, And then, the surfaces covered with grasses or weeds. This method will be satisfied both safe slope protection and natural environment appearance. Green Slope is a useful method of the construction sites of steep cutting slopes.

• 복식문화연구
• /
• 제23권6호
• /
• pp.929-939
• /
• 2015

Zero-waste is sustainable development for ensuring continuous interactions with the environment as well as for the next generations, while expanding across industries. Zero-waste fashion design does not necessarily mean that we should stop making clothes in order to reduce waste, but we consider the social values of sustainability regarding the environment, humans, and profit. In particular, in the pre-use stage of zero-waste fashion design, fashion designers play critical roles. The purpose of this study is to develop a methodology for the realization of zero-waste fashion design through establishing the typology of zero-waste pattern making (ZWPM) as well as exploring the practical implications of zero-waste fashion design. For the realization of zero-waste fashion design that draws from pattern-making principals, this study categorizes zero-waste fashion design into zero-waste pattern cutting (ZWPC) and non-pattern cutting (NPC). ZWPC is based on drafting patterns on a piece of fabric, which can enable the sharing of patterns and processes, while NPC requires little- or non-cutting/sewing in optimizing a piece of fabric, bringing the possibility of creating indefinite forms. ZWPC is sub-categorized into tailored and non-tailored, and NCP into draped and folded. Then, by implementing the typology in undergraduate design programs, this study tests and completes the design methodology for the realization of zero-waste fashion design.

• 한국물환경학회지
• /
• 제20권2호
• /
• pp.163-169
• /
• 2004

Feasibility of using PE sheet laminated CSP(Corrugated steel pipe) to sewers were tested via corrosion and abrasion tests for PE sheet laminated CSP; 1) corrosion test for PE film and PE coated plate, 2) corrosion test for joint of PE sheet laminated CSP, 3) corrosion test for outside of PE sheet laminated CSP, and 4) abrasion test for inside of PE sheet laminated CSP. The results for the corrosion and abrasion tests are as follows. 1. Results for corrosion tests on PE films and zinc coated steel plates that were coated with PE films show that the surfaces of both PE were not changed compared to those of original PE samples. Furthermore, PE films maintained strong adhesion on the steel plates even though they were exposed to sewage and seawater provided cutting planes of the steel plates were treated with molding. But, results for corrosion tests on the spots that were previously cut off by a knife and a cutting planes of the steel plates were treated without molding show that steel plates have been corroded if they were exposed to sewage and seawater. 2. Results for corrosion tests on joints of PE sheet laminated corrugated steel using sewage show that gathering rust was observed at cutting plane of PE sheet laminated corrugated steel after 180 days, but PE film was not flaked off. However, PE film at cutting plane was flaked off when PE sheet laminated corrugated steel was exposed to seawater. Furthermore, flaking process was severely progressed at lockseam points of which the surfaces were not smooth. 3. Results for laying PE sheet laminated corrugated steel under the ground show that the surface of untouched PE film was almost identical to that of original PE film. However, the spots that were previously cut off by a knife and a cutting plane of PE sheet laminated corrugated steel have flaked off. 4. As a result of abrasion tests conducted with PE sheet laminated corrugated steel and sand, brilliance and thickness of PE was not greatly changed under the severe abrasion conditions. Therefore, the durability of PE sheet laminated corrugated steel for abrasion was determined to be good.

• 한국정밀공학회지
• /
• 제1권2호
• /
• pp.24-32
• /
• 1984

The object of the study is to discuss the effect of magic ink as a surface active substance on the mechanism of chip formation in oblique cutting. The Rehbinder effect has been known as a phenomenon that the mechanical strength reduces when the metal is coated with some surface active substances. In order to interpret these surface effects defined by Rehbinder, the influence on the shear strength of shear plane by coating surface active substances, cutting force by the depth of cut, surface roughness and hardness ratio were observed. The results are as follows: 1. By coating the magic ink on free surface of the forming chip, the effective shear angle increases, and the cuttinbg force and the deformed chip thickness decreases. 2. With the large inclination angle the effective shear angle increases, and the specific cutting force and the friction angle decrease. 3. Cutting of the coated surface improves the surface roughness and the hardness ratio drops, which means another Rehbinder effect.

• 한국경영과학회:학술대회논문집
• /
• 대한산업공학회/한국경영과학회 2000년도 춘계공동학술대회 논문집
• /
• pp.625-629
• /
• 2000

The objective of ECMS(Environmentally Conscious Manufacturing Systems) is to consider environmental effects through the entire product life cycle from product development stage to design, manufacturing, supplying, using and disposing stage. Recently, environment-oriented recycling, reusing and manufacturing technologies have been researched actively in every engineering fields. In the field of chemical engineering, HHS (Health Hazard Scores) which classifies and analyzes hazardous materials in production processes has been presented. Metal cutting processes also have a lot of harmful factors, and especially hazardous components in cutting fluids have been known to have a bad effect on workers and working area. However, research works such as HHS have been little accomplished in metal cutting processes. In this research, a environmentally conscious machining process is presented by classifying hazardous components in cutting fluids, by using LCA(Life Cycle Assessments) and HHS method, and by evaluating environmental effects from cutting fluids.

• 한국터널공학회:학술대회논문집
• /
• 한국터널공학회 2005년도 학술발표회 논문집
• /
• pp.359-371
• /
• 2005

The Cutting slope is to be minimized when a tunnel meets the contour of slope terrain at a right angle around its portal. However, a tunnel portal has been generally installed at a right angle to the longitudinal axis of a tunnel with no consideration of the intersection angle with the slope terrain. This sometimes tended to cause huge cutting slope that resulted in many disadvantage in terms of safty, economy and environment. Therefore, the minimization of cutting slope is studied by taking the intersection angle into account, and the result is compared with that by the conventional method. In addition a design method for the inclined portal to the tunnel axis is proposed through 3D-FEM analysis, also the applicable ground condition is suggested.