• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.968-973
• /
• 2003

As environmental restrictions have continuously become more strict, it has emphasized development of environment-friendly technologies. In cutting technology, it has been well recognized that cutting fluids might have undesirable effects on worker's health and working environment and, hence, recently there have been numerous attempts to minimize harmful effects of cutting fluids on environments. To minimize the use of cutting fluids in machining, conventional cutting fluids have been replaced with the technologies of pressurized cold air and minimum quantity lubrication(MQL). Compared with milling, turning is a continuous cutting process, where tools are continuously heated up and lack of lubricity could lead to tool wear and deteriorated surface roughness. In this study, it has been investigated how tool wear and surface roughness could be affected by cutting conditions, supply and cooling methods. The experimental results show that MQL technology is able to minimize harmful effects of conventional cutting fluids.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.1004-1007
• /
• 2001

This paper presents the experimental results to verify the environmental consciousness with economic balances due to cutting fluid behaviors, effectiveness in machining process. Even though cutting fluid improves the machined part quality through the cooling and lubracating effects, its environmental impact is also increased according to the cutting fluid usage. Because cutting fluid are used by experience than science on shop floors, its environmental impact are more serious to human health hazard, shop floor environments. In this study a few cutting parameters are adopted as the machinability index (i.e. ; tool wear and surface roughness), and aerosol mist diffusion rate of cutting fluid as the environment consciousness index. These indeces are analyzed quantitatively via a few experiements. The results of this study can be facilitate the optimization of cutting fluid usage in achieving a balanced environmental consciousness consideration with economic view.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.6
• /
• pp.1007-1013
• /
• 2003

As environmental restriction kas continuously become more strict, machining technology has emphasized on development of environment-friendly technology. In cutting technology, it has been well recognized that cutting fluids might have undesirable effects on workers health and working environment. In this study, compressed cold air was used as a replacement for conventional cutting fluids. The cooling effect on cutting tool was analyzed using the finite element method and the computational fluid dynamics. This study focused on the temperature simulation of cutting tool by real flow analysis of cold air. The maximum flow rate and the minimum temperature of compressed cold air are 300ι/min and -30$^{\circ}C$ respectively. To compare the simulation and experimental results, inner temperature of the cutting tool was measured with the thermocouple embedded in the insert. The results show that the analysis of cutting temperature using FEM and CFD is resonable, and the replacement of cutting fluid with cold air is available.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.297-301
• /
• 2002

High-speed machining generates concenter thermal/frictional damage at the cutting ed rapidly decreases the tool life. This paper I at determining the effect of cutter orienter the cutting environment on tool life, tool mechanism when down milling. In this paper, experiments were carried out in various tool and cutting environments, such as dry, wet compressed chilled air, tool life were measu evaluate machinability in high-speed milli difficult-to-cut material and die steel, Tool measured in horizontal upwards, horiz downwards, vertical upwards and vert downwards. In addition, tool life was measur dry, wet and compressed chilled air. For this a compressed chi1led-air system was manufact The results show that a horizontal cutter ori provided a longer tool life than a vertical orientation. With respect to the cutting envi compressed chilled air increased tool life. H the wet condition decreased tool life due thermal shock caused by excessive cooling high-speed mill ins and the compressed chilled had little effect.

• Journal of Korean Society on Water Environment
• /
• v.23 no.3
• /
• pp.348-355
• /
• 2007

We investigated temporal changes of composition, habitat area, growth rate and elements content of hydrophytes at the artificial vegetation island (AVI) in Kyungan Stream within Lake Paldang. We also assessed nutrient removal rate through cutting off the emergent part of hydrophytes. The kinds of hydrophytes have increased from four species (P. australis, P. japonica, T. angustifolia and the Z. latifolia) at initial stage of installation to more than 29 species for 6-year operation. P. japonica was most dominant species at the AVI in 2006. The habitat area of have increased about 2.5 times compared to the initial planting area, occupying 63% of AVI's vegetation area. The incoming species of S. fluviatilis and B. frondosa have adapted successively and expanded habitat area in the AVI. The relative growth rate of P. japonica and P. australis was highest in spring sprouting period. Their hights and weights have increased until summer, by the time they were cutting off the emergent part. They started regrowth immediately after cutting and continued to grow until September and withered away in November. The carbon contents of P. japonica and P. australis have increased during growth phase, on the contrary, the nitrogen and phosphorus contents have decreased. By cutting off and removing the emergent part (leaves and branches) of hydrophytes twice from AVI, $17.6gN/m^2/y$ of nitrogen and $1.3gP/m^2/y$ of phosphorus was removed from AVI in 2006.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.245-250
• /
• 2003

This research conducted milling tests to study effects of cutting environment conditions of ball end mills on the characteristics of hard milling process. KP4 steels and STD11 heat treated steels were used as the workpiece and WC-Co ball end mill tools with TiAIN coated were utilized in the cutting tests. Dry cutting without coolant and semi-dry cutting using botanical oil coolant were conducted and MQL (Minimum Quantity Lubricant) device was used to spray coolant. Cutting forces, tool wear and surface roughness were measured in the cutting tests. Results showed that dry cutting of KP4 and hardened STD11 specimens produced better surface quality and wear performance than MQL spray cutting did.

• Transactions of Materials Processing
• /
• v.13 no.1
• /
• pp.45-52
• /
• 2004

This research conducted milling tests to study effects of cutting environment conditions of ball end mills on the characteristics of hard milling process. KP4 steels and STD11 heat treated steels were used as the workpiece and WC-Co ball end mill tools with TiAlN coated were utilized in the cutting tests. Dry cutting without coolant and semi-dry cutting using botanical oil coolant were conducted and MQL(Minimum Quantity Lubricant) device was used to spray coolant. Cutting forces, tool wear and surface roughness were measured in the cutting tests. Results showed that dry cutting of KP4 and hardened STD11 specimens produced better surface quality and wear performance than MQL spray cutting did.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.238-244
• /
• 2004

This research conducted milling tests to study effects of cutting environment conditions of ball end milts on the characteristics of high speed milling cutting process. KP4 steels and STD11 heat treated steels were used as the workpiece and WC-Co ball end mill tools with TiAIN coated were utilized in the cutting tests. Dry cutting without coolant and semidry cutting using botanical oil coolant by the MQL(Minimum Quantity Lubricant) device were conducted. Cutting forces, tool wear and surface roughness were measured in the cutting tests. Results showed that MQL spray cutting of KP4 and hardened STD11 specimens produced better surface quality and wear performance than dry cutting did.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.32-37
• /
• 2002

High speed machining is one of most effective technologies to improve productivity. It can give great advantage for manufacture of die and Moulds. However, when the high speed machining of materials, especially in machining of micro groove, a severely thermal demage was generated on workpiece and tool. Generally, the cutting fluid is used to improve penetration, lubrication, and cooling effect. In order to rise the performance of lubrication, it contains extreme pressure agents (Cl, S, P). But the environment of work room go bad by those additive Therefore, the compressed chilly air with Oil mist system was developed to replace the conventional cutting fluid system. This paper carried out the tests to evaluate the machinability by the cutting environment in high speed micro groove machining of NAK80 (HRC40). Compressed chilly air with oil mist was ejected on the contact area between cutting edge and workpiece. The effectiveness of this developed compressed chilly air with oil mist system was evaluated in terms of tool life. The results showed that the tool life of carbide tool coated TiAIN with compressed chilly air mist cooling was much longer than with dry and flood coolant when cutting the material.

• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.2
• /
• pp.71-76
• /
• 2003

A virtual machine tool (VMT) is presented in this two-part paper. In Part 1, the analytical foundation for a virtual machining system is developed, which is envisioned as the foundation for a comprehensive simulation environment capable of predicting the outcome of cutting processes. The VHT system undergoes "pseudo-real machining", before actual cutting with a CNC machine tool takes place, to provide the proper cutting conditions for process planners and to compensate or control the machining process in terms of the productivity and attributes of the products. The attributes can be characterized by the machined surface error, dimensional accuracy, roughness, integrity, and so forth. The main components of the VMT are the cutting process, application, thermal behavior, and feed drive modules. In Part 1, the cutting process module is presented. When verified experimentally, the proposed models gave significantly better prediction results than any other methods. In Part 2 of this paper, the thermal behavior and feed drive modules are developed, and the models are integrated into a comprehensive software environment.vironment.