• 한국정밀공학회지
• /
• 제18권2호
• /
• pp.84-89
• /
• 2001

In recent years, there is increasing demand of esthetic design and complex function in aerospace, automobile and die/mold industry, which brings into limelight high-precision, high-efficient machining of sculptured surface. This paper deals with the establishment of the optimal tool path on free form surface in high speed ball end milling. Ball end milling is widely used for free form surface die and mold. In this machining, the cutting direction was changed with tool path. The cutting characteristics, such as cutting force and surface form are varied according to the variation of cutting directions. In this paper, the optimal tool path with down cutting in free form surface cutting is suggested.

• 한국기계가공학회지
• /
• 제15권2호
• /
• pp.111-117
• /
• 2016

The cutting performance of a developed small-angle spindle tool was investigated with Al6061 using a TiAlN coated high-speed steel end mill. Up-cut and down-cut processes in a milling machine were carried out at the range of 1000-4000 rpm for spindle speed and 50-300 mm/min for feed rate. As a result, the highest cutting force in the Fx direction was obtained from the up-cut process when the spindle speed was 1000 rpm and the feed rate was 100 mm/min. In the Fy direction, the highest cutting force appeared in the up-cut process at a feed rate of 250 mm/min at the same spindle speed. Conversely, the lowest cutting force came out in the up-cut process at a spindle speed of 4000 rpm and a feed rate of 50 mm/min. As for surface finish, the finest surface roughness was obtained as Ra 0.7642 um at a spindle speed of 4000 rpm and a feed rate of 50 mm/min. Consequently, given the cutting performance of the developed small-angle spindle tool, we conclude that its use in industrial practice is feasible.

• 반도체디스플레이기술학회지
• /
• 제16권2호
• /
• pp.79-84
• /
• 2017

This paper outlines the Taguchi optimization methodology, which is applied to optimize cutting parameters in end milling when machining STS304 with TiAlN coated SKH59 tool under up and down end milling conditions. The end milling parameters evaluated are depth of cut, spindle speed and feed rate. An orthogonal array, signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are employed to analyze the effect of these end milling parameters. The Taguchi design is an efficient and effective experimental method in which a response variable can be optimized, given various control and noise factors, using fewer resources than a factorial design. An orthogonal array of $L_9(33)$ was used. The most important input parameter for cutting force, however, is the feed rate, and depending on the cutter rotation direction. Finally, confirmation tests verified that the Taguchi design was successful in optimizing end milling parameters for cutting force.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.52-57
• /
• 2000

STD11 is one of difficult-to-cut materials and its cutting characteristic data is not built enough. A bad cutting condition of it leads to low productivity of die and mould, so it is necessary to evaluate the machining characteristics of STD11. In this paper, the relations of the geometry of ball-end mill and mechanics of machining with it are studied. The helix angle of ball-end mill varies according to a location of elemental cutting edge in the cutting process are difficult to calculate accurately. To calculate instantaneous cutting forces, it is supposed that the tangential, radial and axial cutting force coefficients are functions of elemental cutting edge location. Elemental cutting forces in the x,y and z direction are calculated by coordinate transformation. The total cutting forces are calculated by integrating the elemental cutting forces of engaged cutting edge elements. This model is verified by slot and side cutting experiments of STD11 workpiece which was heat-treated to HRC45.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2005년도 춘계학술대회 논문집
• /
• pp.483-488
• /
• 2005

The complex three-dimensional miniature components are needed for a wide range of applications from the aerospace to the biomedical industries. To manufacture these products, micro machining that can make a high aspect ratio part and has good accuracy is widely researched. In this paper, cutting characteristics were analyzed in micro machining using cutting force coefficients, which are the specific cutting force for normal and frictional direction of rake surface. From measured cutting force in micro end milling, cutting condition independent cutting force coefficients were determined and used for analysing the characteristics of micro cutting. Using the cutting force coefficient, 써써써.

• 대한기계학회논문집
• /
• 제18권9호
• /
• pp.2211-2224
• /
• 1994

On face milling operation a new optimal cutter, which can minimize the resultant cutting forces, was designed from the cutting force model. Cutting experiments were carried out and the cutting forces of the new and conventional cutters were analyed in time and frequency domains. The resultant cutting forces were used as the objective function and cutter angles as the variables. A new optimal cutter design model which can minimize the resultant cutting forces under the constraints of variables was developed and its usefulness was proven. The cutting forces in feed direction of the newly designed cutter are reduced in comparison with those from the conventional cutter. The magnitudes of an insert frequency component of cutting force from the newly designed cutter are reduced than those from conventional cutter and the fluctuations of cutting force are also reduced.

• 대한기계학회논문집
• /
• 제7권1호
• /
• pp.36-45
• /
• 1983

In order to characterize the machine tool feed-drive dynamics, thread cutting experiments are performed with cutting conditions and slide-way lubrication varied. During the experiments, the carriage, tool post and tail stock accelerations in the feed direction are measured, and analyzed by employing the spectral analysis method. It is found that the tool post vibration in the feed direction during thread cutting operation is mainly due to those of the carriage and the workpiece. Other structure-related vibrations show little effects on the tool post vibration. The characteristics of the carriage vibration is shown to be fairly consistent, except the vibration amplitude, regardless the variations in cutting condition and lubrication within the experimental range. The experimental results suggest that the feeddrive system can be modelled as a 2 DOF damped oscillatory system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.553-556
• /
• 2003

End-milling have been used in the industrial world because it is very effective to the manufacture of mechanical parts with various shape. Recently the end-milling processing is needed the high-precise technique with good surface roughness and rapid time in aircraft, automobile part and molding industry. Therefore this study carried to decide the optimum cutting condition for surface roughness and rapid manufacturing time using design of experiment and ANOVA. From the results of experimentation, surface roughness have an effect on cutting direction, spindle speed and depth of cut. And then the optimum condition used Taguchi design is upward cutting in cutting direction, 600rpm in spindle speed, 240mm/min feed rate, 2mm in axial depth of cut and 0.25mm radial depth of cut. By using design of experiment, it is effectively represented shape characteristics of working surface in end-milling.

• 한국정밀공학회지
• /
• 제21권5호
• /
• pp.46-54
• /
• 2004

A cutting force model predicting the dynamic force induced by the axial vibration of it plate in face milling is introduced. When a plate face is milled, deformation in tool axial direction is considerable. Therefore, cutting forces are affected by not only inner-outer modulation in feed direction but also by axial deformation. A PTP (peak-to-peak) diagram made by the simulated dynamic force model is evaluated. The stability of the face milling process such as the chatter outset, and the stable cutting region can be simply estimated. Simulation results are compared with that of experiment.

• 한국의류산업학회지
• /
• 제6권4호
• /
• pp.497-502
• /
• 2004

The mechanical properties of jean slacks to the type of cutting lines in knee region and the bending time, after doing bending 0 times, 500 times, and 1500 times, the effects of whether or not cutting line, the fabric direction of the cutting area, and the number of cutting lines were investigated for tensile, shearing, compression, and mixing value of mechanical properties. The results are as follows: EM to bending times were larger in order of weft