• Clean Technology
• /
• v.22 no.4
• /
• pp.274-280
• /
• 2016

In this study, it was to develop a chemical method that can recycle the cutting oil which accounts for about 25% of the cost of the process among containing materials of silicon waste sludge generated in the process for producing a solar cell wafer. The 7 types of reagents have been used, including acetone, HCl, NaOH, KOH, $Na_2CO_3$, HF, $CH_2Cl_2$, etc. for this experiment. And It was carried out at a speed of 3000 rpm for 60 minutes centrifugation after performing a reaction with a waste sludge at various concentrations. As a result, the best reagents and conditions for separating the solid such as a silicon powder and a metal powder and liquid cutting oil were identified as 0.3 N NaOH. It is found to be pH 6.05 in a post-processing recycled cutting oil with 0.3 N NaOH after reaction of waste sludge and 0.1 N HCl which is effective to remove metal powder in order to adjust the pH to suit the properties of the weak acid is a commercially available cutting oil and it showed excellent turbidity than when applied to sludge with 0.3 N NaOH alone. The results of FT-IR analysis which can compare the properties of the commercially available cutting oil shows it has a possibility of recycling oil. The cutting oil recovery rate obtained through the experiment was found to be 86.9%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.359-361
• /
• 2006

As circuits become increasingly complex and devices sizes shrinks, the demands placed on global planarization of higher level. Chemical Mechanical Polishing (CMP) is an indispensable manufacturing process used to achieve global planarity. In the CMP process, Diamond Disk (DD) plays an important role in the maintenance of removal rate. According to studies, the cause of removal rate decrease in the early or end stage of diamond disk lifetime comes from pad surface change. We also presented pad cutting rate (PCR) as a useful cutting ability index of DD and studied PCR trend about variable parameters that including size, hardness, shape of DD and RPM, pressure of conditioner It has been shown that PCR control ability of pressure and shape is superior to RPM and size. High pressure leads to a decrease of cell open ratio of pad surface because polyurethane of pad is destroyed by pressure. So low pressure high RPM condition is a proper removal rate sustain. By examining correlations between RPM and pressure of conditioner, it has been shown that PCR safe zoneto satisfy proper removal rate has the range 0.06mm/hr to 0.12mm/hr.

• Culinary science and hospitality research
• /
• v.12 no.4 s.31
• /
• pp.299-319
• /
• 2006

The purpose of this study was to investigate the changes of hardness and microstructure of Dongchimi cooked with various sources of sugar(xylitol, xylose, sugar, pear juice). It was fermented at $10^{\circ}C$ for 60 days. The changes of pH in Dongchimi used different kinds of sugar decreased in all samples during the fermentation period, and then showed a slow decrease after 12 days of fermentation. The total acidity of Dongchimi using xylitol arrived slowly at the best tasting condition($0.3\sim0.4$ point) compared with other conditions. The changes of salt content were showed high as compared with other test conditions in 0 day, the day of fermentation. At the early stage of fermentation, the changes of turbidity of Dongchimi using sugar, pear juice were showed high as compared with those of Dongchimi using xylitol, xylose for $5\sim15$ days of fermentation. The maximum cutting force of Chinese radish Dongchimi showed the highest value among al at the 25 th day of ripening and then decreased gradually. The maximum cutting force of Dongchimi using sugar showed the lowest. The calcium and magnesium contents of Dongchimi juice and Chinese radish Dongchimi juice using xylitol were observed high at the early stage of fermentation and showed the highest value during the fermentation period. The microstructure showed disintegration appearance of middle lamella and cell wall during the fermentation period.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.299.2-299.2
• /
• 2013

We investigated the potassium remaining on a crystalline silicon solar cell after potassium hydroxide (KOH) etching and its effect on the lifetime of the solar cell. KOH etching is generally used to remove the saw damage caused by cutting a Si ingot; it can also be used to etch the rear side of a textured crystalline silicon solar cell before atomic layer-deposited Al2O3 growth. However, the potassium remaining after KOH etching is known to be detrimental to the efficiency of Si solar cells. In this study, we etched a crystalline silicon solar cell in three ways in order to determine the effect of the potassium remnant on the efficiency of Si solar cells. After KOH etching, KOH and tetramethylammonium hydroxide (TMAH) were used to etch the rear side of a crystalline silicon solar cell. To passivate the rear side, an Al2O3 layer was deposited by atomic layer deposition (ALD). After ALD Al2O3 growth on the KOH-etched Si surface, we measured the lifetime of the solar cell by quasi steady-state photoconductance (QSSPC, Sinton WCT-120) to analyze how effectively the Al2O3 layer passivated the interface of the Al2O3 layer and the Si surface. Secondary ion mass spectroscopy (SIMS) was also used to measure how much potassium remained on the surface of the Si wafer and at the interface of the Al2O3 layer and the Si surface after KOH etching and wet cleaning.

• Korean journal of food and cookery science
• /
• v.11 no.1
• /
• pp.83-91
• /
• 1995

For the accurate interpretation and objective measurement of textural characteristics of fermented vegetables, first of all, the studies on the microstructure and chemical compositions of vegetable cell, and the changes in the textural properties of vegetables during salting, blanching and fermentation should be carried out. And the mechanical textural parameters were needed to compare with and analyze in relation to the sensory parameters. In this review, the thypical force-distance curves of fermented vegetables were obtained from the compression, cutting and puncture test. And it was showed that the compression force was a more effective textural parameter to express the hardness of fermented vegetables, and the sensory chewiness and toughness were related to the changes in cutting force. In the puncture test, the puncture force was related to the hardness and varied with the size and form of puncture probe; the changes in puncture force by small probe could express the decrease in hardness and crispness, whereas those by large probe could represent the changes in toughness. And the brittleness and crispness could be measured by the break point and the numbers of peak obtained from the force-distance curves.

• Transactions of Materials Processing
• /
• v.14 no.3 s.75
• /
• pp.200-206
• /
• 2005

In general, a lot of small electrode is needed for making precision injection molds, such as cell phone mold and precision connector mold, because of the limitations of NC milling process. Those small electrodes usually have very simple shapes and the actual cutting time is so short, but many NC programs and set-up process, a very complicated and time consuming Job, are needed for each electrode. This paper deals the method for increasing the productivity of machining electrodes. In this work, the process standardization of machining electrode was done and special jig fer machining small electrodes was developed. Automatic tool path optimization software was also developed to minimize tool changing time. In addition, in-line cutting tool measuring system was adopted. The productivity of machining for small electrode has been increased up to $100\%$.

• Journal of the Semiconductor & Display Technology
• /
• v.16 no.3
• /
• pp.20-24
• /
• 2017

For process improvement and cutting down on expenses in solar cell industry, it is necessary to improve recycling process of wafer manufacturing. In this research, a study is introduced to develop classifier which is for recycling of abrasive. First of all, recycling process of wafer manufacturing is analyzed. And then, 3 steps of experiments such as oil removal, impurities removal and classification were executed. For the classification of slurry, a classifier is designed and manufactured. From experiments, it is verified that ultra sound vibration and flux are very important factors for classification. By experiencing the recycling processes and making devices, the technique can be initiated industry if needed such as decreasing waste and cutting down on expenses.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.33 no.6
• /
• pp.524-528
• /
• 2000

Effect of food additives on the heat sensitivity of listeria monocytogenes H-12 inoculated into Pollack surimi was investigated and also confirmed the effectiveness of various decontamination method such as tap water washing, chlorination, ultraviolet irradiation and heat treatment haying been applied on cooking utensils. Food additives such as polyphosphate, chitosan, and potassium sorbate increased heat sensitivity of t monocytogenes H-12 and polyphosphate showed the strongest synergistic effect. The tested strain was not detected from stainless steel and plastic cutting board contaminated with $10^4{\~}10^5/cm^2$ of L monocytogenes H-12 after tap water washing for 10 seconds or 1 minute, but washing effect was not found in wooden cutting board. The chlorination of stainless steel and plastic cutting board for 10 seconds with $5{\~}50 ppm$ solution eliminated all cells of the contaminated strain, however any change of the viable cell count was not observed in the chlorination of wooden cutting board, W irradiation on stainless steel and plastic cutting board for 5 minutes with 15 W above 30 cm eliminated the contaminated strain, but the tested strain was still found after 60 seconds of irradiation on wooden cutting board. The treatment of hot water on all used cutting boards for 10 seconds at $70^{\circ}C$ resulted in complete loss of viability of the contaminated strain.

• Journal of the Society of Naval Architects of Korea
• /
• v.57 no.6
• /
• pp.373-380
• /
• 2020

We have developed the hybrid prototype load cell structures. These developed load cell structures may increase the reliability of the load sensing by deriving the load values through the double sensing method through the vertical maximum deflection and bending stress of the simple beams. For this purpose, the structure design was performed so that the load value, the deflection and stress value could be output to the same value through the optimal structure design. The structurally designed dimensions reaffirmed the accuracy of the design through the structural analysis program and the matching of the load value and the deflection value. Based on the designed structural dimension, the prototype form was constructed through laser cutting and production using hot rolled steel materials. The developed prototype load cell structure can be used as good educational material in various subjects such as material mechanics, steel structure design, measurement engineering, and mechatronics engineering. It is also believed that the measurement system ideas can inform the occurrence of errors in the event of a problem, and if a major accident caused by a sensing error is predicted, it will show good utilization to prevent accidents.

• Journal of Embryo Transfer
• /
• v.7 no.2
• /
• pp.81-88
• /
• 1992

Cryopreservation of mouse embryos biopsied at 4-cell stage was investigated by ultrarapid freezing. Four-cell embryos were obtained from ICR mice on 55h after hCG injection. Zona pellucida of the embryos were partially dissected with a cutting pipet, and then single blastomeres were biopsied from the embryos followed by incubation in $Ca^2$+ and $Mg^2$+-free M16 medium for 30min. Biopsied embryos cultured for lh or 15h were frozen by ultrarapid freezing method using 3M DMSO or 5M glycerol as a cryoprotectant, respectively. The developmental rate of biopsied embryos after ultrarapid freezing and thawing to blastocysts was 81 % in the group of biopsied embryos cultured for lb and 98% in the group of biopsied embryos cultured for 15h, respectively. When biopsied embryos after ultrarapid freezing and thawing were transferred to the uteri of pseudopregnant recipients, normal live young were born. These results suggest that this freezing method can efficiently cryopreserve biopsied mouse embryos.