• Journal of Biosystems Engineering
• /
• v.4 no.1
• /
• pp.1-23
• /
• 1979

The use of barley seeder attached to rotary tiller in the rural area has a significant meaning not only for the solution of labor peak season, but also for the increase of land utilization efficiency. The facts that presently being used barley seeders are all based on the mechanical principles of the reverse rotation, center drive and are all using forward rotating tine, which is used to be easily and heavily worn out when it rotates reversely, raise problem of recommending them to rural area in Korea. Therefore, the main objective of the study was to develop new type of rotary tine attachable to barley seeders. To attain the objective the following approaches were applied. (1) The kinematic analysis of reverse rotating barley seeders. (2) The studies on the soil bin and artificial soil. (3) The comparative experiment on the power requirement of prototype tine. The results obtained from the studies are summarized as follow: 1. The kinematic analysis of barley seeder attached to rotary tiller: The following results were obtained from the kinematic analysis for deriving general formulae of the motion and velocity characterizing the rotary tine of barley seeders presently being used by farmers. a) The position vector (P) of edge point (P) in the rotary tine of reverse rotating, center drive was obtained by the following formula. $$P=(vt+Rcos wt)i+Rsin wt j+ \{ Rcos \theta r sin \alpha cos (wt- \beta +\theta r) +Rsin \theta r sin \alpha sin (wt-\beta + \theta r) \} lk $$ b) The velocity of edge point $(P^')$ of reverse rotating, center drive rotary tine was obtained by the following formula. $$(P^')=(V-wR sin wt)i+(w\cdot Rcoswt)j + \{ -w\cdot Rcos \theta r\cdot sin \alpha \cdot sin (wt-\beta +\theta r) + w\cdot Rsin \theta r\cdot sin \alpha \cdot cos (wt- \beta + \theta r \} k $$ c) In order to reduce the power requirement of rotary tine, the angle between holder and edge point was desired to be reduced. d) In order to reduce the power requirement, the edge point of rotary tine should be moved from the angle at the begining of cutting to center line of machine, and the additional cutting width should be also reduced. 2. The studies on the soil bin and artificial soil: In order to measure the power requirement of various cutting tines under the same physical condition of soil, the indoor experiments Viere conducted by filling soil bin with artificially made soil similar to the common paddy soil and the results were as follows: a) When the rolling frequencies$(x)$ of the artificial soil were increased, the densIty$(Y)$ was also increased as follows: $$y=1.073200 +0.070780x - 0.002263x^2 (g/cm^3)$$ b) The absolute hardness $(Y)$ of soil had following relationship with the rolling frequencies$(x)$ and were increased as the rolling frequencies were increased. $$Y=37.74 - \frac {0.64 + 0.17x-0. 0054x^2} {(3.36-0.17x + 0.0054x^2)^3} (kg/cm^3)$$ c) The density of soil had significant effect on the cohesion and angle of internal friction of soil. For instance, the soil with density of 1.6 to 1.75 had equivalent density of sandy loam soil with 29.5% of natural soil moisture content. d) The coefficient of kinetiic friction of iron plate on artificial soil was 0.31 to 0.41 and was comparable with that of the natural soil. e) When the pulling speed of soil bin was the 2nd forward speed of power tiller, the rpm of driving shaft of rotary was similar to that of power tiller, soil bin apparatus is indicating the good indoor tester. 3. The comparative experiment on the power requirement of prototype tine of reverse rotating rotary: According to the preliminary test of rotary tine developed with various degrees of angle between holder and edge pcint due to the kinematic analysis, comparative test between prototype rotary tine with $30 ^\circ $ and $10 ^\circ$ of it and presently being used rotary tine was carried out 2nd the results were as follows: a) The total cutting torque was low when the angle between holder and edge point was reduced. b) $\theta r$ (angle between holder and edge point) of rotary tine seemed to be one: of the factors maximizing the increase of torque. c) As the angle between holder and edge point ($\theta r$) of rotary tine was $30 ^\circ $ rather than $45 ^\circ $, the angle of rotation during cutting soil was reduced and the total cutting torque was accordingly reduced about 10%, and the reduction efficiency of total cutting torque was low when the angle between holder and edge point ($\theta r$) of rotary tine was $10 ^\circ $, which indicates that the proper angle between holder and edge point of rotary tine should be larger than $10 ^\circ $ and smaller than $30 ^\circ $ . From above results, it could be concluded that the use of the prototype rotary tine which reduced the angle between holder and edge point to $30 ^\circ $, insted of $45 ^\circ $, is disirable not only decreasing the power requirements, but also increasing the durabie hour of it. Also forward researches are needed, WIlich determine the optimum tilted angle of rotary brocket, and rearrangement of the rotary tine on the rotary boss.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.1
• /
• pp.100-106
• /
• 2018

This study was fulfilled to investigate the anatomical characteristics according to provinces. In order to compare anatomical characteristics between provinces we selected Goseong, Hongcheon, and Bonghwa as experimental sites. To use the tree rings formed at the same years we dated all tree rings by cross-dating method used in dendrochronology and the cutting years were successfully dated in 2014, 2012, and 2014 for woods from Goseong, Hongchen, and Bonghwa, respectively. Based on the cutting years tracheid lengths and widths were measured considering juvenile wood (tree rings between the pith and first 10 years), heartwood (tree rings formed between 1955 and 1964), and sapwood (tree rings formed between 2002 and 2011). According to the results about differences between tracheid lengths from three provinces, juvenile wood did not show a difference, statistically, but heartwood and sapwood showed differences as the tracheid lengths following Bonghwa, Hongcheon, and Goseong. Bongwha also showed the largest value in the trachied width among three provinces. The tracheid lengths in the radial direction increased up to around the first 20 years, and then they showed stabilized. All wood samples showed typical Korean red pine's characteristics in anatomical observation under a light microscope.

• Journal of Biosystems Engineering
• /
• v.33 no.6
• /
• pp.453-461
• /
• 2008

This study was conducted to develop a root-removed splice grafting system for cucurbitaceous vegetables, mainly watermelon and cucumber seedlings, for the seedlings factories where currently most of seedlings grafting works are carried out by manual works. The major results of the study are as follows. The dimensions of rootstocks and scions, except cotyledon width, of root- removed splice grafting of watermelon and cucumber were shown to be varied within the 2.5-fold range. The growth status of seedlings were not consistent in terms of cotyledon sprouting direction and angle which were considered as one of the important factors for in root-removed splice grafting. The grafting work of root-removed splice for grafted watermelon and cucumber could be divided by four sub-operations: seedling supplying, cutting, clipping and potting, while a part or all root of the rootstock was removed in the seedlings supplying operation. The cutting angles of the rootstock and scion were $34-45^{\circ}$ and $20-45^{\circ}$, respectively, while the stem length of the scion varied from 6 mm to 12 mm. The splices of rootstock and scion were heaped up in parallel and then fixed by a clip. It indicated that the ideal grafting system, adopting conventional grafting processes of seedlings specifications as well as conventionally manual root-removed splice grafting method, performed very well for seedlings gripping and transporting, supplying clip, clipping and discharging grafted seedlings while workers supplied seedlings to the semi-automatical system.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.43 no.5
• /
• pp.318-323
• /
• 2017

Objectives: Mandibular angle reduction or reduction genioplasty is a routine well-known facial contouring surgery that reduces the width of the lower face resulting in an oval shaped face. During the intraoral resection of the mandibular angle or chin using an oscillating saw, unexpected peripheral nerve damage including inferior alveolar nerve (IAN) damage could occur. This study analyzed cases of damaged IANs during facial contouring surgery, and asked what the basic standard of care in these medical litigation-involved cases should be. Materials and Methods: We retrospectively reviewed a total of 28 patients with IAN damage after mandibular contouring from August 2008 to July 2015. Most of the patients did not have an antipathy to medical staff because they wanted their faces to be ovoid shaped. We summarized three representative cases according to each patient's perceptions and different operation procedures under the approvement by the Institutional Review Board of Seoul National University. Results: Most of the patients did not want to receive any further operations not due to fear of an operation but because of the changes in their facial appearance. Thus, their fear may be due to a desire for a better perfect outcome, and to avoid unsolicited patient complaints related litigation. Conclusion: This article analyzed representative IAN cutting cases that occurred during mandibular contouring esthetic surgery and evaluated a questionnaire on the standard of care for the desired patient outcomes and the specialized surgeon's position with respect to legal liability.

• Journal of Periodontal and Implant Science
• /
• v.29 no.3
• /
• pp.703-715
• /
• 1999

The purpose of this study was to evaluate the degree of wear of periodontal curet's cutting edges made by three different manufacturers. In the first case of the experiment, this study was done with each new curett in the following three experiment. Twelve new double-ended No. 11/12 Gracy curettes from three different manufacturers (A, B and C) was randomly selected from our stock at first test. They were weared by wear tester with fixed pressure and limited distance. This study measured the width of worn curettes'cutting edge. The results were as follows ; 1)In 50 times experiment, this study discoverd that each manufacturer's curette was appeared with different degree of wear (p<0.01) 2)In 100 times experiment, this study result similarly to the 50 times experiment(p<0.01). 3)In 150 times experiment, the result of this study were alike as the X50 experiment and X100 experiment. In the second case of the experiment, the study was done with a curett of a manufacturer in the following three experiment. Two double-ended No. 11/12 Gracy curette from three different manufactures (A, B and C) was randomly selected from our stock at second test. 1)In 50 times experiment, this study discovered that each manufacturer's curette was appeared with different degree of wear (p<0.05). 2)In 100 times experiment, the result was same, compared with the 50 times experiment. 3)In 150 times experiment, this study also discovered that the result was same with the result of the upper two cases. In conclusion, this study discovered that the two cases of experimental were shown with a same result.

• Explosives and Blasting
• /
• v.36 no.3
• /
• pp.19-28
• /
• 2018

Locally damaged structures caused by earthquake or extraordinary external forces have been required to rapidly be dismantled because of its possibility of additional collapses. Particularly, steel frame structures were demolished by the shaped charge blasting method. Recently a research suggested a shape charge blasting technique which uses bent-shaped charge holder of copper plate and emulsion explosive charge to cut thick steel plates. This study simulated the cutting performance of the bent-shaped charge holder with considering types of explosives, thickness of copper liner and stand-off distances using LS-DYNA software. The shape charge blasting test of a 25mm thickness steel plate were used to calibrate the input parameters of the numerical models. The penetration depth and penetration width were analysed with different types of explosives, thickness of copper liner and stand-off distances.

• The Korea Journal of Herbology
• /
• v.31 no.3
• /
• pp.37-41
• /
• 2016

Objectives : The purpose of this study is to assume the size of sliced piece, daily dose and extracting Method of Rhubarb in Treatise on Cold Damage Diseases.Methods : I contrast results of recent studies with assuming results based on original text of Treatise on Cold Damage Diseases.Results : Daily dose was 6, 4 or 2 Ryang in case of cutting Rhubarb in bean-size. These prescriptions were decocted with water or sinked in boiled water. Another daily doses were large baduk-piece size 6 units and baduk-piece size 6 units in case of cutting Rhubarb in size bigger than bean. The former was used in adding to the Jisilchijasi-tang in case of constipation, the latter was used in Sihogayonggolmoryeo-tang and Jeodang-tang. The size of large baduk-piece was 2.32 cm in width, 4.64 cm in length, 4.3 g in weight, and the length and weight of baduk-piece was half of that was. Two sizes of Rhubarbs were sunk in water for 12 hours. After decocting the other ingredients, mixed Rhubarb extraction and Rhubarb, and then boiled it for 1 minute.Conclusions : From this study, daily dose of Rhubarb was 6, 4 or 2 Ryang and the 6 pieces of large baduk-piece or baduk-piece are respectively 4 or 2 Ryang. The extracting methods was decocting, sinking in boiled water for short time, sinking in water for long time and then mixing these with other decocted solution.

• Journal of the Korean Ceramic Society
• /
• v.31 no.2
• /
• pp.129-136
• /
• 1994

Si3N4 with 6w/o Y2O3 and 1.5w/o Al2O3 has been gas pressure sintered and its densification behavior and the effect of the sintering variables on the microstructure and mechanical properties were investigated. Densification rate was higher at temperature below 1775$^{\circ}C$ and between 187$0^{\circ}C$ and 195$0^{\circ}C$ than between 1775$^{\circ}C$ and 187$0^{\circ}C$. The faster densification at temperature between 187$0^{\circ}C$ and 195$0^{\circ}C$ was thought to be due to the increased amount of liquid phase resulting from the increased amount of Si3N4 dissolving in the liquid. $\beta$-Si3N4 and Y-disilicate at temperatures below 1775$^{\circ}C$, and only $\beta$-Si3N4 at 187$0^{\circ}C$ and above were detected by XRD analysis. Three different two-step schedules were employed to obtain sintered body with above 99% theoretical density and to investigate the effect of the sintering variables on the density, the microstructure and the mechanical properties of the sintered body. The sintered density did not change with the heating rate, and the microstructure became coarser as the temperature increased. The strength decreased with the width of $\beta$-Si3N4 grain, while the fracture toughness increased with the square root of it. A ceramic cutting tool made of the sintered body showed an uniform flank wear after the cutting test.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.1
• /
• pp.118-123
• /
• 2017

It is well known that water jetting is now widely used in the advanced cutting processes of polymers, metals, glass, ceramics, and composite materials because of some advantages, such as heatless and non-contacting cutting different from the laser beam machining. In this paper, we proposed the simulation model of waterjet by lengths and the inner spiral structure of the nozzle. The simulation results show that the outlet velocity of the nozzle is faster than the inlet. Furthermore, we found rapid velocity reduction after passing through the outlet. The nozzle of diameter ${\phi}500$ and length 70mm, shows the optimal fluid width and velocity distribution. Also, the nozzle with inner spiral structure shows a Gaussian distribution of velocity and this model is almost twice as fast as the model without spiral structure, within the effective standoff distance (2.5 mm). In the future, when inserting abrasive material into the waterjet, we plan to analyze the fluid flow and the particle behavior through a simulation model.

• Design & Manufacturing
• /
• v.17 no.3
• /
• pp.15-20
• /
• 2023

In the fine blanking process, which is a press operation known for producing parts with narrow clearances and high precision through the application of high pressure, die roll often occurs during the shearing process when the punch penetrates the material. This die roll phenomenon can significantly reduce the functional surface of the parts, leading to decreased product performance, strength, and fatigue life. In this research, we conducted an in-depth analysis of the factors influencing die roll in the curvature area of the fine blanking process and identified its root causes. Subsequently, we designed and experimentally verified a die roll reduction process specifically tailored for the door latch manufacturing process. Our findings indicate that die roll tends to increase as the curvature radius decreases, primarily due to the heightened bending moment resulting from reduced shape width-length. Additionally, die roll is triggered by the absorption of initial punch energy by scrap material during the early shearing phase, resulting in lower speed compared to the product area. To mitigate the occurrence of die roll, we strategically selected the Shaving process and carefully determined the shaving direction and clearance area length. Our experiments demonstrated a promising trend of up to 75% reduction in die roll when applying the Shaving process in the opposite direction of pre-cutting, with the minimum die roll observed at a clearance area length of 0.2 mm. Furthermore, we successfully implemented this approach in the production of door latch products, confirming a significant reduction in die roll. This research contributes valuable insights and practical solutions for addressing die roll issues in fine blanking processes.