• 한국정밀공학회지
• /
• 제12권11호
• /
• pp.63-73
• /
• 1995

A mechanistic force system model considering the flank wear for the face milling process has been developed. The model predicts variation of the cutting forces according to flank wear in face milling over a range of cutting conditions, cutter geometries and cutting process geometries including relative positions of cutter to workpiece and rounouts. Flycutting and multitoth cutting teste were conducted on SS41 mild steel with sintered carbide tool. In order to verify the mechanistic force model considering the flank wear of cutting tools, a series of experiments was performed with single and multitooth cutters in various cutting conditions. The results show good agreement between the predicted and measured cutting force profiles and magnitudes in time and frequency domains.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.1032-1035
• /
• 1997

The purpose of this paper is to reduce the number of cutting tests and to predict the main cutting force and the specific cutting energy. By using the SOFM neural network, the most suitable cutting test conditions has been found. As a result, the number of cutting tests has been reduced to one-third. And by using MLP neural network and regression analysis, the main cutting force and specific cutting energy has been predicted. Predicted values of main cutting force and specific cutting energy are well concide with the measured ones.

• 한국정밀공학회지
• /
• 제14권2호
• /
• pp.169-177
• /
• 1997

In this study, investigated are the effects of tool rake angles and the change of cutting conditions on the specific cutting pressure in face milling. The cutting force in face milling is predicted from the double cutting edge model in3-dimensional cutting. Conventional specific cutting pressure model is modified by considering the variation of tool rake angles. Effectiveness of the modified cutting force model is verified by the experiments using special face milling cutters with different cutter pockets and various rake angles. From the comparison of the presented model and the specific cutting pressure, it is shown that the axial force can be predicted by the tangential force, radial force and geometric conditions. Also, the rela- tionship between specific cutting pressure and cutting conditions including feedrate, cutting velocity and depth of cut is studied.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2004년도 추계학술대회 논문집
• /
• pp.237-240
• /
• 2004

Indexable end mills, which consist of inserts and cutter body, have been widely used in roughing of parts in the mold industry. The geometry and distribution of inserts on cutter body are determined by application. This paper proposes analytical cutting force model for indexable flat end-milling process. Developed cutting force model uses the cutting-condition-independent cutting force coefficients and considers runout, cutter deflection and size effect for the accurate cutting force prediction. Unlike solid type endmill, the tool geometry of indexable endmill is variable according to the axial position due to the geometry and distribution of inserts on the cutter body. Thus, adaptive algorithm that calculates tool geometry data at arbitrary axial position was developed. Then number of flute, angular position of flute, and uncutchip thickness are calculated. Finally, presented model was validated through some experiments with aluminum workpiece.

• 한국정밀공학회지
• /
• 제14권4호
• /
• pp.38-45
• /
• 1997

A new dynamic model for the cutting process inb the end milling process is developed. This model, which describes the dynamic response of the end mill, the chip load geometry including tool runout, the dependence of the cutting forces on the chip load, is used to predict the dynamic cutting force during the end milling process. In order to predict accurately cutting forces and tool vibration, the model which uses instantaneous specific cutting force, inclueds both regenerative effect and penetration effect, The model is verified through comparisons of model predicted cutting force with measured cutting force obtained from machining experiments.

• 한국정밀공학회지
• /
• 제3권4호
• /
• pp.30-42
• /
• 1986

On the analysis of cutting mechanics in orthogonal cutting, each cutting force component can be predicted. By adding the flank face wear term to the prediction equation for cutting force components, complete equations are obtained. Using these equations, it is shown that cutting force components are increased linearly as flank face wear land is developed, in theory and experiment. By making non-dimensional term ie. Fv/Fc, the width of variation of output signal Fv/Fc is greately decreased compared with each cutting force component as cutting condition is varied. Among these conditions, the variation of chip width in the range of more than 1mm and that of cutting velocity have little effect on the output signal Fv/Fc, that of Flank face werr land can be detected without difficulty.

• 한국정밀공학회지
• /
• 제3권2호
• /
• pp.91-101
• /
• 1986

This paper deals with the effect of static and dynamic cuttig force and the behaviour of drill life in drilling process. The experiments are performed with cemented carbide drills and high speed steel drills of 10mm in diameter and in an annealed SM45C. The conclusions are as follows (1) Dynamic cutting force is varied with the dept of hole. (2) Dynamic cutting forces of torque and thrust are increase with the increase in feed and cutting speed. (3) Chipping influence the dynamic cutting force of thrust than torque, and in the case of thrust, the amplitude is 3-7 times large than ordinary cutting state. (4) Prediction of drill life can be obtained from more easily the amplitude of static cutting force than that of dynamic cutting force.

• 한국기계가공학회지
• /
• 제13권2호
• /
• pp.108-116
• /
• 2014

Considering the run-out effect and cutting force coefficients, the cutting force profile of half immersion end-milling was analyzed in detail. The effects of three specific cutting-force coefficients and three edge-force coefficients are verified. Through a detailed investigation, it is proved that the radial cutting force coefficients and are the major factors which increase the cutting forces Fx and Fy in end-milling. However, the axial cutting force coefficients have no influence on the force Fx and Fy changes in end-milling. Also, the analyzed end-milling force model shows good consistency with the actual measured force with regard to Fx and Fy. Thus, this model can be used for the prediction of the force history in end-milling with run-out, and it incurs a different force history with different start and exit immersion angles as well as holding effects.

• 한국정밀공학회지
• /
• 제27권9호
• /
• pp.86-93
• /
• 2010

Any relative deformation between the cutting tool and the workpiece at the machining point, results directly in form and dimensional errors. The source of relative deformations between the cutting tool and the workpiece at the contact point may be due to thermal, weight, and cutting forces. Thermal and weight deformations can be measured at various positions of the machine tool and stored in the compensation registers of the CNC unit and compensated the errors during machining. However, the cutting force induced errors are difficult to compensate because estimation of cutting forces are difficult. To minimize the error induced by cutting forces, it is important to improve the machining accuracy. This paper presents the pre-calculated method of form error induced by cutting forces. In order to estimate cutting forces, Isakov method is used and the method is verified by comparing with the experimental results. In order to this, a cylindrical-outer-diameter turning experiments are carried out according to cutting conditions.

• 한국정밀공학회지
• /
• 제15권2호
• /
• pp.146-153
• /
• 1998

NC machines with 4 or 5 axes are capable of various tool approach motions, which makes interference-free and high machinablity machining possible. This paper deals with how to integrate these two advantages (interference-free and high machinability machining) in multi-axes NC machining with a ball-end mill. Feasible tool approach region at a point on a surface is first computed, then among which an approach direction is determined so as to minimize the cutting force required. Tool and spindle volumes are considered in computing the feasible tool approach region, and the computing time is improved by trans-forming surface patches into minimal enclosing spheres. A cutting force prediction model is used for estimating the cutting force. The algorithm is developed so as to be applied to 4- or 5-axes NC machining in common.