• Geomechanics and Engineering
• /
• 제38권4호
• /
• pp.367-380
• /
• 2024

In this study, a prediction model for the cutting force evolution in brittle rocks was developed. This model is based on indentation tests using a conical pick at a cutting depth of 9 mm. The behavior of the indentation mechanism was analyzed in three phases by using Evans' cutting mode. The peak values in the force history identified these phases. The variation in the local strength of the rock caused a large offset in the model prediction of chipping. Regression analyses showed that there is a strong power relationship between the upper bound of the cutting force along with chipping and depth of cut. The slope of the three crushing phases has been found to increase sequentially (α₁<α₂<α₃). In addition, a positive correlation existed between the Schmidt hardness and brittleness index that affects the lower and upper bounds of chipping. Consequently, the results clearly demonstrate that the new model can reasonably predict the evolution of the cutting force based on experimental data. These results would be beneficial for engineers to design and select the optimum excavation machine to reduce mechanical vibration and enhance cutting efficiency.

• 한국생산제조학회지
• /
• 제20권3호
• /
• pp.225-231
• /
• 2011

In this paper, a new end-milling force modelling technique was suggested by considering runout, and its result was compared with real measured force. The specific cutting force is the multiplication of cutting force coefficient and uncut chip thickness. This parameter was used for experimental modelling and prediction of theoretical force. These coefficients, which can be obtained by fitting measured average forces in several conditions, were used for the formulation of theoretical force. The mechanism of end-milling force with runout was developed in this research and its result was verified by comparing the fluctuating theoretical force and its measured one. The fluctuation of force was incurred by a geometric shape of workpiece and its runout in holding. The result of suggested force considering runout shows a good consistency with measured one. So this modelling method can be used effectively for a prediction of end-milling force with runout effect.

• 한국공작기계학회논문집
• /
• 제13권4호
• /
• pp.9-15
• /
• 2004

A reasonable analysis of cutting force in end milling may give much advantage to improvement of productivity and cutting tool life. In order to analyze cutting force, the cutting dynamics was modelled mathematically by using chip load, cutting geometry, and the relationship between cutting forces and the chip load. The specific cutting constants of the cutting dynamics model were obtained by average cutting forces, tool diameter, cutting speed, feed, axial depth, and radial depth of cut. The model is verified through comparisons of model predicted cutting forces with measured cutting forces obtained from machining experiments. The results showed good agreement and from that we could predict reasonably the cutting forces in end milling.

• 한국공작기계학회논문집
• /
• 제11권2호
• /
• pp.1-8
• /
• 2002

Cutting force is obtained as a sum of chip removing force and ploughing force. Chip removing force is estimated by multiplying specific cutting pressure by cutting area. Since ploughing force is caused from dullness of a tool, its magnitude is constant if depth of cut is bigger than a certain value. Using the linearity of chip removing force to cutting area and the constancy of ploughing force regardless of depth of cut which is over a certain limit each force is separated from measured cutting force and used to establish cutting force model. New rotation matrix to convert the measured cutting force in reference axes into the forces in cutter axes is obtained by considering that tool angles are projected angles from cutter axes to reference axes.. Spindle tilt is also considered far the model. The predicted cutting force estimated from the model is in good agreement with the measured force.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.788-793
• /
• 1997

The surface,generated by end milling operation, is deteriorated by tool runout,vibration,friction,tool deflection, etc. In many source,deflection of tool affects to surfave accuracy. To develop a surface accracy model,method for the prediction of the topography of machined surfaces has been developed based on models of machine tool kinematics and cutting tool geometry. This model accounts for not only the ideal geometrical surface, but also the deflection of tool resulted in cutting force. For the more accurate prediction of cutting force,flexible end mill model is used to simulate cutting process. Compute simu;ation have shown the feasibility of the surface generation system.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 추계학술대회 논문집
• /
• pp.725-726
• /
• 2008

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.394-397
• /
• 2004

This paper presents a simple analytic method using 2D simulation program for predications of cutting force and machining temperature in dry type milling process. And also, comparison of cutting force and machining temperature obtained from experiment and simulation work is accomplished to distinguish of suitability.

• 한국생산제조학회지
• /
• 제22권6호
• /
• pp.1003-1009
• /
• 2013

This paper presents a simple procedure to obtain the instantaneous cutting force constants needed to predict milling forces. Cutting force data measured in a series of slot milling tests were used to determine the cutting force constants at different feed rates. The values of the cutting force constants were determined directly at the tool rotation angle that maximized the uncut chip thickness. Then, the instantaneous cutting force constant was obtained as a function of the instantaneous uncut chip thickness. This approach can greatly enhance the accuracy of the mechanistic cutting force model for end milling. In addition, the influences of several cutting parameters on the cutting forces, such as the tool helix angle and axial depth of cut, were discussed.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.485-489
• /
• 2004

Cutting force is important to understand cutting process in milling. To measure cutting force, tool dynamometer is widely used but it is hard to apply in workshop condition. Cutting force measurement which doesn't affect cutting process is needed. Using relations between cutting force and spindle displacement, cutting force can be predicted. Cylindrical capacitive sensor was used to measure spindle displacement during cutting. And signals from tool dynamometer collected to compare with spindle displacement. The result shows spindle displacement has a linear relation with cutting force. Using this result, a simple method to predict cutting force could be applied at workshop condition.

• 한국정밀공학회지
• /
• 제15권5호
• /
• pp.145-152
• /
• 1998

In this research, in order to predict the cutting force using a mechanistic model, specific cutting force was firstly obtained through the cutting experiments. Band sawing process is similar to a milling, that is multi-point cutting. Therefore it is not easy matter to evaluate specific cutting force. Thus, the thickness of workpiec was made smaller than one pitch of the saw in terms of fly cutting in the face milling process. Then the cutting force was predicted by analyzing the geometric shape of a saw tooth The tooth shape used in the research was raker set style that was generally used in band sawing. And a set of teeth is comprised of three teeth, those are ranked as left, straight and right. The mechanistic model was developed in this study considered those shapes of each tooth. From the validation experiments, the predicted cutting forces coincided well with the measured ones. Therefore the predicted cutting forces can be used for the adaptive control of saw engaging feed rate in the band sawing.