• 한국산학기술학회논문지
• /
• 제20권12호
• /
• pp.390-397
• /
• 2019

현대 제조 공업이 고효율, 고정밀도와 경제적인 방향으로 발전 하면서 금속을 절단하는 띠톱 기계는 이미 철강, 기계, 자동차, 조선, 석유, 광산, 항공 우주 등 다양한 영역에서 광범위 하게 활용 되고 있다. 하지만 기존의 띠톱 기계들은 경험적으로 설계 되어져 왔으며 따라서 낮은 수명, 톱질 동작 상태에서 낮은 정밀도 및 저효율을 문제와 높은 제조원가 문제를 가지고 있다. 본 논문에서는 띠톱의 역학적 해석을 통해 띠톱 톱대의 설계 파라미터를 개선하는 방법을 제시 하였다. 실제로 빈번하게 사용 되고 있는 띠톱 기계를 모델링 하여 응력 분석, 피로해석을 시행 하였으며 이에 따라 톱대의 상세한 설계 파라미터를 도출 하였다. 그 결과 피로 강도가 피로 요구 사항을 만족 시키고 띠톱 기계의 정밀도와 효율이 크게 향상 되는 것을 확인할 수 있었다.

• Steel and Composite Structures
• /
• 제34권5호
• /
• pp.681-698
• /
• 2020

The paper addresses contribution to the modeling and optimization of major machinability parameters (cutting force, surface roughness, and tool wear) in finish dry hard turning (FDHT) for machinability evaluation of hardened AISI grade die steel D₃ with PVD-TiN coated (Al₂O₃-TiCN) mixed ceramic tool insert. The turning trials are performed based on Taguchi's L₁₈ orthogonal array design of experiments for the development of regression model as well as adequate model prediction by considering tool approach angle, nose radius, cutting speed, feed rate, and depth of cut as major machining parameters. The models or correlations are developed by employing multiple regression analysis (MRA). In addition, statistical technique (response surface methodology) followed by computational approaches (genetic algorithm and particle swarm optimization) have been employed for multiple response optimization. Thereafter, the effectiveness of proposed three (RSM, GA, PSO) optimization techniques are evaluated by confirmation test and subsequently the best optimization results have been used for estimation of energy consumption which includes savings of carbon footprint towards green machining and for tool life estimation followed by cost analysis to justify the economic feasibility of PVD-TiN coated Al₂O₃+TiCN mixed ceramic tool in FDHT operation. Finally, estimation of energy savings, economic analysis, and sustainability assessment are performed by employing carbon footprint analysis, Gilbert approach, and Pugh matrix, respectively. Novelty aspects, the present work: (i) contributes to practical industrial application of finish hard turning for the shaft and die makers to select the optimum cutting conditions in a range of hardness of 45-60 HRC, (ii) demonstrates the replacement of expensive, time-consuming conventional cylindrical grinding process and proposes the alternative of costlier CBN tool by utilizing ceramic tool in hard turning processes considering technological, economical and ecological aspects, which are helpful and efficient from industrial point of view, (iii) provides environment friendliness, cleaner production for machining of hardened steels, (iv) helps to improve the desirable machinability characteristics, and (v) serves as a knowledge for the development of a common language for sustainable manufacturing in both research field and industrial practice.

• 문화기술의 융합
• /
• 제8권2호
• /
• pp.367-372
• /
• 2022

최근 뉴노멀시대가 도래하면서 실감형 기술과 언택트 기술은 사회적 관심을 받고 있다. 하지만 헤어 스타일링 분야는 헤어 시뮬레이션을 중점으로 헤어 자체의 연출이나, 개별적인 움직임, 모델링에 초점을 두고 있다. 시대적 요구와 개선된 실습환경 조성을 위해 본 연구에서는 비대면 헤어 스타일링 VR 시스템을 제안하였다. 이론 고찰에서는 기존 헤어 컷 연구 사례에 대해 조사하였다. 기존 헤어 컷 관련 그래픽스 연구는 주로 힘 기반 피드백 위주의 연구이다. 본 논문에서 주장하는 가상환경에서 인터랙티브한 헤어 컷 작업에 대한 연구는 아직 이루어지고 있지 않다. 본 연구에서는 미용에 필요한 동작을 핑거 트래킹이 가능한 VR 컨트롤러에서 미용도구 선택, 자르기, 회전 등이 가능하도록 하였으며 비대면 협업 환경으로 구축하였다. 연구 결과로서, 정확한 헤어 절단 작업을 위해 소지걸이 애니메이션에 따른 핑거 트래킹과 가위의 움직임이 위치 보정에 따른 동기화 작업의 결과와 다중 사용자 기반의 가상 협업 환경에서의 실시간 인터랙티브 헤어 컷 작업을 실험하였다, 비대면 상황에서 헤어 스타일링에 필요한 커트동작에 관한 학습이 가능하게 되었으며 교수자와 학습자는 VR HMD 내장 마이크와 Photon Voice로 상호 간의 의사소통이 가능하게 되었다.

• 동력기계공학회지
• /
• 제13권6호
• /
• pp.95-101
• /
• 2009

The generator for gas turbine power generation consists of the rotor which generates magnetic field, the winding coil which is the path for the field current and the wedge and retaining ring which prevents the radial movement of the coil. Relatively severe deformation was observed at the coil end section during the inspection of the generator for peaking-load operation, and the thermal-electricity and the centrifugal force were evaluated by the simple modeling of the windings to find the cause. But the simulation stress was not sufficient to induce the coil plastic deformation. The analysis result seems to be applicable to the base-load generators which runs continuously without shut down up to a year, but there had been more deformation than simulated for the generator which is started up and shut down frequently. The cause of the coil deformation was the restriction of the expansion and shrinkage. The restriction occurs when the winding coil shrinks, and the stress overwhelms the yield stress and cause the plastic deformation. The deformation is accumulated during the start-ups and shut-downs and the thermal growth occurs. The factors which induce the coil restriction during the expansion and shrinkage should be reduced to prevent the unallowable deformation. The resolutions are cutting off the field current earlier during the generator shut-down, modifying the coil end section to remove the stress concentration and making the insulation plate inserted between the coil end section and the retaining ring have the constant thickness.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제9권3호
• /
• pp.315-325
• /
• 2017

The design dimension may not be satisfactory at the final stage due to the welding during the assembly stage, leading to cutting or adding the components in large structure constructions. The productivity is depend on accuracy of the welding quality especially at assembly stage. Therefore, it is of utmost importance to decide the component dimension during each assembly stage considering the above situations during the designing stage by exactly predicting welding deformation before the welding is done. Further, if the system that predicts whether welding deformation is equipped, it is possible to take measures to reduce deformation through FE analysis, helping in saving time for correcting work by arresting the parts which are prone to having welding deformation. For the FE analysis to predict the deformation of a large steel structure, calculation time, modeling, constraints in each assembly stage and critical welding length have to be considered. In case of fillet welding deformation, around 300 mm is sufficient as a critical welding length of the specimen as proposed by the existing researches. However, the critical length in case of butt welding is around 1000 mm, which is far longer than that suggested in the existing researches. For the external constraint, which occurs as the geometry of structure is changed according to the assembly stage, constraint factor is drawn from the elastic FE analysis and test results, and the magnitude of equivalent force according to constraint is decided. The comparison study for the elastic FE analysis result and measurement for the large steel structure based on the above results reveals that the analysis results are in the range of 80-118% against measurement values, both matching each other well. Further, the deformation of fillet welding in the main plate among the total block occupies 66-89%, making welding deformation in the main plate far larger than the welding deformation in the longitudinal and transverse girders.