• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.734-739
• /
• 2003

Many types of smart materials and control laws are available to actively adjust the structure from various external disturbances. Usually, a certain type of control laws to activate a specific smart material is well established, but the effectiveness of the control scheme is limited by the choice of the smart materials and the responses of the structure. ER fluid is adequate to provide relatively large control force, on the other hand, the PZT patches are suitable to provide small but arbitrary control forces at any point along the structure. It was found that active vibration control mechanism using ER fluid failed to suppress the excitation off the resonant frequency with changed structural characteristics along the frequency response function of the closed loop of the control system. To compensate this additional peak of the closed loop system, PPF control using PZT as an actuator is added to construct a hybrid controller.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.5 no.3
• /
• pp.65-70
• /
• 2006

The AWJM(Abrasive Water-jet Machining) technology is one of the cutting technologies, which can cut various materials with 2 or 3 times of the speed of sound. In this study, processing conditions such as jet-pressure, cutting speed, orifice diameter and stand-off distance, are used by following the design of experiments with 3 levels. Al6061 material which is normally applied on the field, is applied. Through the S/N ratio analysis with measured values, the optimization value of processing conditions to minimize the surface roughness and taper value is obtained. The order of significance is as follows; jet pressure, cutting speed, abrasive mixing ratio, orifice diameter and stand-off distance. RSM(Response Surface Method) is applied to find the optimal processing conditions to minimize both the surface roughness and the taper value by using jet pressure, cutting speed and abrasive mixing ratio.

• Journal of the Korean GEO-environmental Society
• /
• v.11 no.12
• /
• pp.13-18
• /
• 2010

This study was made on the fact that the environmental impact and durability of the recently developed alkali silicasol chemical grout material. The grout material used for this study was designed to understand its environmental impact and durability through the SEM, chemical resistance test, leaching test, permeability test. In order to compare with the engineering characteristics regarding alkali silicasol grout material and sodium silicate grout material. As a result of SEM, the surface and internal tissues of alkali silicasol grout material could be identified to be denser than those of sodium silicate. As a result of leaching test the adaptability was identified as grout material as it had proved to be an ecological material owing to the total amount of the element to be leached being extremely little. As a result of permeability test it is judged that it is possible to apply the silicasol to the site in the place requiring the water cut-off as the silicasol.

• Transactions on Electrical and Electronic Materials
• /
• v.7 no.5
• /
• pp.224-229
• /
• 2006

Many studies have been done on the application of residual charge measurement in cable degradation diagnosis. In this paper, the behavior of residual charges measured with water-tree degraded XLPE sheets and cable are discussed. At charge injection process, the charge is injected by applying dc voltage as a conventional method, suddenly cut-off ac voltage or impulse voltage. Therefore the residual charge is influenced by the applying process. At charge release process, transient dc current flows when applying ac high voltage and also ac high voltage superimposed to dc low voltage. From the results, new diagnosis method is suggested.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.10a
• /
• pp.190-195
• /
• 1997

The requirement of precision products about difficult-to-cut materials such as Cu and Aluminum alloy is becoming more and more. Because of soft materials, the exist narrow groves on surface are difficult to gotten off even on the polishing stage. It has been proved that Magnetic-Electrolytic-Abrasive Polishing (MEAP) is a efficient method to resolve this problem by using the nonwoven-abrasive pads together [1, 2]. In this study, through the experiments, their machining properties of newly developer polishing material of SiC, Al2O3 and diamond nonwoven abrasive pads have been proved. Through the experiments, the optimal machining conditions on larger cylinder shape workpiece of Cu and Aluminium alloy have been found, through the Taguchi[3] method the optimal machining conditions can be selected.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.855-858
• /
• 2001

The single transformer appeared the electro-magnetic force must be constructed to support it. it must construct the single transformer to supporting the electro-magnetic force appeared by the cut-off current. the problem is that the electro-magnetic occurs the modification of the single transformer and an serious accident. In the case of the molding-transformer, the part of the molding cast used in the construction occurs the crack, because of the strong force. therefore, in this paper, the molding material used in the molding-transformer is settled by comparing the results from commercial soft ware of F.E.M and a out-equipment circuit.

• Electrical & Electronic Materials
• /
• v.8 no.4
• /
• pp.443-450
• /
• 1995

A directional coupler which on the X-cut $LiNbO_3$ substrate is fabricated by using proton exchange method and self-aligned method. After proton exchange process, the waveguide is formed by annealing process. The relation ship between refractive index change of waveguide and maximum output was studied along with the annealing time. A self-aligned method was used to simplify the fabrication process of the waveguide and to maximize the efficiency of electric field. The on-off state of modulator has been observered with the switching of the directional coupler by the electric field effect and also the switching voltage of the directional coupler has been measured with 8.0 [V].

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.883-886
• /
• 2001

The mechanical properties such as the Young's modulus, damping ratio, vibration mode and hardness of the disk materials heat-treated under various conditions are measured, and the relations between there properties and the cutting characteristics such as early tip fracture are examined. The results obtained from this study are as follows. The circular saw with the V-Cr added disk has higher young's modulus and damping ratio than the saw with STC5 disk, preventing the early fracture of tungsten carbide due to the above properties. The circular saw with the disk which is subjected to the heat treatment at the quenching temperature of $830^{\circ}C$ and at the temperature of $550^{\circ}C$ have the best tool life and surface roughness.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.546-551
• /
• 1997

New typology of failure mechanisms for uniform compression fields are presented based on the classical theory of plasticity, in particular th normality rule, and the limit theorem. The concrete is assumed as a rigid-perfectly plastic material obeying the modified Coulomb failure criteria with zero tension cut-off. The failure mechanisms are capable of explaining flexural types of crushing failure in uniaxial uniform compression stress fields which are called struts in truss models. The failure mechanisms consist of sliding failure along straight failure lines or hyperbolic failure curves and rigid body rotation. The failure mechanisms involving straight failure lines are explained by constant strain expansion in the first principal direction and rigid body rotation motion. The failure mechanisms presented are applied to the explanation of bond failure of bar combined with concrete crushing failure and flexural crushing failure of concrete.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.9
• /
• pp.48-55
• /
• 2005

In this paper, wrinkling behavior for anisotropic membrane was studied. The analyses were done by using membrane elements and the wrinkling was accounted for by the penalty parameter modified material modeling which was implemented to ABAQUS as a user subroutine. The wrinkle model was applied to corner-loaded square membranes in which the effect of the diameter of steel pin, edge cut-off length and the magnitude of shear moduli on the wrinkling was investigated.