• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.3
• /
• pp.209-214
• /
• 1995

Abstract 0.2 wt % $Fe_2O_3$ doped $SrTiO_3$ single crystals were grown by floating zone method in air and Nz atmosphere, respectively. The growth rate was fixed at 5 mm/hr and rotation speed was maintained at 30 rpm. As - grown crystals were cut perpendicular to its growth direction and then, annealed at 900, 1000 and $1100^{\circ}C$ for 2 hours in Nz atmosphere. Resistivities of each samples were measured and then converted into conductivities. By using these conductivity values, the activation energies were calculated and by means of the calculated activation energies, mechanism which contribute to increasing the electrical conductivity were investigated.

• Journal of Environmental Health Sciences
• /
• v.29 no.3
• /
• pp.91-96
• /
• 2003

This study was intended as an investigation of characteristics of background site atmospheric respirable particulate matters(RPM), and fine particles(<2.5 ${\mu}{\textrm}{m}$). The particle size distributions during the phenomenon of Yellow Sand(YS) occurs from April, 2001. Atmospheric aerosol particulate matter was directly collected on the Jeju island between 1 to 30, April, 2001 using an eight-stage cascade impacter(particle size range: 0.43-11 ${\mu}{\textrm}{m}$), and cyclone separator(cut size: 2.5, 10 ${\mu}{\textrm}{m}$). The episode of YS observed in background monitoring site, Kosan and appeared 2 times at sampling period. The mass concentrations of fine and coarse particles for YS episode were 34.2 and 59.6 $\mu\textrm{g}$/㎥, respectively, which were significantly increased amounts compared to 13.3 and 13.0 $\mu\textrm{g}$/㎥ for NonYS(NYS). Most size distributions had two peaks, one at 0.43∼.65 ${\mu}{\textrm}{m}$ and the other at 3.3${\mu}{\textrm}{m}$4.7 ${\mu}{\textrm}{m}$. The result of analysis of water-soluble ion component indicated that sulfate was mainly ion component, but nitrate and calcium ion was significantly increased at the YS episode.

• Journal of Animal Environmental Science
• /
• v.19 no.1
• /
• pp.9-18
• /
• 2013

Currently, there was no producing system of TMR for pig feeding in Korea. In this study, we examined unrolling, cutting, and softening for the round bale silage. We designed and developed the prototype system of round bale silage for pig feeding. Unroll method were lower chain conveying and upper belt conveying which includes an hydraulic vertical fodder knife. Gathering and cutting method were rotating auger and flywheel which have 10 cutters, input roller of 280 rpm, and cutter rotating speed of 1,750 rpm. Softening device was rotating hammer in inclined cylinder adjustable to $25^{\circ}C$ and rotating speed up to 1,300 rpm. The prototype system was integrated working for unrolling, cutting, and softening. We found that when the round bale silage in unrolling apparatus cut length of 20 cm to input cutting apparatus, the cutting performance was well in continuous working up to input rate of 1,000 kg/h, the softening apparatus was working well.

• Journal of Biosystems Engineering
• /
• v.42 no.2
• /
• pp.80-85
• /
• 2017

Purpose: In this study, we attempted to analyze, by using a high-speed camera, the cutting shape as a function of cutting speed and feed rate. We compared the differences in cutting shape between domestic and foreign combines. Methods: Experiments were performed using plastic straws, and the results of two combine cutting blades, one from the Daedong Industry and one from Kuboda, were compared. The quality and performances of cutting were measured at three cutting positions: center and 68 cm to the left and right of the center. The feed rates were 0.6 m/s, 1.1 m/s, 1.6 m/s, and the cutting speeds were 600 RPM, 990 RPM, 1,380 RPM. For each speed, the cutting shape was measured three times, and the entire procedure was also repeated three times. Results: In the experiments, the domestic cutting blade achieved better results than the Japanese cutting blade. These results were obtained by studying the combination of feed rate and cutting speed, with the domestic combine attaining approximately 80% performance of the Japanese combine. We believe that additional data analysis is required, obtained from field experiments. Conclusions: The domestic cutting knives achieved better results than the Japanese cutting knives. These results are estimated from experiments conducted with different feed rates and cutting speeds; an in-depth analysis will require experiments in the real field with actual combines and a combination of multiple variables. Repeating the investigation on the length differences, broken and cut angle with various combinations of feed rate and cutting speed, will surely help to find the optimal cutting speed.

• Environmental Engineering Research
• /
• v.24 no.2
• /
• pp.263-270
• /
• 2019

Palm oil mill effluent (POME) is the largest pollutant discharged into the rivers of Malaysia. Thus UF membrane study was conducted to investigate the effect of pressure and stirring speed on performance of POME treatment and fouling of membrane. Two types of membrane polyethersulfone (PES) and regenerated cellulose (RC) with molecular weight cut-off (MWCO) 5 and 10 kDa were used in this study. Results showed that, as pressure increased, fouling increased however permeate quality improved, the best pressure was 1.0 bar, where the fouling was not too high and produce good permeate quality. As stirring speed increased, fouling reduced and permeate quality improved, however, when stirring speed increased from 600 rpm to 800 rpm, there was no significant improvement on the permeate quality. Therefore, the best condition was at 1.0 bar and 600 rpm. PES membrane with MWCO 5 kDa showed the best permeate quality, even fouling slightly higher than RC membrane. The permeate quality obtained were analyzed in term of dissolved solid, turbidity, suspended solid, biological oxygen demand ($BOD_5$) and chemical oxygen demand (COD) were 538 mg/L, 1.02 NTU, < 25 mg/L, 27.7 mg/L and 62.8 mg/L, respectively with dominant type of fouling is cake resistance. Thus, it can be concluded water reuse standard was successfully achieved in terms of $BOD_5$ and suspended solid.

• Design & Manufacturing
• /
• v.11 no.1
• /
• pp.50-54
• /
• 2017

In this study, researches were conducted as follows. First, as the basic experiment, the cutting speed, feedrate, and the depth of cut were set as the process parameters, and by setting the surface roughness as the factor of measurement for each of the combinations, and the analysis about cutting tendency of the material was conducted by proceeding the turning process of Co-Cr-Mo alloy. Second, by setting the feature of the surface roughness according to the 'turning processing condition' that was confirmed in the previous experiment, and by applying the Taguchi Method, the conditions that influence the features of the surface roughness according to the 'turning processing condition' of Co-Cr-Mo was analyzed, and also by measuring the surface roughness according to each of the 'cutting conditions', the optimal processing condition was generated. As the result of analysis, it was possible to understand that the factor that mostly affects the surface roughness was the cutting speed, followed by the dept of cutting and transfer speed, and as for the optimal processing condition, it was possible to find that the cutting speed was 5,000rpm, and the depth of cut was 0.1mm, and the feedrate was 0.003mm/rev, and the value of the surface roughness at this point is $0.197{\mu}m$.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.4_2
• /
• pp.605-613
• /
• 2023

The multi-axis combined machining technology has enabled combined machining, which was difficult. However, the reality is that manufacturing costs are rising due to expensive equipment and there is a shortage of machine operation engineers. The purpose of this research is to present the optimum cutting conditions for the surface roughness when processing the inner diameter of SUS440C, which is an egg material, using a CNC automatic lathe. As a result of measuring the surface roughness, dry machining was the best at R_a0.481㎛ at a spindle speed of 4,000rpm, a feed rate of 0.05rev/min, and a cutting depth of 0.3mm. In wet machining, the highest value was R_a0.317 at a spindle speed of 2,000 rpm, a feed rate of 0.05 rev/min, and a cutting depth of 0.2 mm. The lower the feed rate, the better surface roughness appears. It was found that the feed rate had more influence than the number of revolutions and depth of cut.

• Korean Journal of Food Science and Technology
• /
• v.28 no.3
• /
• pp.506-513
• /
• 1996

Soybean hull was microparticulated at cut-off wheel speed of 9,000 rpm and air-classified into fine and coarse fraction at air classifying wheel speeds (ACWS) of 10.000, 15,000 and 20,000 rpm. respectively. Proximate analysis of the coarse and fine fractions of the microparticulated/air-classified soybean hull showed that ash, protein and lipid were enriched in the coarse fractions and carbohydrates in the fine fraction. Dietary fiber were enriched in coarse fractions and dietary fiber and dietary fiber content increased with decreasing ACWS. Mean particle size of fine fractions ranged from $3.1{\mu}m\;to\;5.5{\mu}m$ that of coarse fractions ranged from $9.9{\mu}m\;to\;20.0{\mu}m$ and both increased with decreasing ACWS. The particles were mostly oval-shaped regardless of the fractions. Generally the fraction of low ACWS showed higher viscosity. In water holding capacity, oil absorption and emulsion capacity, there was significant difference between coarse and fine fractions while there was no significant difference as a function of different ACWS. Oil absorption of flying batter was decreased significantly in the fraction of ACWS 15,000. when cakes and cooking were prepared partially substituted with soybean hull fraction, there was no significant changes on their physical and sensory properties up to 10% substitution.

• Asian Journal of Turfgrass Science
• /
• v.18 no.1
• /
• pp.29-36
• /
• 2004

The efficient refinement of seed is required to reduce the cost and labor input in artificial propagation of wild plant. This study was carried out to develop methods for collecting and refining tiny seeds from wild plants. For obtaining Phragmites communis seeds, the inflorescence was cut into small fragments using a Straw Cutter and subsequently detached pappus hairs from seed coat by Hammer Mill. The primary refined seeds were passed 1.0 mm sieve. The screened seeds were subjected to Seed Blower with wind speed of 0.25 mㆍsec-1 to collected intact and well-ripen seeds. The seeds of Imperata cylindrica were refined as follows. Inflorescences were cut using a Straw Cutter first. The pappus was removed from cut fragments using a Hammer Mill and subsequently subjected to Seed Scarifier at 500rpm for 60 sec. for further separation. The separated seeds were passed 1.0 mm screen and collected after blowing with Seed Blower of wind speed of 0.15 mㆍsec-1. When the amount of seed was too little to refine with Seed Scarifier and Blower, the procedure was slightly modified from the procedure described above. The crude seed mixture obtained from Hammer Mill step was hand-refined roughly and then immersed into cone. (95%) sulfuric acid for 2 min. and collected floating portion after dilution of sulfuric acid solution 100 times with tap water. The collected seeds were dried and passed 0.149 mm sieve. During seed refining process using mechanical or sulfuric acid treatments, a small portion of damaged seed were evolved, however, the amount was not noticeable as compared to the total amount of collected seeds. Because the germination percentages between hand-refined seeds and seeds refined by above methods were not statistically different, the developed procedures for refining tiny seed of wild plants are helpful to reduce the cost and labor input in artificial propagation of two species.

• Journal of agriculture & life science
• /
• v.51 no.2
• /
• pp.165-173
• /
• 2017

To evaluate performance of the experimental pick-up type pulse crop harvester for harvesting sprout bean, its pick-up and discharging grain loss ratios, grain quality such as whole grain ratio, damaged grain ratio, unthreshed grain, and foreign material ratio in grain tank, germination rate of threshed grain, and theoretical field capacity of the harvester were analyzed according to engine speeds of 2000, 2400 and 2800 rpm and harvesting speeds of 0.6, 1.0 and 1.4 m/s. It is considered that the harvester showed optimum performance at the engine speed of 2800 rpm and the harvesting speed of 1.0 m/s, and then average pick-up grain loss ratio of 2.7%, discharging grain loss ratio of 0.5%, whole grain ratio of 99.3%, damaged grain ratio of 0.2%, unthreshed grain ratio of 0.0%, foreign material ratio of 0.2%, and germination rate at 8 days after seeding of 72.8% were shown. It is considered that the harvester has lower grain loss and higher grain quality than the imported bean combines. And also as it could harvest 3 rows of cut and dried sprout bean crop width of which was about 2 m, its effective field capacity was estimated for about 50 a/h.