• Nuclear Engineering and Technology
• /
• v.48 no.6
• /
• pp.1330-1337
• /
• 2016

A visualization test of the fuel-coolant interaction in the Test for Real cOrium Interaction with water (TROI) test facility was carried out. To experimentally simulate the In-Vessel corium Retention (IVR)- External Reactor Vessel Cooling (ERVC) conditions, prototypic corium was released directly into the coolant water without a free fall in a gas phase before making contact with the coolant. Corium (34.39 kg) consisting of uranium oxide and zirconium oxide with a weight ratio of 8:2 was superheated, and 22.54 kg of the 34.39 kg corium was passed through water contained in a transparent interaction vessel. An image of the corium jet behavior in the coolant was taken by a high-speed camera every millisecond. Thermocouple junctions installed in the vertical direction of the coolant were cut sequentially by the falling corium jet. It was clearly observed that the visualization image of the corium jet taken during the fuel-coolant interaction corresponded with the temperature variations in the direction of the falling melt. The corium penetrated through the coolant, and the jet leading edge velocity was 2.0 m/s. Debris smaller than 1 mm was 15% of the total weight of the debris collected after a fuel-coolant interaction test, and the mass median diameter was 2.9 mm.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.5
• /
• pp.547-556
• /
• 2019

Thinned, small larch logs have small diameters and no value-added final use, except as wood chips, pallets, or fuel wood, which are products with very low economic value; however, their mechanical strength is suitable for structural applications. In this study, small larch logs were sawed, dried, and cut into square timbers (with a $90mm{\times}90mm$ cross section) that were laterally glued to form core panels used to manufacture cross-laminated timber (CLT) wall panels. The surface and back of these core panels were covered with 12-mm-thick structural plywood panels, used as cross bands to obtain three-ply CLT wall panels. This attachment procedure was conducted in two different ways: gluing and pressing (CGCLT) or gluing and nailing (NGCLT). The size of the as-manufactured CLT panels was $1,220mm{\times}2,440mm$, the same as that of the plywood panels. The final wall panels were tested under lateral shear force in accordance with KS F 2154. As the lateral load resistance test required $2,440mm{\times}2,440mm$ specimens, two CLT wall panels had to be attached in parallel. In addition, the final CLT panels had tongued and grooved edges to allow parallel joints between adjacent pieces. For comparison, conventional light-frame timber shear walls and midply wall systems were also tested under the same conditions. Shear walls with edge nail spacing of 150 mm and 100 mm, the midply wall system, and the fabricated CGCLT and NGCLT wall panels exhibited maximum lateral resistances of 6.1 kN/m (100%), 9.7 kN/m (158%), 16.9 kN/m (274%), 29.6 kN/m (482%), and 35.8 kN/m (582%), respectively.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.6
• /
• pp.266-283
• /
• 2022

With the rapid development of autonomous vehicle technology, unexpected accidents are occurring. Therefore, it is necessary to minimize user accident damage through the development of autonomous traffic safety education. Since edge cases, accident type, and risk factor analysis are important for realistic education, overseas case studies and demonstrations were carried out, and based on this, two curriculum for service providers and general users were developed. The service provider curriculum consisted of OEDR, sudden stop, cut-in, take-over, defensive driving, system malfunction, policy and information security education, and the general user curriculum consisted of attention duty, take-over, operating design domain, accidents type, laws, functions, information security education.

• Composites Research
• /
• v.21 no.3
• /
• pp.9-17
• /
• 2008

In this paper, the low velocity impact characteristics of filament winding CFRP pressure vessel was investigated using numerical and experimental methods. The cylinder part of CFRP vessel was impacted using triangular shape impactor which simulated the sharp edge of dropping tools and impact response behavior of CFRP was reviewed. The mechanical behavior, such as deformation and stress distribution, were also predicted by explicit finite element method and the validity of the model was investigated. For the quantitative evaluation of the residual strength of the pressure vessel after impact, a series of the ring specimens was cut from the impacted vessel and its burst pressure was measured by hydraulic pressure hoop tension test. As the results, the relationship between the residual strength degradation and the impact energy was successively obtained and a useful methodology to evaluate quantitatively the impact damage tolerance of CFRP pressure vessel was established.

• Korean Journal of Heritage: History & Science
• /
• v.51 no.4
• /
• pp.84-107
• /
• 2018

Cheommojik is a pile cloth, a type of textile whose surface is covered with short piles. The term chaedam was used during the late Joseon dynasty to refer to pile cloth rugs, while the terms yoongjeon, dantong and yangtanja were used in the early twentieth century. Various documents, newspaper articles and photographs confirm that pile cloth rugs were used by the general public as well as the royal family from the late Joseon dynasty onward, and that there were domestic manufacturers of such rugs at that time. This study investigated six pile cloth rugs that were produced after the late Joseon dynasty, five of which feature Persian knots made of cut pile, the other being made with the loop pile method. The cut pile rugs are rectangular in shape and measure between 72-98cm by 150-156cm; and they are decorated in the middle with patterns of butterfly, deer, and tiger or the ten longevity symbols, and along the edges with patterns composed of 卍 symbols. The ground warp of all six rugs are made from cotton yarn, while the ground weft is made of cotton yarn on three pieces, wool on one piece and cotton and viscose rayon. The ground weft yarn from four pieces are Z-twist yarn made with two or more S-twist cotton yarn. Four to six colors were used for the pile weft, all being natural colors except for red. Two or more S- or Z-twist yarn were twisted together in the opposite twist for the pile weft, with the thickness determining the number of threads used. Six or more weft threads were used to make the start and end points of the rug; and the ground warp ends were arranged by tying every four of them together. For the left and right edges, three or more threads were wrapped together into a round stick-like form, and the second and third inner ground warps from the edges were stitched on to the wrapped edge. For the loop pile, loops were made in the direction of the warp; the ground warp and the ground weft may have been made with cotton, the pile warp with wool yarn. An analysis of the components of three rugs was conducted to determine which types of animal hair were used for the pile weft. Despite some inconclusive results, it was revealed that goat hair and fat-tailed sheep hair were used, raising the possibility that various kinds of animal fur were used in the production of pile cloth rugs. The six rugs examined in this study are estimated to have been made between the late 1800s and the early 1900s. Although the manufacturer of the rugs cannot be confirmed, we concluded that the rugs were produced in Korea after referring to the documentation of the domestic production of pile cloth rugs during the aforementioned period and the form and placements of the patterns on the rugs.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.34 no.4
• /
• pp.109-116
• /
• 2024

β-Ga₂O₃ is a representative ultra-wide bandgap (UWBG) semiconductor that has attracted much attention for power device applications due to its wide-bandgap of 4.9 eV and high-breakdown voltage of 8 MV/cm. In addition, because solution growth is possible, it has advantages such as fast growth rate and lower production cost compared to SiC and GaN [1-2]. In this study, we have successfully grown Si-doped 10 mm thick Si-doped β-Ga₂O₃ single crystals by the EFG (Edge-defined Film-fed Growth) method. The growth direction and growth principal plane were set to [010] / (010), respectively, and the growth speed was 7~20 mm/h. The as-grown β-Ga₂O₃ single crystal was cut into various crystal planes (001, 100, ${\bar{2}}01$) and off-angles (1^o, 3^o, 4^o), and then surface processed. After processed, the homoepitaxial layer was grown on the epi-ready substrate using the HVPE (Halide vapor phase epitaxy) method. The processed samples and the epi-layer grown samples were analyzed by XRD, AFM, OM, and Etching to compare the surface properties according to the crystal plane and off-angle.

• Korean Journal of Environment and Ecology
• /
• v.17 no.2
• /
• pp.144-152
• /
• 2003

The purpose of this study was to investigate the effects of lime fertilization and light intensity on beech regeneration strategy in a mature beech forest(ca. 150 years old) gaps, which was located in the soiling areas Germany, where the soil is an acid brown earth. For the experiment canopy gaps of 30m diameter were cut, and one canopy gap remained as untreated while the other was limed(3t dolomite h $a^{-1}$). Soil chemistry, soil water potential, light intensity(PAR), ground vegetation, beech seedlings and mycorrhiza were investigated along transect from the stands into gaps to the north. The results of this study are followings: 1) In the limed gap, soil chemistry was greatly improved and a vigorous herb layer developed as compared to the unlimed gap. 2) Development and growth of the beech seedlings in the unlimed gap were generally deficient. Specially, developments of lateral roots were very lack. 3) Through the lime fertilization, the minerals contents of beech leaves such as calcium(Ca) and magnesium(Mg) were increased, while manganese(Mn) was decreased. There was antagonism between potassium(K) and calcium(Ca) or magnesium(Mg). 4) The relative mycorrhiza frequency(RM) in beech seedlings of the southern edge was very higher than that of the middle part, and through the lime fertilization extension of the species Laccaria amethystina appeared clearly. The results of this study showed that lime fertilize in forest, where the soil is acid, will be necessary..

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.3
• /
• pp.1645-1651
• /
• 2015

This paper describes the changes of shape accuracy in workpiece materials depending on the turning clearance angle. The experiments started from choosing three workpiece materials, SM45C(machine structural carbon steel), STS303(stainless steel) and SCM415 (chrome-molybdenum steel). The experiments showed specifically how features of selected materials changed when they were processed with diverse machining depths, 0.1 mm, 0.2 mm and 0.3 mm, with various negative angles, $0.0^{\circ}(-6.0^{\circ})$, $0.3^{\circ}(-6.3^{\circ})$ and $0.9^{\circ}(-6.9^{\circ})$, and called cutting edge inclination starting from a fixed rotational speed, 2,500 rpm, focusing on the feed rate, 0.07 mm/rev and 0.10 mm/rev. The results of the accuracy of processing, cylindricity, deviation from coaxiality, etc. were compared using the graph and table. The accuracy of cylindricity in the order of degree $0.0^{\circ}{\rightarrow}0.3^{\circ}{\rightarrow}0.9^{\circ}$ depending on the workpiece materials showed the best cylindricity when it was $0.9^{\circ}$. In conclusion, the accuracy improved in specific degrees irrespective of the quality of the materials when the bite negative angles increased. This means that workability improved in these experiments. In addition, the processing shape changed depending on depth of the cut and feed rate.

• The KIPS Transactions:PartA
• /
• v.16A no.6
• /
• pp.453-462
• /
• 2009

Studies on software plagiarism detection, prevention and judgement have become widespread due to the growing of interest and importance for the protection and authentication of software intellectual property. Many previous studies focused on comparing all pairs of submitted codes by using attribute counting, token pattern, program parse tree, and similarity measuring algorithm. It is important to provide a clear-cut model for distinguishing plagiarism and collaboration. This paper proposes a source code clustering algorithm using a probability model on extreme value distribution. First, we propose an asymmetric distance measure pdist($P_a$, $P_b$) to measure the similarity of $P_a$ and $P_b$ Then, we construct the Plagiarism Direction Graph (PDG) for a given program set using pdist($P_a$, $P_b$) as edge weights. And, we transform the PDG into a Gumbel Distance Graph (GDG) model, since we found that the pdist($P_a$, $P_b$) score distribution is similar to a well-known Gumbel distribution. Second, we newly define pseudo-plagiarism which is a sort of virtual plagiarism forced by a very strong functional requirement in the specification. We conducted experiments with 18 groups of programs (more than 700 source codes) collected from the ICPC (International Collegiate Programming Contest) and KOI (Korean Olympiad for Informatics) programming contests. The experiments showed that most plagiarized codes could be detected with high sensitivity and that our algorithm successfully separated real plagiarism from pseudo plagiarism.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.235-243
• /
• 2002

Ni-base superalloys are used extensively in industry, both in aeroengines and land based turbines. About 60% by weight of most modern gas turbine engine structural components are made of Ni-base superalloys. To satisfy practical demands, the efficiency of gas turbine engines has been steadily and systematically increased by design modifications to handle higher turbine inlet or firing temperatures. However, the increase in operating temperatures has lead to a decrease in the life of components and increase in costs of replacement. Moreover, around 80% of the large frame size industrial/utility gas turbines operating in the world today were installed in the mid-sixties to early seventies and are now 25 to 30 years old. Consequently, there are greater opportunities now to repair and refurbish the older models. Basically, there are two major factors influencing the weldability of the cast alloys: strain-age cracking and liquation cracking. Susceptibility to strain-age cracking is due to the total Ti plus AI content of the alloy; Liquation cracking is due either to the presence of low melting constituents or constitutional liquation of constituents. Though Rene 41 superalloy has 4.5wt.% total Ti and Al content and falls just below the safe limit proposed by Prager et al., controlled grain size and special heat treatments are needed to obtain crack-free welds. Varying heat treatments and filler materials were used in a laboratory study, then the actual welding of service parts was carried out to verity the possibility of crack-tree weld of components fabricated from Rene 41 superalloy. The microstructural observations indicated that there were two kinds of carbides in the FCC matrix. MC carbides were located along the grain boundaries, while M$_{23}$C$_{6}$ carbide was located both inter and intra granularly. Two kinds of filler materials, Rene 41 and Hastelloy X were used to gas tungsten arc weld a patch into the sheet metal, along with varying pre-weld heat treatments. The microstructure, hardness and tensile tests were determined. The service distressed parts were categorized into three classes: with large cracks, with medium cracks and with small or no visible cracks. No significant difference in microstructure among the specimens was observed. Specimens were cut from the corner and the straight edge of the patch repair, away from the corner. The only cracks present were found to be associated with inadequate surface preparation to remove oxidation. Guidelines for oxide removal and the welding procedures developed in the research enabled crack-free welds to be produced.d.