• Journal of Korean Society of Forest Science
• /
• v.96 no.3
• /
• pp.362-368
• /
• 2007

This study was conducted to estimate merchantable volume and yield per diameter (DBH) class of Pinus koraiensis and Larix kaempferi. Stem volume of trees in each diameter class was calculated using the existing equations for taper and height curve. Saw logs and pulpwood volume were then estimated from the stem volume in each diameter class. The final step was to estimate merchantable volume and yield from saw logs, assuming saw logs were used for lumber (boards or dimension products) production only. The results showed that the stem volume of Larix kaempferi was 23~38% higher than that of Pinus koraiensis at the same diameter classes. Both species were able to produce saw logs from the diameter class of 18 cm. Saw logs and pulpwood yield for both species rapidly increased due to the size limitation on small end diameter. This yield reached a maximum of 90% and 88% at 26 cm and 38cm diameter class, respectively, for Pinus koraiensis and Larix kaempferi. Lumber yield estimated for board products ranged from 23% to 56%. In the case of dimension products, Lumber yield became significantly smaller as saw logs were used for larger dimension products. These results can be used for calculating merchantable volume and economic value of trees, as well as determining final lumber products.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2004.12a
• /
• pp.27-34
• /
• 2004

This experiment was carried out to examine the effects of morphology on properties of La-Co substituted SrM ferrite. The magnetic properties of calcined and sintered materials varied with the substitutional amount of La and Co elements in Sr-ferrite. In the substituted SrM ferrite, the atomic fraction x of La is directly related to the mole ratio n of iron oxide and the atomic fraction y of Co by equation x=2ny. The HcJ values of the calcined powder were about 270 kA/m and 240 kA/m with x=0.3 and K=0.2, respectively at stoichiometriy, n=6.0. Crystallites of the sintered material were grown with a plate shape, and their size decreased with increasing mole ratios. Such a shape was caused by the initial state of crystallite formed after calcination. In case of x=0.3 and n=6.0, Br was 415 mT and HcJ was 355 kA/m, and in x=0.2 and n=6.0, Br was 410 mT and HcJ was 370kA/m. The squareness in 2nd quarter of BH curve with x=0.2 was smoothly improved compared with x=0.3

• Parasites, Hosts and Diseases
• /
• v.23 no.2
• /
• pp.221-229
• /
• 1985

The echinostomatid metacercariae encysted in the gill of the fresh water fish, Pseudorasbora larva were identified through obtaining adult worms after eBperimental infection to mice. In addition, a brief course of worm development and maturation was observed in this experimental host. The results were as follows: 1. The echinostomatid metacercariae were elliptical, golden yellow, 0.073∼0.078 mm long and 0.0541∼0.065 mm wide. Their head portions were characterized by the presence of a head crown armed with collar spines of total 24 in number and interrupted at the mid-dorsal side of the oral sucker. 2. The average rate of worm recovery froth 12 mice (on the 1-2lth postinfection days) was 19.4 % and the rate revealed no decrease in accordance with the increase of infection duration. The worms were collected chiefly from the lower part of the small intestine. 3. After the infection, their sexual maturation was attained in 5 days and their growth in size nearly completed in 7 days. The early growth curve of genital organs was S shape while that of nongenital organs was C form. In 5 day old worms, 1 or 2 eggs were found from their uteri and the stools of mice revealed echinostomatid eggs from the 5-6th postinfection day. 4. The 7 day old adult worms were ovoid in shape, 0.54-0.69 mm long and 0.29-0.34 mm wide, and characterized by a well developed head crown with 24 collar spines and vitelline follicles distributed from the acetabular level down to the posterior end of body. Based on these characters they were identified to be Echinochasmus japonicus Tanabe, 1926. From these results, it is verified that p. larva is one of the second intermediate hosts of 5. jatonicus in Korea.

• Journal of the Korean Magnetics Society
• /
• v.10 no.5
• /
• pp.210-219
• /
• 2000

The magnetoresistance characteristics of FeN/Co/Cu/Co and FeN/Co/Cu/Co/Cu/Co/FeN multilayers using ferromagnetic iron-nitrides (FeN) has been studied. The microstructure of FeN film is the mixed ${\alpha}$-Fe and $\varepsilon$-Fe$_3$N phase on the condition that the flow rate of N$_2$ gas is over 0.4 sccm. The magnetoresistance effect is observed because of shape magnetic anisotropy induced by needle-shaped $\varepsilon$-Fe$_3$N phase. This magnetoresistance effect changes, because the degree that the shape magnetic anisotropy adheres to the adjacent Co pinned layer is varied according to the flow rate of N$_2$ gas and the thickness of FeN film. The best magnetoresistance effect is obtained on the condition that the thickness of Co free layer is 70 ${\AA}$ and the maximum MR ratio(%) value of 3.2% shows in the FeN(250 ${\AA}$)/Co(70 ${\AA}$)/Cu(25 ${\AA}$)/Co(70 ${\AA}$)/Cu(25 ${\AA}$)/Co(70 ${\AA}$)/FeN(250 ${\AA}$) mutilayer film which is fabricated at the N, gas flow rate of 0.5 sccm and the FeN film thickness of 250 ${\AA}$. Four steps are observed in the magnetoresistance curve owing to this difference of coercive force, because respective magnetic layers in the multilayer possess different coercive forces. These effects observed in these mutilayer films can be expected to application to the memory device the same MRAM as can carry out simultaneously four signals.

• The Korean Journal of Pharmacology
• /
• v.20 no.2
• /
• pp.23-34
• /
• 1984

To investigate diurnal variations of opiate receptor binding and its modification by experimental condition or treatment of various centrally-acting drugs, the amount of maximum $^3H-morphine$ binding in rat midbrain homogenates was measured at 4 hour intervals for 24 hours. Animals were conditioned under the controlled L : D, 12 : 12 cycle or D: D, 12 : 12 cycle, for 3 weeks and treated with 0.5 ml of physiological saline or drugs for 2 weeks. A highly significant diurnal rhythm with peak at 22 hour of early dark phase with an amplitude$(0.68{\pm}0.06\;pmole/mg\;protein)$ of +51.1% and nadir $(0.33{\pm}0.03\;mole/mg\;prtein)$ at 18 hour of late light phase with an amplitude of -26.6% was found in control group. 24 tour mean of $^3H-morphine$ binding was $0.45{\pm}0.03\;pmole/mg$ protein respectively. Constant dark adaptation or treatment of reserpine, pargyline, imipramine, amphetamine and chlorpromazine modified the diurnal rhythm in the time of peak and nadir binding shape, phase, amplitude of the diurnal curve and 24 hour mean of $^3H-morphine$ binding. However, Kd values were not changed in all experimental groups : Statistical analysis at times of least and great binding indicates that the differences in $^3H-morphine$ binding were due to changes not in the affinity, but in the number of binding sites. The results are interpreted with regard to the diurnal rhythm of opiate receptor finding. The modes of action of psychoactive drugs are closely related to postulated changes of receptor sensitivity in neuropharmacological aspects.

• Journal of the Korean Society of Radiology
• /
• v.17 no.2
• /
• pp.175-184
• /
• 2023

Based on the actual shape of the detector and the data provided by the manufacturer, the shape of the detector was implemented through Penelope simulation and applied to the appropriate four-layer thickness based on the efficiency obtained from the measurements. Efficiency calculations to determine the effect of the simulated number of Full Energy Peak Efficiency(FEPE) channels in the detector and the outside contact layer in the crystal on the Full Energy Peak Efficiency were performed for various four-layer thicknesses of 0.3, 0.5, 0.7, 1.0, 1.2, and 1.4 mm using the Penelope Code. When the thickness of the external contact layer was increased by 5 times, the Full Energy Peak Efficiency decreased by about 36% for 59.50 keV, and the Full Energy Peak Efficiency decreased by 10% for 1836. In addition, as it increased by 10 times, the Full Energy Peak Efficiency decreased by about 20% for 59.54 keV, and 7% for 1836.01 keV. The Penelope simulated Full Energy Peak Efficiency channel decreases exponentially with the increase in the four layers. In addition, it was confirmed that the total effect curve was well matched with a relative difference of less than 3.5% in the 0.3-1.4 mm dead layer thickness region. However, it was found that the inhomogeneous dead layer is still a parameter in the Monte Carlo model.

• Journal of Korea Multimedia Society
• /
• v.16 no.2
• /
• pp.206-212
• /
• 2013

Information and Communications Technologies(ICT) represented by Multimedia, Virtual Reality and Network could be used as the better ways to preserve and restore the original shape of cultural contents. This paper presents the detailed methods of Multimedia and Virtual Reality technologies to digitally implement the traditional wooden buildings which are called as a typical 'Korean Cultural Content." We implemented a 3D modeling of architectural parts, realized a roof curve, and texture-mapped the material qualities of traditional wooden buildings by using Graphic techniques. In addition, the information, which is implemented by marker-based Augment Reality, for the traditional wooden buildings can be obtained through the mobile appliances such as a smart phone. We, also, presented how to practically use the implemented digital Korea traditional wooden buildings.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.4
• /
• pp.1807-1812
• /
• 2014

A plastic has a various advantages in engineering elements that it can be formed a curve surface without restriction of shape and product the high volume with various color and lower price. Also, it is being used for many parts of automobile as the weight of cars is getting lighter. The Door A-Fuel Filler is a automobile plastic part by injection molding production. The injected products are involved a lot of factors for the inferior goods after painting. Therefore the painted products are required to have the process of the polishing in order to eliminate the faults. Now polishing process is being worked by hands. The workers tend to evade the process of polishing because the working needs a lot of powers momentarily. This paper presents the development of auto-polishing system that can check the inferior goods by the vision system and control the polishing process by the motion system. As a result, Shorten production time (30 seconds), and decreases by 1 person to work to increase the competitiveness of the production cost was to expect improvement.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.7
• /
• pp.623-626
• /
• 2014

The LBB (Leak Before Break) concept is based on evaluating the fracture toughness. NUREG 1061, Vol.3 announced that the specimen for evaluating fracture resistance needs to have same thickness or thicker than pipe. Therefore, it is difficult to collect specimen from pipe which has same thickness as a pipe. So, ASTM standard suggested the use of standard specimen with 1 inch thickness. However, it has been known that an application of LBB by test results of standard specimen is conservative compare with that by real pipe. In this study, to supplement such conservatism, the evaluation of fracture resistance characteristics was performed with curved CT specimen, which has same thickness and curvature as a pipe. In addition, fracture resistance characteristics of curved CT specimen were compared with those of CT specimen. For this, shape factor F, hpl and g were obtained from FEM analysis using the limit load method.

• Korean Journal of Remote Sensing
• /
• v.28 no.5
• /
• pp.549-559
• /
• 2012

This paper presents a comparative analysis on the applicability of a priori statistic information about adjustment models when the surface shape parameters are estimated at an arbitrary point in an elevation data. Although the reliability of the estimates are known to be affected by surface condition and the adjustment models, there has been little research in a systematic and detail way. When the raw data have been taken from a real measurement, its true value cannot be known, however, thus this study used simulation data in order to analyze clearly the applicability of adjustment models. The generation of simulated data was performed by superimposing horizontal, slope, and curve surfaces and adding a certain amount of noise. Comparative analysis was performed by associating the a posteriori estimates with a priori statistics of each adjustment models. The experimental results show the estimation characteristics of adjustment models against varying surface conditions.