• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.2
• /
• pp.270-277
• /
• 2013

Single phase induction motor(SPIM) is used widely because it is driven by single phase source. However, the efficiency of the motor is not good due to saturation of magnetic material. To analyze the motor accurately, the magnetic saturation characteristics should be considered in analysis of equivalent circuit. In this paper, lumped parameter of circuit are derived from multi phase induction motor using method of symmetrical coordinates. Also, we presents a method for the equivalent circuit analysis of SPIM using magnetic saturation rate. The magnetic nonlinearity is considered deriving magnetizing reactance from voltage-current saturation curve. As a results, current characteristic, torque, output and efficiency are shown through analysis of equivalent circuit. A simulation results of SPIM will be used to improve the characteristics and efficiency of motor.

• Journal of Welding and Joining
• /
• v.16 no.3
• /
• pp.74-84
• /
• 1998

The microstructures of the HAZ (Heat Affected Zone) are generally different from the base metal due to rapid thermal cycle during welding process. Particuraly, CGHAZ (Coarsened Grain Heat Affected Zone) near the fusion line is the most concerned region in which many metallurgical and mechanical discontinuities have been normally generated. A computer program by the numerical formularization of phase transformation during cooling with different rates was developed to generate the CCT diagram, and to predict microstructural (phase) changes in the CGHAZ. In order to verify simulated results, isothermal and continuous cooling transformation experiments were conducted. The simulated and experimental results showed that the developed computer model could successfully predict the room temperature microstructural changes (changes in volume fraction of phases) under various welding conditions (heat input & cooling rate $(Δt_{8/5})$).

• International Journal of Air-Conditioning and Refrigeration
• /
• v.9 no.4
• /
• pp.27-36
• /
• 2001

A new two-phase non-boiling convective heat transfer correlation for turbulent flow $(Re_{SL}>4000)$ in vertical tubes with different fluid flow patterns and fluid combinations was developed using experimental data available from the literature. The correlation presented herein originates from a careful analysis of the major non-dimensional parameters affecting two-phase heat transfer. This model takes into account the appropriate contributions of both the liquid and gas phases using the respective cross-sectional areas occupied by the two phases. A total of 255 data points from three available studies (which included the four sets of data) were used to determine the curve-fitted constants in the improved correlation. The performance of the new correlation was compared with two-phase correlations from the literature, which were developed for specific fluid combinations.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.6
• /
• pp.397-403
• /
• 2021

In this paper, phase shedding algorithm that measuring to converter's input and output parameter during real-time to control the number of driving converters is proposed. The proposed phase-shedding algorithm drives the DVR power supply with the optimal converter's combination without the loss calculation curve and the lookup table in which the efficiency is measured in advance. The proposed algorithm was implemented through a digital controller and verified in a two-modular LLC converter with a single rated power of 60 Win a 120 W DVR power supply system. Experimental results are presented to prove the validity of the proposed algorithm.

• Journal of the Korean Ceramic Society
• /
• v.32 no.8
• /
• pp.915-921
• /
• 1995

The morphotropic phase boundary and phase transitions of the solid solutiion system, (1-x)(Na1/2Bi1/2)TiO3-PbTiO3＋xPbTiO3 were studied by investigating changes in crystal structure, variations in permittivity with temperature, and calorimetric behavior. It was observed that the morphotropic phase boundary (MPB) of this solid solutiion system was at near 14 mol% of PbTiO3. Compositions containing less than 10mol% PbTiO3 (x<0.1) exhibited a phase transition, i.e. ferroelectric rhombohedrallongrightarrowparaelectric paraelectric cubic, with increasing temperature. Composition containing more than 14 mol% PbTiO3 (x 0.14) showed a phase transition from ferroelectric tetragonal to paraelectric cubic. In the composition range of 0.1$\varepsilon$ (T) curve, which coincided with a phase transition from ferroelectric rhombohedral to an intermediate phase, was also found.

• International Journal of Highway Engineering
• /
• v.7 no.1 s.23
• /
• pp.49-61
• /
• 2005

The dynamic modulus of hot mix asphalt can be determined according to the different combinations of testing temperature and loading frequency. The superposition rule is adapted to get the master curve of dynamic modulus for each hot mix asphalt. There are couple of different methods to get the shift factor which is a key for making the master curve. In this paper, Arrehnius, 2002 AASHTO, and experimental method was employed to get the master curve. Evaluation of dynamic modulus for 25mm base course of hot mix asphalt with granite aggregate and two asphalt binders(AP-3 and AP-5) was carried out. Superpave Level 1 Mix Design with gyratory compactor was adopted to determine the optimum asphalt binder content(OAC) and the measured ranges of OAC were between 4.1% and 4.4%. UTM was used for laboratory test. The dynamic modulus and phase angle were determined by testing on UTM, with 5 different testing temperature(-10, 5, 20, 40, & $55^{\circ}C$) and 5 different loading frequencies(0.05, 0.1, 1, 10, 25 Hz). Using the measured dynamic modulus and phase angle, the input parameters of Sigmoidal function equation to represent the master curve were determined and these will be adopted in FEM analysis for asphalt pavements. The shift factor and activation energy for determination of master curve were calculated.

• Journal of the korean Society of Automotive Engineers
• /
• v.6 no.4
• /
• pp.46-53
• /
• 1984

The analysis of temperature distribution and change of metallic structures during water quench were presented by finite element method. In temperature calculation the equation of unsteady state hear conduction problem considering latent heat due to phase transformation was applied to finite solid cylinder, SM 45C of 40mm diameter and 40mm height. In metallic structure analysis iso-thermal transformation curve and the equations of evolution in pearlite-martensite transformation were applied. The calculated results upon temperature and metallic structures were agreed with those of experimental observations.

• Bulletin of the Korean Chemical Society
• /
• v.22 no.5
• /
• pp.503-506
• /
• 2001

Separation of lithium isotopes was investigated by chemical ion exchange with a hydrous manganese(IV) oxide ion exchanger using an elution chromatography. The capacity of manganese(IV) oxide ion exchanger was 0.5 meq/g. One molar CH3COO Na solution was used as an eluent. The heavier isotope of lithium was enriched in the solution phase, while the lighter isotope was enriched in the ion exchanger phase. The separation factor was calculated according to the method of Glueckauf from the elution curve and isotopic assays. The single stage separation factor of lithium isotope pair fractionation was 1.021.

• Journal of Advanced Marine Engineering and Technology
• /
• v.19 no.2
• /
• pp.20-26
• /
• 1995

The very rapid cooling problem from $820^{\circ}$C to $20^{\circ}$C on the surface of the steel by thermal conduction including the latent heat of phase transformation of steel and by transient boiling heat transfer of water are considered to principal problem in quenching. The transient boiling process of water at the surface of specimen during the quenching process were experimentally analyzed. Then the heat flux was numerically calculated by the numerical method of inverse heat condition problem. In this report, the simulation program to calculate the cooling curves for large rolls was made using the subcooled transient boiling curve as a boundary condition. By this simulation program, the cooling curves of rolls from D=50mm to D=200mm were calculated and the effects of agitation of circulation of water also investigated.

• The Journal of Natural Sciences
• /
• v.8 no.1
• /
• pp.17-22
• /
• 1995

Dielectric constant was measured near the consolute point of a binary mixture of water and Poly[bis(methoxyethoxyethoxy)phosphazene], MEEP. Dielectric constant changed incontinously at phase separation temperature plotted against the concentration to abtain coexistence curve. The critical temperatures and the critical concentration were $71^{\circ}C$, 5.5% as determined from the coexistence curve, respectivley. The critical exponent of dielectric constant, $\theta$, was 0.85. The dependence of dielectric constant on frequency is discussed in this report.