• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 추계학술대회 논문집
• /
• pp.28-30
• /
• 2007

For the design of the voltage regulation module(VRM) having a high performance, current sensing is one of the most important functions. In this paper, three different methods for sensing the current in the multi-phase synchronous buck converter are analyzed considering the efficiency, accuracy and cost. The experiments are performed for the three current sensing methods to verify the theoretic analysis.

• Journal of Power Electronics
• /
• 제16권5호
• /
• pp.1791-1801
• /
• 2016

This paper considers a carrier based signal injection method for use in the three shunt sensing inverter (TSSI) for sensorless motor control. It also analyzes the loss according to the injection axis of the voltage signal. To remove both the phase current and rotor position sensors, a sensorless method and a phase current reconstruction method can be simultaneously considered. However, an interaction between the two methods can be incurred when both methods inject voltage signals simultaneously. In this paper, a signal injection based sensorless method with the 120° OFF Discontinuous PWM (DPWM) is implemented in a TSSI to avoid this interaction problem. Since one leg does not have a switching event for one sampling period in the 120° OFF DPWM, the switching loss is altered according to the injection axis. The switching loss in the d-axis injection case can be up to 32% larger than that in the q-axis injection case. Other losses according to the injection axis are also analyzed.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 추계학술대회 논문집 학회본부 C
• /
• pp.773-775
• /
• 1998

This paper describes the highly sensitive Si Hall magnetic sensing system which can measure the earth magnetic field. Generally, the important parameters in Hall device which degrade the ability of magnetic detection are offset voltage and 1/f noise. The offset voltage and 1/f noise in Hall plates can be reduced by spinning current method. In this paper, we implement the highly sensitive Si Hall magnetic sensing system using spinning current method. As a result, the minimum detectable magnetic field is 0.1G.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제6권1호
• /
• pp.361-378
• /
• 2012

Most of the current frequency hopping (FH) based dynamic spectrum access (DSA) methods concern a reactive channel access scheme with synchronous inter-channel spectrum sensing, i.e., FH is reactively triggered by the primary user (PU)'s return reported by spectrum sensing, and the PU channel to be switched to is assumed precisely just sensed or ready to be sensed, as if the inter-channel spectrum sensing moments are synchronous. However, the inter-channel spectrum sensing moments are more likely to be asynchronous, which risks PU suffering more interference. Moreover, the spectrum sensing is usually erroneous, which renders the problem more complex. To address this problem, we propose a proactive FH based DSA method against both erroneous spectrum sensing and asynchronous inter-channel spectrum sensing (moments). We term it as proactive DSA. The optimal FH sequence is obtained by dynamic programming. The complexity is also analyzed. Finally, the simulation results confirm the effectiveness of the proposed method.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 전력전자학술대회 논문집
• /
• pp.195-196
• /
• 2012

In recent years, in an effort to improve the efficiency and the power density of the front-end power factor correction(PFC), the interleaving of multiple converter is employed. The conventional interleaved continuous conduction mode(CCM) boost PFC converter requires input and output voltage sensing and three current sensing to obtain current balancing between modules. In this paper, the interleaved CCM PFC converter based on modulated carrier control is proposed. With the proposed method, two phase interleaved PFC can be realized simply without line voltage sensing resistor and can achieve current balancing without additional current sensing resistor on common return path. The simulation studies are carried out to verify the effectiveness of the proposed control scheme.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.359-359
• /
• 2011

This study reports the H2S gas sensing properties of CuO / ZnO nano-hetero structure bundle and the investigation of gas sensing mechanism. The 1-Dimensional ZnO nano-structure was synthesized by hydrothermal method and CuO / ZnO nano-heterostructures were prepared by photo chemical reaction. Scanning electron microscopy (SEM) and X-ray diffraction (XRD) spectra confirmed a well-crystalline ZnO of hexagonal structure. In order to improve the H2S gas sensing properties, simple type of gas sensor was fabricated with ZnO nano-heterostructures, which were prepared by photo-chemical deposition of CuO on the ZnO nanorods bundle. The furnace type gas sensing system was used to characterize sensing properties with diluted H2S gas (50 ppm) balanced air at various operating temperature up to 500$^{\circ}C$. The H2S gas response of ZnO nanorods bundle sensor increased with increasing temperature, which is thought to be due to chemical reaction of nanorods with gas molecules. Through analysis of X-ray photoelectron spectroscopy (XPS), the sensing mechanism of ZnO nanorods bundle sensor was explained by well-known surface reaction between ZnO surface atoms and hydrogen sulfide. However at high sensing temperature, chemical conversion of ZnO nanorods becomes a dominant sensing mechanism in current system. Photo-chemically fabricated CuO/ZnO heteronanostructures show higher gas response and higher current level than ZnO nanorods bundle. The gas sensing mechanism of the heteronanostructure can be explained by the chemical conversion of sensing material through the reaction with H2S gas.

• Journal of Electrical Engineering and Technology
• /
• 제11권1호
• /
• pp.241-246
• /
• 2016

This paper presents a method that can improve the performance of permanent magnet synchronous motor current control by minimizing the measured current phase delay caused by the Low Pass Filter(LPF) used to cut off the noises that flowed in when feedback currents are measured. Although existing methods that change the Cutoff Frequency of the LPF can minimize phase delays during high speed rotations, their noise cutoff effects are much lower and this may lead to the decline of control performance. Therefore, in this study, an algorithm that can compensate current phase delays through relatively simple calculations from the synchronous motor d-q axis coordinate transformation matrix and the inverse transformation matrix is proposed and the validity of the proposed method is verified by comparing the waveform of the calculated current with the waveform of actual currents through simulations and experiments.

• 전력전자학회논문지
• /
• 제26권3호
• /
• pp.214-221
• /
• 2021

SiC MOSFETs require a faster and more reliable short-circuit protection circuit than conventional methods due to narrow short-circuit withstand times. Therefore, this research proposes a short-circuit protection circuit using a current-sensing circuit based on Rogowski coil. The method of designing the current-sensing circuit, which is a component of the proposed circuit, is presented first. The integrator and input/output filter that compose the current-sensing circuit are designed to have a wide bandwidth for accurately measuring short-circuit currents with high di/dt. The precision of the designed sensing circuit is verified on a double pulse test (DPT). In addition, the sensing accuracy according to the bandwidth of the filters and the number of turns of the Rogowski coil is analyzed. Next, the entire short-circuit protection circuit with the current-sensing circuit is designed in consideration of the fast short-circuit shutdown time. To verify the performance of this circuit, a short-circuit test is conducted for two cases of short-circuit conditions that can occur in the half-bridge structure. Finally, the short-circuit shutdown time is measured to confirm the suitability of the proposed protection circuit for the SiC MOSFET short-circuit protection.

• 한국전기전자재료학회논문지
• /
• 제22권1호
• /
• pp.12-16
• /
• 2009

Current sensing in power semiconductors involves sensing of over-current in order to protect the device from harsh conditions. This technique is one of the most important functions in stabilizing power semiconductor device modules. The sense FET is very efficient method with low power consumption, fast sensing speed and accuracy. In this paper, we have analyzed the characteristics of proposed sense FET and optimized its electrical characteristics to apply conventional 450 V power MOSFET by numerical and simulation analysis. The proposed sense FET has the n-drift doping concentration $1.5{\times}10^{14}cm^{-3}$, size of $600{\um}m^2$ with $4.5\;{\Omega}$, and off-state leakage current below $50{\mu}A$. We offer the layout of the proposed sense FET to process actually. The offerd design and optimization methods are meaningful, which the methods can be applied to the power devices having various breakdown voltages for protection.

• Journal of Power Electronics
• /
• 제16권5호
• /
• pp.1650-1660
• /
• 2016

This paper proposes a compensator to eliminate the DC bias of inductor current. This method utilizes an average-current sensing technique to detect the DC bias of inductor current. A small signal model of the DC bias compensation loop is derived. It is shown that the DC bias has a one-pole relationship with the duty cycle of the left side leading lag. By considering the pole produced by the dual active bridge (DAB) converter and the pole produced by the average-current sensing module, a one-pole-one-zero digital compensation method is given. By using this method, the DC bias is eliminated, and the stability of the compensation loop is ensured. The performance of the proposed compensator is verified with a 1.2-kW DAB converter prototype.