• Journal of the Korean Society of Tobacco Science
• /
• v.29 no.2
• /
• pp.66-73
• /
• 2007

This study was carried out to investigate the changes of curing condition on microclimate of temperature, relative humidity during curing process of burley tobacco leaves. The developed facility, ridge opening type was designed to open the central top roof. The air-cured variety, (N. tabacum cv KB111) was normally grown at the Eumseong tobacco experimental station in 2007. Mean daily temperature of $3^{\circ}C$ in ridge opening type curing facility was lower than that of conventional, whereas mean daily relative humidity of 12.6 % RH was lower in conventional curing facility for the entire stage of curing. The frequency distribution of optimal air temperature at daytime was higher 37.5 % in ridge opening type curing facility than that of conventional, while that of optimal relative humidity was lower 8.2 %. In the ridge opening type curing facility, the excessive drying leaves were low, however the price per kilogram was high. These results suggest that the new developed curing facility may be applied to improved microclimate inside the curing facility for curing burley.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2003.05a
• /
• pp.19-22
• /
• 2003

The purpose of this study is to analyze the curing effect of planar surface heater for concreting in cold weather. Some experiments were conducted to evaluate the temperature history of concrete structures cured with heating sheets. Results are as follows ; (1) The temperature of concrete showed continuously rising trend with the heating by planar surface heater under the cold environmental condition of 3~-12$^{\circ}C$. And after about 24 hours the maximum temperature of concrete was reached at 25~3$0^{\circ}C$. (2) The temperature of slab concrete heated by planar surface heater of 130W/$m^2$ was at least $25^{\circ}C$ higher than that of an exterior air, and the curing performance was much more effective than heating by hot wind machine. (3) Through the curing by planar surface heater for 48 hours, the concrete maturity of about 1.5 times to heating by hot wind machine was acquired.

• International Journal of Highway Engineering
• /
• v.16 no.3
• /
• pp.51-57
• /
• 2014

PURPOSES : This study is to suggest tunnel length to spray curing compound, based on the field tests. METHODS : At first field test, length from the entrance of tunnel to wet wall was checked by visual survey. The second and third test, various sensors were installed in concrete or in tunnel, such as RH sensor, temperature sensor, portable weather station and etc.. And also, test for bleeding and retaining water of concrete were conducted to evaluate environmental effect on concrete pavement. RESULTS : The result of the field experiment for tunnel length to spray curing compound indicates that length changes depending on tunnel length, season, and location. Environmental condition of a short tunnel was not much different between location near entrance and at center of tunnel. However, in case of a medium and long tunnel, effect of outside environmental condition decreased, when location moved into tunnel center of it. CONCLUSIONS : From the testing results, it can be proposed that optimum tunnel length to spray curing compound is 60m for a medium and long tunnel, and whole length for a short tunnel.

• Fibers and Polymers
• /
• v.7 no.2
• /
• pp.95-104
• /
• 2006

In order to improve the water swelling, thermal/mechanical and adhesion properties of waterborne polyurethane (WBPU), a series of the crosslinkable WBPUs containing hydrophilic ionic component, dimethylol propionic acid (20 mole%), were prepared by in-situ polymerization using a cross-linker hexakis (methoxymethyl) melamine (HMMM). Effects of the HMMM content (2, 4, and 6 wt%) and curing temperature on these properties of the crosslinked WBPUs samples were investigated. All properties were found to increase with increasing HMMM content. It was found that the optimum curing temperature of the WBPU films and adhesives was near $120^{\circ}C$, which was not dependent on the HMMM content.

• Journal of the Korean Ceramic Society
• /
• v.37 no.7
• /
• pp.726-729
• /
• 2000

The entitled report revealed that ZnO phosphor samples treated at different temperatures under a given reduction atmosphere show the radiation brightness increase with increase of temperature up to about 900$^{\circ}C$ but become decreasing beyond the temperature. The brightness deterioration with curing temperature at higher temperatures was explained by the decrease of excess zinc ions resulted from their evaporation. The comments will open possibility for different discussions on the experimental result by introducing numerical relationships between the concentration of the native defects and the curing condition.

• KSBB Journal
• /
• v.26 no.3
• /
• pp.193-198
• /
• 2011

Polyester was prepared through the esterification reaction between watsepaper liquefied by ethylene glycol and carboxylic acid. Liquefaction was carried out at the previously determined condition of 100 minutes, $160^{\circ}C$, and 3% sulfuric acid, and the hydroxyl value of the liquefied product was 411 mg KOH/g. In order to remove bubbles produced during the curing step, the method to introduce a slight nitrogen stream into reaction vessel and/or the method to preheat a polyester film at $85^{\circ}C$ before curing step were used alone or in combination. But if curing temperature was $130^{\circ}C$, simple method to cure a film for 5 hours at $130^{\circ}C$ without using both methods was found to be most effective. The polyesters prepared with various carboxylic acids showed significant different physical properties, and maleic acid was best among them. Also, the effect of reaction time and temperature, C/H (carboxyl group/hydroxyl group) ratio, and type of additive on the crosslinkage of polyester was investigated. Lithium hydroxide or citric acid as additive was used to enhance the crosslinkage of polyester and citric acid was proved to be much more effective than lithium hydroxide. The effect of reaction temperature on the crosslinkage was marginal, but the crosslinkage decreased above $130^{\circ}C$. The crosslinkage was 86% when the polyester was prepared at an optimum condition such as $130^{\circ}C$ and 15 minutes of reaction condition, 1.5 of C/H ratio, $130^{\circ}C$ and 5 hours of curing condition, and 10% addition of citric acid.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.17-20
• /
• 2005

This paper reported the temperature history of concrete placed at deck plate slab under cold climate condition by varying with surface insulating type. No curing sheet and simple insulation curing including non-woven fabric, double layer bubble sheet, the combination of double layer bubble sheet and non-woven fabric dropped temperature below zero within 24 hours, which caused frost damage at early age. On the other hand, the combination of double layer bubble sheet and non-woven fabric and double layer bubble sheet and styrofoam maintained minimum temperature above $4^{\circ}C\;and\;8^{\circ}C$, respectively. Based on core test results compressive strength of concrete with the combination of double layer bubble sheet and non-woven fabric and double layer bubble sheet and styrofoam was higher than those with other curing method due to good insulation effect.

• Journal of the Korean Society of Tobacco Science
• /
• v.7 no.2
• /
• pp.129-139
• /
• 1985

cent was carried out to study on the effect of temperature and humidity to chemical tobacco leaves during the yellowing stage. The results were follows : In the condition of high humidity and low temperature, yellowing time was delayed ; leaf color appeared lack clearness. In the higher temperature and the lower humidity during the yellowing stage : total sugar, reducing sugar and malic acid content were increased. Decomposition of nitrogenous components elevated in $38^{\circ}C$, 85%RH. Changes of total nitrogen content correlated with total curing time. Adecrease of linolenic acid with a corresponding increase of chlorogenic acid proceeded in the condition of low temperature and high humidity. In a view of tobacco quality by chemical components, the low temperature and high humidity during the yellowing stage decreased quality of tobacco leaves. It is considered to control of the proper condition of temperature and humidity during the yellowing.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.132-135
• /
• 2004

High-performance concrete (HPC) may be expected to differ from usual concrete with respect to shrinkage behavior, and it shows high autogenous shrinkage due to the use of very low water-binder ratio (w/b) and various admixtures. Therefore, in order to minimize the shrinkage stress and to ensure the service life of concrete structure, volumetric change of HPC should be understood. In this study, small prisms made of HPC with w/b of 0.32 and blast-furnace slag content of $0\%,\;30\%,\;and\;50\%$ were prepared to measure the volumetric changes such as autogenous shrinkage, drying shrinkage, and swelling under three different curing conditions. It was observed that the concrete cured. sealed condition showed only autogenous shrinkage while the concrete let to dry condition at temperature of $20^{\circ}C$ and relative humidity of $60\%$ during the test period showed both autogenous and drying shrinkage. Moreover, the concrete exposed to dry condition after 2-day water curing swelled and then started to shrink with age. The total shrinkage (autogenous+drying) of this concrete was smaller than that of the concrete cured dry condition, especially at early-age. Therefore, the early-age moisture curing is very effective to control or minimize the volumetric change and its induced stress of HPC.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1988.05a
• /
• pp.67-69
• /
• 1988

In this study, after changing the curing condition of hardner(DDM) and filler($SiO_2$) contents dielectric and dynamic mechanical properties were studied according to the variation of temperature. As the result we obtained a correlative $\alpha$-peak at 125-150[$^{\circ}C$] from dielectric and mechanical properties. With increasing curing condition and filler contents both dielectric and internal friction loss were, decreased, peak temperature shifted to high temperature, but there was no variation on peak temperature with filler contents. As the above result we knew the correspondence between dielectric and mechanical characteristics.