• 패션비즈니스
• /
• 제11권6호
• /
• pp.52-61
• /
• 2007

To increase the ultraviolet radiation (UVR) protection of cotton fabric, ultraviolet protection (UVP) materials were treated onto cotton fabric using a new technique, UV-curing. A photocrosslinkablepolymer, poly(ethylene glycol) dimethacrylate was used as a UV-curable resin in the presence of a small amount of photoinitiator. Two kinds of UVP materials were used, UV-absorber, 2,2'-dihydroxy-4-methoxy benzophenone, and UV-scatterer, $TiO_2/ZnO$ Pad-dry-cure method in employing these materials onto cotton was also conducted to compare the effectiveness and the washfastness of UVP treatment between curing methods. UVP treated cotton fabric showed a moderate increase in UVP in case of 2,2'-dihydroxy-4-methoxy benzophenone treatment and a high increase in case of $TiO_2/ZnO$. UV-curing method increased the washfastness of UVP property of $TiO_2/ZnO$ treated cotton fabrics. However, in case of 2,2'-dihydroxy-4-methoxy benzophenone, similar wash fastnesses of UV-cured and pad-dry-cured cotton were observed. It can be presumed that 2,2'-dihydroxy-4-methoxy benzophenone was not significantly affected by water since its hydrophobicity. In short, UV-curing of UVP materials onto cotton was successfully done, and treated cotton fabrics showed the increased UVP properties and an increased washfastness in some extent.

• International Journal of Concrete Structures and Materials
• /
• 제11권2호
• /
• pp.391-401
• /
• 2017

In this study, the effects of water-to-binder (W/B) ratio and replacement ratio of blast furnace slag (BFS) on the compressive strength of concrete were first investigated to determine an optimized mixture. Then, using the optimized high-strength concrete (HSC) mixture, hooked steel fibers with various aspect ratios and volume fractions were used as additives and the resulting mechanical properties under compression and flexure were evaluated. Test results indicated that replacement ratios of BFS from 50 to 60% were optimal in maximizing the compressive strength of steam-cured HSCs with various W/B ratios. The use of hooked steel fibers with the aspect ratio of 80 led to better mechanical performance under both compression and flexure than those with the aspect ratio of 65. By increasing the fiber aspect ratio from 65 to 80, the hooked steel fiber volume content could be reduced by 0.25% without any significant deterioration of energy absorption capacity. Lastly, complete material models of steel-fiber-reinforced HSCs were proposed for structural design from Lee's model and the RILEM TC 162-TDF recommendations.

• 접착 및 계면
• /
• 제12권4호
• /
• pp.138-143
• /
• 2011

특수한 방향족 화합물인 biphenylene 성분이 도입된 novolac 유도체를 기본 골격으로 하는 에폭시 수지 경화물은 난연제의 도움 없이도 자기소화성을 발현하며, 최근에 친환경 EMC (Epoxy Molding Compound) 소재로 상용화되고 있다. 본 연구에서는 이들을 골격으로 하는 에폭시수지와 경화제로 이루어진 경화물을 제조하여 DSC, DMA, TMA, TGA로부터 phenol 유도체의 분자구조와 반응성, 열팽창성, 탄성율 및 열분해성 등을 검토하였다. 주제와 경화제의 골격구조로 biphenyl novolac 구조가 모두 함유할 때 저팽창성, 기계적 성능 및 연소지연성 등이 우수하게 나타났다.

• 한국염색가공학회지
• /
• 제19권5호
• /
• pp.1-7
• /
• 2007

A new UV-curable coating was carried out to impart the flame-retardant property to cotton fabric using Bis[2-(methacryloyloxy)ehtyl]phosphate(DMEP) and 2-hydroxy-2-methyl-1-phenyl-propan-l-one(HMPP) as a UV-curable monomer and a photoinitiator, respectively. The cotton fabrics were applied with various amounts of DMEP and HMPP via padding and UV irradiation, and the optimal concentrations of DMEP and HMPP in the formulation were 40%(w/w) and 7%omp respectively. A limiteed oxygen index(LOI) up to 28.9 was obtained for the UV-cured fabric, which may occur through a condensed phase mechanism as verified by the increased residue number with increased application level. The characterization of the UV-cured coating was made by IR analysis, thermo-gravimetric analysis, LOI test, and scanning electron microscopy.

• Korean Chemical Engineering Research
• /
• 제50권4호
• /
• pp.621-626
• /
• 2012

본 연구에서는 마이크로 기공의 중공구를 유기 고분자 수지와 복합화한 유/무기 하이브리드 물질을 제조하여 우수한 단열 성능을 갖는 코팅유리를 개발하고자 하였다. 유기 고분자 물질로는 투명성과 접착성이 우수한 6관능기의 우레탄 아크릴레이트(UP118), 3관능기의 trimethylolpropane triacrylate (TMPTA), 2관능기의 1,6-hexanediol diacrylate (HDDA), 광 개시제(Irgacure184) 등으로 구성된 자외선 경화형 수지를 사용하였다. 유리 및 실리카 중공구를 고분자 수지에 각각 10~40 vol%까지 첨가하여 얻어진 코팅 졸을 투명유리에 바(bar)코팅 방식으로 박막을 형성시킨 후 자외선 경화를 통해 최종 코팅유리를 제조하였다. 마이크로 중공구의 종류 및 함량이 제조된 코팅유리의 광 투과율, 열전도도, 접착성 및 표면 경도에 미치는 영향을 조사하였다. 복합물 코팅유리는 중공구가 과량 첨가되어도 우수한 접착성(5B)을 유지하였으며, 단열 성능은 각 중공구가 20 vol%만 함유되어도 뚜렷하게 향상된 결과를 나타냈다. 또한 실리카 중공구(SP)를 단열 재료로 사용하였을 경우 광 투과율 80 %의 투명 코팅유리를 얻을 수 있었다.

• 콘크리트학회논문집
• /
• 제20권1호
• /
• pp.109-116
• /
• 2008

본 연구는 시멘트계의 self-healing 반응에 대한 정보와 콘크리트용 구체방수재가 self-healing에 미치는 영향에 대한 정보를 얻기 위하여 수행되었다. 우선 시멘트페이스트를 준비하여 7, 14, 28일간 양생한 다음 분쇄하여 두께가 1 mm 이하인 시편을 분리하였다. 분리한 시편은 밑면과 윗면을 젖은 헝겊으로 감싼 다음 용기에 담아 7일, 28일간 보관하였다. 그 후 젖은 헝겊으로 덮어 두었던 시편을 대상으로 아세톤을 사용하여 수화 정지 작업을 한 다음 XRD, DSC, SEM, EDX를 사용하여 분석하였다. 이러한 분석 결과 시멘트의 self-healing에 대한 정보를 얻을 수 있었다. 시멘트는 self-healing의 특성을 가지고 있으며 이러한 현상은 물의 존재에 큰 영향을 받게 된다. 또한 self-healing은 수화 초기에 더욱 빠르고 효과적인데, 이는 수화 초기 일수록 미반응 시멘트 성분의 함량이 높아 추가적인 수화반응을 일으키기가 수월하기 때문이다. 또한 연구 결과 콘크리트용 구체방수재가 시멘트계의 self-healing에 상당한 영향을 미치는 것을 확인하였다. 구체방수재는 시멘트의 self-healing 효과를 증대시켜주며, 특히 C 구체방수재를 사용한 시편에서는 침상 또는 섬유상의 수화생성물이 다량 존재하는 것으로 나타났으며, 이들 상은 에트린자이트로 예상되어진다. 이들 수화생성물이 시멘트계의 self-healing 효과를 증진하는데 매우 효과적인 것으로 판단된다.

• 한국응용과학기술학회지
• /
• 제29권1호
• /
• pp.141-148
• /
• 2012

본 연구에서는 초소수성 실리카 에어로겔을 이용하여 단열 성능을 갖는 투명 필름용 유/무기 복합 코팅물질을 제조하였다. 바인더 물질로 사용된 자외선 경화형 우레탄 아크릴레이트 수지와 에어로겔과의 상용성을 위해 계면활성제(Brij 56)를 이용하여 에어로겔의 표면을 개질하였다. 개질된 에어로겔을 고분자 수지와 복합화한 코팅 용액을 폴리카보네이트 기지재에 코팅한 후 자외선경화를 통해 코팅필름을 제조하였다. 에어로겔이 10 vol% 함량으로 첨가되었을 때, 코팅필름의 단열성능은 측정된 열전도도 기준으로 순수 기지재 대비 28% 정도로 향상되었다. 또한, 코팅필름의 광투과율은 에어로겔이 50 vol%로 과량 첨가된 경우에도 80% 이상 높은 수준을 유지하였으며, 우수한 접착성(5B) 및 연필 경도(4H)를 보여주었다.

• Restorative Dentistry and Endodontics
• /
• 제27권4호
• /
• pp.403-410
• /
• 2002

Several ways of curing are being tried to improve material's properties and reduce marginal gap. However, all are considering about the pattern of light intensity. It was noted from the preliminary study the change of light wavelength from filter changing may give an impact on material's property and microleakage. The object of this study was to verify the effect of filters with various wavelength width on the microhardness and microleakage of composite resin ; hybrid type of DenFil and submicron hybrid type of Esthet X. Composite resins were cured using 3 kinds of filter; narrow-banded(465-475 nm), mid-banded(430-470 nm), wide-banded(400-500 nm). After the estimation of microhardness. degree of dye penetration and the maximum gap from SEM evaluation were done between 4 groups that showed no difference in microhardness value of the lower surface . The results were as follows : 1 Adequate microhardness could not be gained with a narrow-banded filter irrespective of curing time. At the upper surface, DenFil should be polymerized with middle or wide-banded filter for 20 seconds at least, while Esthet X be col$.$ed with middle or wide-banded filter for 30 seconds at least to get simitar hardness value to control group. 2. There was little dye penetration in enamel margin, but all dentin margins skewed much more dye penetration irrespective of curing conditions. Although there was no statistical difference, groups cured with mid-banded filter for 40 seconds and with wide-width filter for 20 seconds showed relatively less dye penetration. 3. It was revealed from the SEM examination that group cured with wide-banded filter had the smallest gap without statistical significance. Spearman's rho test showed that the correlation between the results of dye penetration and SEM examination was very low. From these results, it could be concluded that curing with wide-width filter would be better than the other techniques, even though the curing technique using mid-width filter seems to have its own unique advantage.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2004년도 Asia Display / IMID 04
• /
• pp.592-594
• /
• 2004

We have investigated the photolithographic patterning method of light emitting polymer film for polymer light emitting diodes (PLEDs). Blue light emitting polymers based on polyfluorene, which can be cured photochemically to yield an insoluble form, have been synthesized using Ni(0) mediated Yamamoto polymerization. The relationship between patterning property and several variables such as the intensity of the exposed UV light, the concentrations of additives, has been studied by using optical microscope analysis, UV/visible spectroscopy, and photoluminescence. We have successfully fabricated PLEDs composed of the patterned emissive layer and their electroluminescence property has been also investigated. In this presentation, the detailed photolithographic patterning method and its application for polymer light emitting display will be discussed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 디스플레이 광소자분야
• /
• pp.106-108
• /
• 2004

We have investigated the photolithographic patterning method of light emitting polymer film for polymer light emitting diodes (PLED). Blue light emitting polymers based on polyfluorene, which can be cured photochemically to yield an insoluble form, have been synthesized using Ni(0) mediated Yamamoto polymerization. The relationship between patterning property and several variables such as the intensity of the exposed UV light, the concentrations of additives, has been studied by using optical microscope analysis, UV/visible spectroscopy, and photoluminescence. We have successfully fabricated PLEDs composed of the patterned emissive layer and their electroluminescence property has been also investigated. In this presentation, the detailed photolithographic patterning method and its application for polymer light emitting display will be discussed.