• Journal of the Korean institute of surface engineering
• /
• v.26 no.3
• /
• pp.149-157
• /
• 1993

In the study of TAB(Tape Automated Bonding)technologies, Cu-Cr sputtered seed layer has been used to improve the adhesion between Polyimide and Cu film and electrical properties. But the Cu electrodeposit on Cu-Cr film had poor adhesion or powder-like form due to the surface Cr oxides on the Cu-Cr film. By means of activating the Cu-Cr film with the oxalic acid and phosphoric acid, the Cu film with the improved adhesion could be coated on the Cu-Cr sputtered film in CuSO4 solution. The etching rate was compared with increasing the Cr content of the sputtered Cu-Cr film, and anodic polarization curve in FeCl3 solution was investigated. With increasing the Cr content, the etching rate was reduced. The clean etching cross section could be obtained with increasing the concentration of FeCl3 solution. But above the 13 w/o Cr content, Cu-Cr sputtered film could not bed etched cleanly only with FeCl3 solution and additives were needed.

• Clean Technology
• /
• v.23 no.1
• /
• pp.27-33
• /
• 2017

In this study, toxicities of seven metals (Cu, Cd, Cr, As(III), As(V), Zn, Ni) and five metal oxide nanoparticles (NPs: CuO, ZnO, NiO, $TiO_2$, $Fe_2O_3$) were evaluated based on the growth of Chlorella vulgaris. Effect on algae growth was evaluated by integrating the results of absorption, chlorophyll content, and cell count. The toxicity rankings of metals was observed as Cr ($0.7mgL^{-1}$) > Cu ($1.7mgL^{-1}$) > Cd ($3.2mgL^{-1}$) > Zn ($3.9mgL^{-1}$) > Ni ($13.2mgL^{-1}$) > As(III) ($17.8mgL^{-1}$) ${\gg}$ As(V) (> $1000mgL^{-1}$). Slightly different orders and sensitivities of metal toxicity were examined depending on endpoints of algal growth. In case of NPs, regardless of endpoints, similar toxicity rankings of NPs ($TEC_{50}$) were observed, showing ZnO ($2.4mgL^{-1}$) > NiO ($21.1mgL^{-1}$) > CuO ($36.6mgL^{-1}$) > $TiO_2$ ($62.5mgL^{-1}$) > $Fe_2O_3$ ($82.7mgL^{-1}$). These results indicate that an integrating results of endpoints might be an effective strategy for the assessment of contaminants.

• Korean Journal of Soil Science and Fertilizer
• /
• v.31 no.2
• /
• pp.107-113
• /
• 1998

We investigated the effects of a long term application of soil amendments such as lime, silicate, compost, or combinations of these materials on the contents of Cu and Zn in paddy soil and brown rice. The results obtained from a sequential extraction of Cu and Zn in paddy soils and brown rice, using $H_2O$, $KNO_3$, $Na_2$-EDTA and $HNO_3$ and showed that the most of Cu and Zn were NaOH-extractable (organically bound form) and $HNO_3$-extractable (sulfide and residual form). Cu contents of NaOH and EDTA extractable increased with the long term application of compost while the contents of Zn extracted by $KNO_3$ was decreased even though $HNO_3$ extractable-Zn was prominent chemical form in paddy soils. The percentage and contents of Zn, extracted by $KNO_3$ for each combination treatment of soil amendments, was decreased but the contents of Cu was not affected. The content of NaOH extractable-Cu was proportionally increased with increase in organic matter content irrespective of the extractants used in this experiment. The contents of Zn and exchangeable K were also increased with increase in organic matter content. However, we could not find any relationship between the extractable forms of Cu and Zn, and CEC, OM. while increase in CEC, contents of cations, and organic matter decreased the content of Cu in brown rice.

• Resources Recycling
• /
• v.26 no.4
• /
• pp.95-100
• /
• 2017

In this study, $Fe_2O_3$ was added as a flux to decrease melting temperature and refine during melting of Cu powder from scraped surface of the waste PCB (printed circuit board). The effect of $Fe_2O_3$ ratio to Cu powder and temperature on the recovery of Cu and content of impurities were investigated. It was found that the recovery of Cu was increased with increasing addition ratio of $Fe_2O_3$ and reaction temperature. The contents of O, Si and Fe in Cu phase were also decreased with increasing addition ratio of $Fe_2O_3$ and temperature. The formation of fayalite ($2FeO{\cdot}SiO_2$) and iron oxides phases in the slag was confirmed by XRD analysis after reaction with $Fe_2O_3$. Therefore, it was considered that the decrease of melting temperature and viscosity of slag by formation of fayalite slag contributed remarkably to the Cu recovery.

• Journal of Welding and Joining
• /
• v.13 no.3
• /
• pp.55-64
• /
• 1995

Metallizing method on ceramic surface is one of the compositing technology of ceramics and metal. The purpose of this study is to make HIC (Hybrid Intergrated Circuit) with copper metallizing method of which copper layer is formed on ceramic substrate by firing in atmosphere in lieu of conventional hybrid microcircuit systems based on noble metal. Metallizing pastes were made from various copper compounds such as Cu$_{2}$O, CuO, Cu, CuS and kaolin. And the screen printing method was used. The characteristics of metallized copper layers were analyzed through the measurement of sheet resistance, SEM, and EDZX. The results obtainted are summarized as follows; 1. The copper metallizing layers on ceramic surface can be formed by firing in air. 2. The metallized layer using Cu$_{2}$O paste showed the smallest sheet resistance among a group of copper chemical compounds. And optimum metallizing conditions are 15 minutes of firing time, 1000.deg.C of firig temperature, and 3 minutes of deoxidation time. 3. The results of EDAX analysis showed mutual diffusion of Cu and Al. 4. The kaolin plays a important role of deepening the penetration of Cu to $Al_{2}$O$_{3}$ ceramics. But if the kaolin content is too much, sheet resistance increases and copper metallizing layer becomes brittle.

• Bulletin of the Korean Chemical Society
• /
• v.13 no.4
• /
• pp.425-428
• /
• 1992

Sodium substituted samples of $Y_{1-x}Na_xBa_2Cu_3O_{7-y}$ for $0.00{\leq}x{\leq}0.16$ were prepared and characterized by X-ray powder pattern, electrical resistivity and magnetic susceptibility measurements, Raman spectroscopy, and idometric titration. The Na substituted compounds have narrow solid solution limits where $0.00{\leq}x{\leq}0.16.$ As the Na concentration increases, the parent orthorhombic structure tends to gradually change to tetragonal. Small changes in the superconducting transition temperature, Tc, are observed in this solid solution region. Raman spectra for the Na phases are virtually identical with that of $YBa_2Cu_3O_7$ except that the Cu(1)-O(4) stretching mode at 504 $cm^{-1}$ and the Cu(2)-O(2,3) bending mode at 340 $cm^{-1}$ for x = 0.16 are slightly shifted. The hole concentrations of the sodium substituted compounds ranged from 0.31 to 0.33 per Cu site are increased with Na content. The substitution of $Na^+$ for $Y^{3+}$ site appears to create oxygen vacancies in the Cu-O chains, causes structural change from orthorhombic to tetragonal, and increases hole concentration in the substituted system.

• Journal of the Korean Magnetics Society
• /
• v.4 no.1
• /
• pp.12-19
• /
• 1994

The crystallization behavior of the amorphous $Fe_{73.5}Cu_{1}Nb_{3}Si_{16.5}B_{6}$ alloy with isothermal annealing at $552^{\circ}C$ was studied by $M\"{o}ssbauer$ spectroscopy. The amorphous phase was revealed to coexist together with $Do_{3}-FeSi$ nanocrystalline and Cu-duster in annealed alloys by $M\"{o}ssbauer$ spectrum analysis. At the early stage of crystallization, Si content of FeSi is high due to the creation of Cu-cluster, and decreases with annealing until 60 minutes, which results in the increase in the mean hyperfine field of FeSi, and thereafter keeps constant. After 60 minutes, the decrease in the mean hyperfine field of the residual armrphous, in spite of a slight change in the volume fraction of the FeSi and the residual armrphous, is caused by the increase in the content of Nb and B in residual amorphous phase. Both directions of the hyperfine field, those of the FeSi and the residual amorphous, become randomly oriented in about 60 minutes. For FeSi and Cu-duster, the Avrami exponents are 0.51 and O.65, the activation energies are 2.35 eV and 2.44 eV, and the incubation times are 2.4 minutes and 0.8 minutes respectively. Earlier formation of Cu-duster than that of FeSi is coincidence with the fact that Cu atom promotes the nucleation of the FeSi.

• Korean Journal of Materials Research
• /
• v.5 no.7
• /
• pp.786-793
• /
• 1995

Ag-doped $Y_1$Ba$_2$Cu$_3$O$_{7-y}$ samples have been prepared by solid state reaction. High-Tc super conductivity, microstructure and mechanical property of the Ag-doped $Y_1$Ba$_2$Cu$_3$O$_{7-y}$ samples have been studied. As the Ag content increased, the grain size of $Y_1$Ba$_2$Cu$_3$O$_{7-y}$, increased and connectivity between the grains was improved, and the sample becomed denser and harder than the undoped. From the result, it is concluded that Ag addition reduced weak link and weak coupling between grains and led to the strong coupling. Furthermore, the anisotropy of crytstal structure was decreased and thermal stability, mechanical property of $Y_1$Ba$_2$Cu$_3$O$_{7-y}$-Ag were improved.mproved.

• Korean Journal of Materials Research
• /
• v.12 no.9
• /
• pp.740-746
• /
• 2002

In this study, the polycarbonate surface was treated by $O_2$/ Ar gases plasma for the enhancement of adhesion with Cu electrode. From the point of view of hydrophilicity and the functionality, the micro-roughness, new functional groups and oxygen content of the polycarbonate surface were increased by the $O_2$/ Ar gases plasma treatment. The Cu films deposited on the as-received polycarbonate were easily detached while, after the$ O_2$/ Ar gases plasma treatment the adhesive Cu films on polycarbonate could be obtained. These results can be explained that the polycarbonate had a hydrophilic surface with uniform micro-roughness and new functional groups by $O_2$/ Ar gases plasma treatment. Therefore,$O_2$/ Ar gases plasma treatment is a promising method for improvement of adhesion between polycarbonate and Cu electrode.

• Applied Chemistry for Engineering
• /
• v.9 no.7
• /
• pp.956-960
• /
• 1998

Cu-Zn and Cu-Zn-Ti catalysts for the steam reforming of methanol were prepared. This reaction was carried out at atmospheric pressure, $250^{\circ}C$, steam/methanol molar ratio 1.5, and contact time 0.1 g-cat.hr/mL-feed. In case of the catalyst with 3 mol% of $TiO_2$, the activity was superior to that of catalysts without $TiO_2$. The reaction products were mainly hydrogen and carbon dioxide. It was found that catalytic activity was not related to specific surface area but affected by metallic copper area which was measured by $N_2O$ decomposition and increased with the addition of $TiO_2$ content. XPS and XRD showed that the oxidation state of zinc was not changed during reaction, but oxidation states of copper existed in Cu(0) or Cu(I).